main
Ray
Publish 0.1.0
7031a73
NCP1342ANACCED1R2G
onsemi · AC-DC Controllers & Regulators · SOP-10
NCP1342ANACCED1R2G from onsemi, in a SOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Fault | input | The controller enters fault mode if the voltage on this pin is pulled above or below the fault thresholds, and a precise pull-up current source allows direct interface with an NTC thermistor. |
| 2 | FMAX | input | A resistor to ground sets the maximum switching frequency clamp, and the maximum frequency clamp is disabled if this pin is pulled above 4 V. |
| 3 | FB | input | Feedback input for the QR flyback controller that allows direct connection to an optocoupler. |
| 4 | ZCD/OPP | input | A resistor divider from the auxiliary winding feeds the demagnetization detection comparator and sets the OPP compensation level, with input voltage limited to −0.3 V to VCC + 0.7 V and input current limited to −2/+5 mA. |
| 5 | CS | input | Input to the cycle-by-cycle current limit comparator. |
| 6 | GND | power_in | Ground reference of the controller. |
| 7 | DRV | output | Gate drive pin with high-current capability of −0.5 A / +0.8 A, suitable for driving high gate charge power MOSFETs. |
| 8 | VCC | power_in | Positive supply of the IC: the circuit starts when VCC exceeds 17 V and turns off below 9 V (typical), and the operating range after start-up is 9 V to 28 V (VCC maximum rating 30 V). |
| 9 | N/C | unconnected | Removed for creepage distance; no pin is present at this position on the package. |
| 10 | HV | input | Input for the high-voltage startup and brownout detection circuits, which also contain the line removal detection circuit that safely discharges the X2 capacitors when the line is removed (maximum input voltage 700 V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOP-10 |
| Category | Power Supply Chip |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Startup Threshold | VCC(on) | 16 | 17 | 18 | V | dV/dt = 0.1 V/ms; VCC increasing | 7 |
| Minimum Operating Voltage | VCC(off) | 8.5 | 9 | 9.5 | V | VCC decreasing | 7 |
| Operating Hysteresis | VCC(HYS) | 7.5 | V | VCC(on) − VCC(off) | 7 | ||
| Internal Latch / Logic Reset Level | VCC(reset) | 4.5 | 6.5 | 7.5 | V | VCC decreasing | 7 |
| Transition from Istart1 to Istart2 | VCC(inhibit) | 0.3 | 0.7 | 1.05 | V | VCC increasing, IHV = 650 µA | 7 |
| VCC Overvoltage Protection Threshold | VCC(OVP) | 27 | 28 | 29 | V | 7 | |
| Inhibit Current Sourced from VCC Pin | Istart1 | 0.2 | 0.5 | 0.65 | mA | VCC = 0 V | 7 |
| Start-Up Current Sourced from VCC Pin (−40°C to 105°C) | Istart2 | 2.4 | 3.75 | 5 | mA | VCC = VCC(on) − 0.5 V; −40°C to 105°C | 7 |
| Start-Up Current Sourced from VCC Pin (−40°C to 125°C) | Istart2 | 2 | 3.75 | 5 | mA | VCC = VCC(on) − 0.5 V; −40°C to 125°C | 7 |
| Supply Current, Fault or Latch | ICC1 | 0.115 | 0.25 | mA | VCC = VCC(on) − 0.5 V | 7 | |
| Supply Current, Skip Mode (excluding FB current) | ICC2 | 0.23 | 0.4 | mA | VFB = 0 V | 7 | |
| Supply Current, Operating | ICC3 | 1 | 1.5 | mA | fsw = 50 kHz, CDRV = open | 7 | |
| Rise Time | tDRV(rise) | 20 | 40 | ns | VDRV from 10% to 90% | 7 | |
| Fall Time | tDRV(fall) | 5 | 30 | ns | VDRV from 90% to 10% | 7 | |
| High State Voltage | VDRV(high2) | 10 | 12 | 14 | V | VCC = 30 V, RDRV = 10 kΩ | 8 |
| Low State Voltage | VDRV(low) | 0.25 | V | VFault = 0 V | 8 | ||
| Open Pin Voltage | VFB(open) | 4.8 | 5 | 5.1 | V | 8 | |
| VFB to Internal Current Setpoint Division Ratio | KFB | 3.7 | 4 | 4.3 | , | 8 | |
| Internal Pull-Up Resistor | RFB | 17 | 20 | 23 | kΩ | VFB = 0.4 V | 8 |
| Current Limit Threshold Voltage | VILIM1 | 0.76 | 0.8 | 0.84 | V | VCS increasing | 8 |
| Leading Edge Blanking Duration | tLEB1 | 220 | 265 | 330 | ns | DRV minimum width minus tdelay(ILIM1) | 8 |
| Minimum Peak Current (Versions xxxCx) | VCS(MIN) | 70 | 100 | 130 | mV | Versions xxxCx | 9 |
| Abnormal Overcurrent Fault Threshold Voltage | VILIM2 | 1.125 | 1.2 | 1.275 | V | VCS increasing, VFB = 4 V | 9 |
| Pull-Up Current Source | ICS | 0.7 | 1 | 1.5 | A | VCS = VILIM2 − 10 mV | 9 |
| Maximum Frequency Clamp (9-pin versions) | fMAX1 | 440 | 500 | 560 | kHz | VFMAX = 0.5 V | 8 |
| Maximum Frequency Clamp (9-pin versions) | fMAX2 | 61 | 70 | 79 | kHz | VFMAX = 3.5 V | 8 |
| FMAX Disable Threshold (9-pin versions) | VFMAX(disable) | 3.85 | 4 | 4.15 | V | 8 | |
| Maximum On Time | ton(MAX) | 28 | 32 | 40 | µs | 8 | |
| ZCD Threshold Voltage | VZCD(trig) | 35 | 60 | 90 | mV | VZCD decreasing | 8 |
| ZCD Hysteresis | VZCD(HYS) | 15 | 25 | 55 | mV | VZCD increasing | 8 |
| ZCD Clamp Voltage, Positive Clamp | VZCD(MAX) | 12.4 | 12.7 | 13 | V | IQZCD = 5.0 mA | 8 |
| Soft-Start Period | tSSTART | 2.8 | 4 | 5 | ms | Measured from 1st DRV pulse to VCS = VILIM1 | 9 |
| Flyback Overload Fault Timer (other versions) | tOVLD | 120 | 160 | 200 | ms | VCS = VILIM1; other versions (not Exxxx, Fxxxx) | 9 |
| Overvoltage Protection (OVP) Threshold | VFault(OVP) | 2.79 | 3 | 3.21 | V | VFault increasing | 9 |
| Overtemperature Protection (OTP) Threshold | VFault(OTP_in) | 380 | 400 | 420 | mV | VFault decreasing | 9 |
| Overtemperature Protection (OTP) Exiting Threshold | VFault(OTP_out) | 874 | 910 | 966 | mV | VFault increasing | 9 |
| Minimum Frequency Clamp | fMIN | 21.5 | 25 | 27 | kHz | 10 | |
| Quiet-Skip Timer (Versions xxAxx) | tquiet | 1.18 | 1.25 | 1.4 | ms | Versions xxAxx | 10 |
| Skip Threshold | Vskip | 350 | 400 | 450 | mV | VFB decreasing | 10 |
| Skip Hysteresis | Vskip(HYS) | 20 | 50 | 70 | mV | VFB increasing | 10 |
| Minimum Peak Current Shift (Versions xxxxC) | VMPCM(delta) | 250 | 300 | 350 | mV | Versions xxxxC | 10 |
| High Voltage Startup Circuit Input Voltage | VHV(MAX) | -0.3 | 700 | V | 6 | ||
| High Voltage Startup Circuit Input Current | IHV(MAX) | 20 | mA | 6 | |||
| Supply Input Voltage | VCC(MAX) | -0.3 | 30 | V | 6 | ||
| Supply Input Current | ICC(MAX) | 30 | mA | 6 | |||
| Supply Input Voltage Slew Rate | dVCC/dt | 1 | V/µs | 6 | |||
| Fault Input Voltage | VFault(MAX) | -0.3 | V | max = VCC + 0.7 V | 6 | ||
| Fault Input Current | IFault(MAX) | 10 | mA | 6 | |||
| Zero Current Detection and OPP Input Voltage | VZCD(MAX) | -0.3 | V | max = VCC + 0.7 V | 6 | ||
| Zero Current Detection and OPP Input Current | IZCD(MAX) | -2 | 5 | mA | 6 | ||
| Maximum Input Voltage (Other Pins) | VMAX | -0.3 | 5.5 | V | 6 | ||
| Maximum Input Current (Other Pins) | IMAX | 10 | mA | 6 | |||
| Driver Maximum Voltage | VDRV | -0.3 | V | max = VDRV(high) | 6 | ||
| Driver Maximum Current, Source | IDRV(SRC) | 500 | mA | 6 | |||
| Driver Maximum Current, Sink | IDRV(SNK) | 800 | mA | 6 | |||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 6 | ||
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 6 | |||
| Storage Temperature Range | TSTG | -60 | 150 | °C | 6 | ||
| Power Dissipation, D1R2G suffix SOIC-9 | PD(MAX) | 330 | mW | TA = 25°C, 1 oz. Cu, 42 mm² copper clad PCB | 6 | ||
| Thermal Resistance, junction-to-ambient, D1R2G suffix SOIC-9 | RJA | 300 | °C/W | TA = 25°C, 1 oz. Cu, 42 mm² copper clad PCB | 6 |
CAD (KiCad official)
- Symbol:
NCP1342ANACCED1R2G - Footprint:
Package_SO:SOIC-10_3.9x4.9mm_P1mm - 3D model: SOP-10, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.75 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
ncp1342anacced1r2g-etched.step/ncp1342anacced1r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp1342anacced1r2g.step/ncp1342anacced1r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (44 pp, sha256
c3d1b8a76d48b18a, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NCP1342ANACCED1R2G
**onsemi** · AC-DC Controllers & Regulators · SOP-10
NCP1342ANACCED1R2G from onsemi, in a SOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Fault | input | The controller enters fault mode if the voltage on this pin is pulled above or below the fault thresholds, and a precise pull-up current source allows direct interface with an NTC thermistor. |
| 2 | FMAX | input | A resistor to ground sets the maximum switching frequency clamp, and the maximum frequency clamp is disabled if this pin is pulled above 4 V. |
| 3 | FB | input | Feedback input for the QR flyback controller that allows direct connection to an optocoupler. |
| 4 | ZCD/OPP | input | A resistor divider from the auxiliary winding feeds the demagnetization detection comparator and sets the OPP compensation level, with input voltage limited to −0.3 V to VCC + 0.7 V and input current limited to −2/+5 mA. |
| 5 | CS | input | Input to the cycle-by-cycle current limit comparator. |
| 6 | GND | power_in | Ground reference of the controller. |
| 7 | DRV | output | Gate drive pin with high-current capability of −0.5 A / +0.8 A, suitable for driving high gate charge power MOSFETs. |
| 8 | VCC | power_in | Positive supply of the IC: the circuit starts when VCC exceeds 17 V and turns off below 9 V (typical), and the operating range after start-up is 9 V to 28 V (VCC maximum rating 30 V). |
| 9 | N/C | unconnected | Removed for creepage distance; no pin is present at this position on the package. |
| 10 | HV | input | Input for the high-voltage startup and brownout detection circuits, which also contain the line removal detection circuit that safely discharges the X2 capacitors when the line is removed (maximum input voltage 700 V). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOP-10 |
| Category | Power Supply Chip |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Startup Threshold | VCC(on) | 16 | 17 | 18 | V | dV/dt = 0.1 V/ms; VCC increasing | 7 |
| Minimum Operating Voltage | VCC(off) | 8.5 | 9 | 9.5 | V | VCC decreasing | 7 |
| Operating Hysteresis | VCC(HYS) | 7.5 | | | V | VCC(on) − VCC(off) | 7 |
| Internal Latch / Logic Reset Level | VCC(reset) | 4.5 | 6.5 | 7.5 | V | VCC decreasing | 7 |
| Transition from Istart1 to Istart2 | VCC(inhibit) | 0.3 | 0.7 | 1.05 | V | VCC increasing, IHV = 650 µA | 7 |
| VCC Overvoltage Protection Threshold | VCC(OVP) | 27 | 28 | 29 | V | | 7 |
| Inhibit Current Sourced from VCC Pin | Istart1 | 0.2 | 0.5 | 0.65 | mA | VCC = 0 V | 7 |
| Start-Up Current Sourced from VCC Pin (−40°C to 105°C) | Istart2 | 2.4 | 3.75 | 5 | mA | VCC = VCC(on) − 0.5 V; −40°C to 105°C | 7 |
| Start-Up Current Sourced from VCC Pin (−40°C to 125°C) | Istart2 | 2 | 3.75 | 5 | mA | VCC = VCC(on) − 0.5 V; −40°C to 125°C | 7 |
| Supply Current, Fault or Latch | ICC1 | | 0.115 | 0.25 | mA | VCC = VCC(on) − 0.5 V | 7 |
| Supply Current, Skip Mode (excluding FB current) | ICC2 | | 0.23 | 0.4 | mA | VFB = 0 V | 7 |
| Supply Current, Operating | ICC3 | | 1 | 1.5 | mA | fsw = 50 kHz, CDRV = open | 7 |
| Rise Time | tDRV(rise) | | 20 | 40 | ns | VDRV from 10% to 90% | 7 |
| Fall Time | tDRV(fall) | | 5 | 30 | ns | VDRV from 90% to 10% | 7 |
| High State Voltage | VDRV(high2) | 10 | 12 | 14 | V | VCC = 30 V, RDRV = 10 kΩ | 8 |
| Low State Voltage | VDRV(low) | | | 0.25 | V | VFault = 0 V | 8 |
| Open Pin Voltage | VFB(open) | 4.8 | 5 | 5.1 | V | | 8 |
| VFB to Internal Current Setpoint Division Ratio | KFB | 3.7 | 4 | 4.3 |, | | 8 |
| Internal Pull-Up Resistor | RFB | 17 | 20 | 23 | kΩ | VFB = 0.4 V | 8 |
| Current Limit Threshold Voltage | VILIM1 | 0.76 | 0.8 | 0.84 | V | VCS increasing | 8 |
| Leading Edge Blanking Duration | tLEB1 | 220 | 265 | 330 | ns | DRV minimum width minus tdelay(ILIM1) | 8 |
| Minimum Peak Current (Versions xxxCx) | VCS(MIN) | 70 | 100 | 130 | mV | Versions xxxCx | 9 |
| Abnormal Overcurrent Fault Threshold Voltage | VILIM2 | 1.125 | 1.2 | 1.275 | V | VCS increasing, VFB = 4 V | 9 |
| Pull-Up Current Source | ICS | 0.7 | 1 | 1.5 | A | VCS = VILIM2 − 10 mV | 9 |
| Maximum Frequency Clamp (9-pin versions) | fMAX1 | 440 | 500 | 560 | kHz | VFMAX = 0.5 V | 8 |
| Maximum Frequency Clamp (9-pin versions) | fMAX2 | 61 | 70 | 79 | kHz | VFMAX = 3.5 V | 8 |
| FMAX Disable Threshold (9-pin versions) | VFMAX(disable) | 3.85 | 4 | 4.15 | V | | 8 |
| Maximum On Time | ton(MAX) | 28 | 32 | 40 | µs | | 8 |
| ZCD Threshold Voltage | VZCD(trig) | 35 | 60 | 90 | mV | VZCD decreasing | 8 |
| ZCD Hysteresis | VZCD(HYS) | 15 | 25 | 55 | mV | VZCD increasing | 8 |
| ZCD Clamp Voltage, Positive Clamp | VZCD(MAX) | 12.4 | 12.7 | 13 | V | IQZCD = 5.0 mA | 8 |
| Soft-Start Period | tSSTART | 2.8 | 4 | 5 | ms | Measured from 1st DRV pulse to VCS = VILIM1 | 9 |
| Flyback Overload Fault Timer (other versions) | tOVLD | 120 | 160 | 200 | ms | VCS = VILIM1; other versions (not Exxxx, Fxxxx) | 9 |
| Overvoltage Protection (OVP) Threshold | VFault(OVP) | 2.79 | 3 | 3.21 | V | VFault increasing | 9 |
| Overtemperature Protection (OTP) Threshold | VFault(OTP_in) | 380 | 400 | 420 | mV | VFault decreasing | 9 |
| Overtemperature Protection (OTP) Exiting Threshold | VFault(OTP_out) | 874 | 910 | 966 | mV | VFault increasing | 9 |
| Minimum Frequency Clamp | fMIN | 21.5 | 25 | 27 | kHz | | 10 |
| Quiet-Skip Timer (Versions xxAxx) | tquiet | 1.18 | 1.25 | 1.4 | ms | Versions xxAxx | 10 |
| Skip Threshold | Vskip | 350 | 400 | 450 | mV | VFB decreasing | 10 |
| Skip Hysteresis | Vskip(HYS) | 20 | 50 | 70 | mV | VFB increasing | 10 |
| Minimum Peak Current Shift (Versions xxxxC) | VMPCM(delta) | 250 | 300 | 350 | mV | Versions xxxxC | 10 |
| High Voltage Startup Circuit Input Voltage | VHV(MAX) | -0.3 | | 700 | V | | 6 |
| High Voltage Startup Circuit Input Current | IHV(MAX) | | | 20 | mA | | 6 |
| Supply Input Voltage | VCC(MAX) | -0.3 | | 30 | V | | 6 |
| Supply Input Current | ICC(MAX) | | | 30 | mA | | 6 |
| Supply Input Voltage Slew Rate | dVCC/dt | | | 1 | V/µs | | 6 |
| Fault Input Voltage | VFault(MAX) | -0.3 | | | V | max = VCC + 0.7 V | 6 |
| Fault Input Current | IFault(MAX) | | | 10 | mA | | 6 |
| Zero Current Detection and OPP Input Voltage | VZCD(MAX) | -0.3 | | | V | max = VCC + 0.7 V | 6 |
| Zero Current Detection and OPP Input Current | IZCD(MAX) | -2 | | 5 | mA | | 6 |
| Maximum Input Voltage (Other Pins) | VMAX | -0.3 | | 5.5 | V | | 6 |
| Maximum Input Current (Other Pins) | IMAX | | | 10 | mA | | 6 |
| Driver Maximum Voltage | VDRV | -0.3 | | | V | max = VDRV(high) | 6 |
| Driver Maximum Current, Source | IDRV(SRC) | | | 500 | mA | | 6 |
| Driver Maximum Current, Sink | IDRV(SNK) | | | 800 | mA | | 6 |
| Operating Junction Temperature | TJ | -40 | | 125 | °C | | 6 |
| Maximum Junction Temperature | TJ(MAX) | | | 150 | °C | | 6 |
| Storage Temperature Range | TSTG | -60 | | 150 | °C | | 6 |
| Power Dissipation, D1R2G suffix SOIC-9 | PD(MAX) | | | 330 | mW | TA = 25°C, 1 oz. Cu, 42 mm² copper clad PCB | 6 |
| Thermal Resistance, junction-to-ambient, D1R2G suffix SOIC-9 | RJA | | | 300 | °C/W | TA = 25°C, 1 oz. Cu, 42 mm² copper clad PCB | 6 |
## CAD (KiCad official)
- Symbol: `NCP1342ANACCED1R2G`
- Footprint: `Package_SO:SOIC-10_3.9x4.9mm_P1mm`
- 3D model: SOP-10, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.75 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `ncp1342anacced1r2g-etched.step` / `ncp1342anacced1r2g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncp1342anacced1r2g.step` / `ncp1342anacced1r2g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncp1342anacced1r2-d.pdf) (44 pp, sha256 `c3d1b8a76d48b18a`, retrieved 2026-10-29, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ncp1342anacced1r2g-datasheet.pdf)