Generated by kicad-footprint-generator · KiCad file format 20260206
NCD57001FDWR2G
onsemi · Gate Drive ICs · SOIC-16-300mil
NCD57001FDWR2G from onsemi, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VEE2A | power_in | Output-side negative power supply; a good-quality bypass capacitor to GND2 should be placed close to the pins, and it should be connected to GND2 for unipolar supply operation. |
| 2 | DESAT | bidirectional | Desaturation detection input with an internal 0.5 mA (typ) blanking charge current; when DESAT reaches VDESAT-THR (9 V typ) the output is driven low, FLT is activated, and a 5 us mute time applies to IN+ and IN-. |
| 3 | GND2 | power_in | Output-side gate drive reference, connected to the IGBT emitter or FET source. |
| 4 | N/C | unconnected | Not connected. |
| 5 | VDD2 | power_in | Output-side positive power supply; operating range runs from UVLO2 to its maximum allowed value (24 V max per operating ranges), with a bypass capacitor to GND2 placed close to the pin. |
| 6 | OUT | output | Gate driver output supplying drive voltage and source/sink current to the IGBT/FET gate (peak 7.8 A source, 7.1 A sink); actively pulled low during start-up and fault conditions. |
| 7 | CLAMP | bidirectional | Miller clamp for the IGBT/FET gate during the off period; its internal N FET turns on when the pin voltage falls below VEE2 + VCLAMP-THR (1.5 to 2.5 V), and it must be tied directly to the gate with minimum trace length. |
| 8 | VEE2 | power_in | Output-side negative power supply; a good-quality bypass capacitor to GND2 should be placed close to the pins, and it should be connected to GND2 for unipolar supply operation. |
| 9 | GND1 | power_in | Input-side ground reference. |
| 10 | IN+ | input | Non-inverting gate driver input, internally clamped to VDD1 with a 50 kOhm pull-down to keep OUT low without an input signal; a minimum positive pulse width is required before OUT responds. |
| 11 | IN- | input | Inverting gate driver input, internally clamped to VDD1 with a 50 kOhm pull-up to keep OUT low without an input signal; a minimum negative pulse width is required before OUT responds. |
| 12 | RDY | output | Power-good output, active high when VDD2 is good, with an internal 50 kOhm pull-up; if a low RDY event is caused by UVLO2 the maximum low duration is 200 ns, and OUT remains low while RDY is low. |
| 13 | FLT | output | Active-low fault output that signals the controller that a desaturation condition occurred and the output has been deactivated; output current is limited to 10 mA maximum. |
| 14 | RST | input | Active-low reset input for the fault latch, with an internal 50 kOhm pull-up; the reset pulse must be at least 800 ns wide. |
| 15 | VDD1 | power_in | Input-side power supply, 3.3 V to 5 V (operating range up to 5.5 V). |
| 16 | GND1A | power_in | Input-side ground pin; Table 1 gives no separate description and lists this pin number under the GND1 row, with the name taken from the pin connection diagram. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-16-300mil |
| Category | Power Management ICs |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage, input side | VDD1-GND1 | -0.3 | 6 | V | 4 | ||
| Positive Power Supply, output side | VDD2-GND2 | -0.3 | 25 | V | 4 | ||
| Negative Power Supply, output side | VEE2-GND2 | -10 | 0.3 | V | 4 | ||
| Differential Power Supply, output side (VMAX2) | VDD2-VEE2 | 0 | 25 | V | 4 | ||
| Gate-driver output sourcing current (IPK-SRC) | IPK-SRC | 7.8 | A | maximum pulse width = 10 s, maximum duty cycle = 0.2%, VMAX2 = 20 V | 4 | ||
| Gate-driver output sinking current (IPK-SNK) | IPK-SNK | 7.1 | A | maximum pulse width = 10 s, maximum duty cycle = 0.2%, VMAX2 = 20 V | 4 | ||
| Clamp sinking current (IPK-CLAMP) | IPK-CLAMP | 2.5 | A | maximum pulse width = 10 s, maximum duty cycle = 0.2%, VCLAMP = 3 V | 4 | ||
| Output current of FLT, RDY | ILIM-GND1 | 10 | mA | 4 | |||
| Input to Output Isolation Voltage | VISO | -1200 | 1200 | V | 4 | ||
| Maximum Junction Temperature | TJ(max) | -40 | 150 | °C | 4 | ||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 4 | ||
| ESD Capability, Human Body Model | ESDHBM | -2 | 2 | kV | 4 | ||
| ESD Capability, Charged Device Model | ESDCDM | -2 | 2 | kV | 4 | ||
| Thermal Resistance, Junction-to-Air | RJA | 150 | °C/W | 100 mm2, 1 oz Copper, 1 Surface Layer | 4 | ||
| Thermal Resistance, Junction-to-Air | RJA | 84 | °C/W | 650 mm2, 1 oz Copper, 2 Surface Layers and 2 Internal Power Plane Layers | 4 | ||
| Supply voltage, input side | VDD1-GND1 | 5.5 | V | UVLO1 to 5.5 V | 5 | ||
| Positive Power Supply, output side | VDD2-GND2 | 24 | V | UVLO2 to 24 V | 5 | ||
| Negative Power Supply, output side | VEE2-GND2 | -10 | 0 | V | 5 | ||
| Differential Power Supply, output side (VMAX2) | VDD2-VEE2 | 0 | 24 | V | 5 | ||
| Ambient Temperature | TA | -40 | 125 | °C | 5 | ||
| UVLO2 Output Enabled | VUVLO2-OUT-ON | 13.2 | 13.5 | 13.8 | V | 5 | |
| UVLO2 Output Disabled | VUVLO2-OUT-OFF | 12.2 | 12.5 | 12.8 | V | 5 | |
| Input Supply Quiescent Current Output Low | IDD1-0 | 1 | 2 | mA | IN+ = Low, IN− = Low; RDY = High, FLT = High | 5 | |
| Input Supply Quiescent Current Output High | IDD1-100 | 4.8 | 6 | mA | IN+ = High, IN− = Low; RDY = High, FLT = High | 5 | |
| Output Positive Supply Quiescent Current, Output Low | IDD2-0 | 3.3 | 4 | mA | IN+ = Low, IN− = Low; RDY = High, FLT = High, no load | 5 | |
| Output Positive Supply Quiescent Current, Output High | IDD2-100 | 4 | 5 | mA | IN+ = High, IN− = Low; RDY = High, FLT = High, no load | 5 | |
| Output Negative Supply Quiescent Current, Output Low | IEE2-0 | 0.4 | 2 | mA | IN+ = High, IN− = Low, no load | 5 | |
| Output Negative Supply Quiescent Current, Output High | IEE2-100 | 0.2 | 2 | mA | IN+ = High, IN− = Low, no load | 5 | |
| UVLO2 Hysteresis | VUVLO2-HYST | 1 | V | 5 | |||
| Clamp Voltage | VCLAMP | 1.3 | 1.7 | V | ICLAMP = 2.5 A, TA = 25°C | 6 | |
| Clamp Activation Threshold | VCLAMP-THR | 1.5 | 2 | 2.5 | V | 6 | |
| Output Low State (VOUT, VEE2) | VOUTL1 | 0.1 | 0.2 | V | ISINK = 200 mA | 6 | |
| Output Low State (VOUT, VEE2) | VOUTL3 | 0.5 | 0.8 | V | ISINK = 1.0 A, TA = 25°C | 6 | |
| Output High State (VDD2, VOUT) | VOUTH1 | 0.3 | 0.5 | V | ISRC = 200 mA | 6 | |
| Output High State (VDD2, VOUT) | VOUTH3 | 0.8 | 1 | V | ISRC = 1.0 A, TA = 25°C | 6 | |
| DESAT Threshold Voltage | VDESAT-THR | 8.5 | 9 | 9.5 | V | 6 | |
| Blanking Charge Current | IDESAT-CHG | 0.45 | 0.5 | 0.55 | mA | VDESAT = 7 V | 6 |
| IN+, IN− to Output High Propagation Delay | tPD-ON | 40 | 60 | 90 | ns | CLOAD = 10 nF, VIH to 10% of output change for PW > 150 ns. OUT and CLAMP pins are connected together | 6 |
| IN+, IN− to Output Low Propagation Delay | tPD-OFF | 40 | 66 | 90 | ns | CLOAD = 10 nF, VIL to 90% of output change for PW > 150 ns. OUT and CLAMP pins are connected together | 6 |
| Propagation Delay Distortion (tPD-ON − tPD-OFF) | tDISTORT | -15 | -6 | 15 | ns | TA = 25°C, PW > 150 ns | 7 |
| Propagation Delay Distortion (tPD-ON − tPD-OFF) | tDISTORT | -25 | 25 | ns | TA = −40°C to 125°C, PW > 150 ns | 7 | |
| Prop Delay Distortion between Parts | tDISTORT_TOT | -30 | 0 | 30 | ns | PW > 150 ns | 7 |
CAD (KiCad official)
- Symbol:
NCD57001FDWR2G - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
ncd57001fdwr2g-etched.step/ncd57001fdwr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncd57001fdwr2g.step/ncd57001fdwr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (11 pp, sha256
e2c375fbe71b0d4a, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).