main
Ray Publish 0.1.0 42b6dc0

NCD57001FDWR2G

onsemi · Gate Drive ICs · SOIC-16-300mil

NCD57001FDWR2G from onsemi, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VEE2A power_in Output-side negative power supply; a good-quality bypass capacitor to GND2 should be placed close to the pins, and it should be connected to GND2 for unipolar supply operation.
2 DESAT bidirectional Desaturation detection input with an internal 0.5 mA (typ) blanking charge current; when DESAT reaches VDESAT-THR (9 V typ) the output is driven low, FLT is activated, and a 5 us mute time applies to IN+ and IN-.
3 GND2 power_in Output-side gate drive reference, connected to the IGBT emitter or FET source.
4 N/C unconnected Not connected.
5 VDD2 power_in Output-side positive power supply; operating range runs from UVLO2 to its maximum allowed value (24 V max per operating ranges), with a bypass capacitor to GND2 placed close to the pin.
6 OUT output Gate driver output supplying drive voltage and source/sink current to the IGBT/FET gate (peak 7.8 A source, 7.1 A sink); actively pulled low during start-up and fault conditions.
7 CLAMP bidirectional Miller clamp for the IGBT/FET gate during the off period; its internal N FET turns on when the pin voltage falls below VEE2 + VCLAMP-THR (1.5 to 2.5 V), and it must be tied directly to the gate with minimum trace length.
8 VEE2 power_in Output-side negative power supply; a good-quality bypass capacitor to GND2 should be placed close to the pins, and it should be connected to GND2 for unipolar supply operation.
9 GND1 power_in Input-side ground reference.
10 IN+ input Non-inverting gate driver input, internally clamped to VDD1 with a 50 kOhm pull-down to keep OUT low without an input signal; a minimum positive pulse width is required before OUT responds.
11 IN- input Inverting gate driver input, internally clamped to VDD1 with a 50 kOhm pull-up to keep OUT low without an input signal; a minimum negative pulse width is required before OUT responds.
12 RDY output Power-good output, active high when VDD2 is good, with an internal 50 kOhm pull-up; if a low RDY event is caused by UVLO2 the maximum low duration is 200 ns, and OUT remains low while RDY is low.
13 FLT output Active-low fault output that signals the controller that a desaturation condition occurred and the output has been deactivated; output current is limited to 10 mA maximum.
14 RST input Active-low reset input for the fault latch, with an internal 50 kOhm pull-up; the reset pulse must be at least 800 ns wide.
15 VDD1 power_in Input-side power supply, 3.3 V to 5 V (operating range up to 5.5 V).
16 GND1A power_in Input-side ground pin; Table 1 gives no separate description and lists this pin number under the GND1 row, with the name taken from the pin connection diagram.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-16-300mil
Category Power Management ICs
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage, input side VDD1-GND1 -0.3 6 V 4
Positive Power Supply, output side VDD2-GND2 -0.3 25 V 4
Negative Power Supply, output side VEE2-GND2 -10 0.3 V 4
Differential Power Supply, output side (VMAX2) VDD2-VEE2 0 25 V 4
Gate-driver output sourcing current (IPK-SRC) IPK-SRC 7.8 A maximum pulse width = 10 s, maximum duty cycle = 0.2%, VMAX2 = 20 V 4
Gate-driver output sinking current (IPK-SNK) IPK-SNK 7.1 A maximum pulse width = 10 s, maximum duty cycle = 0.2%, VMAX2 = 20 V 4
Clamp sinking current (IPK-CLAMP) IPK-CLAMP 2.5 A maximum pulse width = 10 s, maximum duty cycle = 0.2%, VCLAMP = 3 V 4
Output current of FLT, RDY ILIM-GND1 10 mA 4
Input to Output Isolation Voltage VISO -1200 1200 V 4
Maximum Junction Temperature TJ(max) -40 150 °C 4
Storage Temperature Range TSTG -65 150 °C 4
ESD Capability, Human Body Model ESDHBM -2 2 kV 4
ESD Capability, Charged Device Model ESDCDM -2 2 kV 4
Thermal Resistance, Junction-to-Air RJA 150 °C/W 100 mm2, 1 oz Copper, 1 Surface Layer 4
Thermal Resistance, Junction-to-Air RJA 84 °C/W 650 mm2, 1 oz Copper, 2 Surface Layers and 2 Internal Power Plane Layers 4
Supply voltage, input side VDD1-GND1 5.5 V UVLO1 to 5.5 V 5
Positive Power Supply, output side VDD2-GND2 24 V UVLO2 to 24 V 5
Negative Power Supply, output side VEE2-GND2 -10 0 V 5
Differential Power Supply, output side (VMAX2) VDD2-VEE2 0 24 V 5
Ambient Temperature TA -40 125 °C 5
UVLO2 Output Enabled VUVLO2-OUT-ON 13.2 13.5 13.8 V 5
UVLO2 Output Disabled VUVLO2-OUT-OFF 12.2 12.5 12.8 V 5
Input Supply Quiescent Current Output Low IDD1-0 1 2 mA IN+ = Low, IN− = Low; RDY = High, FLT = High 5
Input Supply Quiescent Current Output High IDD1-100 4.8 6 mA IN+ = High, IN− = Low; RDY = High, FLT = High 5
Output Positive Supply Quiescent Current, Output Low IDD2-0 3.3 4 mA IN+ = Low, IN− = Low; RDY = High, FLT = High, no load 5
Output Positive Supply Quiescent Current, Output High IDD2-100 4 5 mA IN+ = High, IN− = Low; RDY = High, FLT = High, no load 5
Output Negative Supply Quiescent Current, Output Low IEE2-0 0.4 2 mA IN+ = High, IN− = Low, no load 5
Output Negative Supply Quiescent Current, Output High IEE2-100 0.2 2 mA IN+ = High, IN− = Low, no load 5
UVLO2 Hysteresis VUVLO2-HYST 1 V 5
Clamp Voltage VCLAMP 1.3 1.7 V ICLAMP = 2.5 A, TA = 25°C 6
Clamp Activation Threshold VCLAMP-THR 1.5 2 2.5 V 6
Output Low State (VOUT, VEE2) VOUTL1 0.1 0.2 V ISINK = 200 mA 6
Output Low State (VOUT, VEE2) VOUTL3 0.5 0.8 V ISINK = 1.0 A, TA = 25°C 6
Output High State (VDD2, VOUT) VOUTH1 0.3 0.5 V ISRC = 200 mA 6
Output High State (VDD2, VOUT) VOUTH3 0.8 1 V ISRC = 1.0 A, TA = 25°C 6
DESAT Threshold Voltage VDESAT-THR 8.5 9 9.5 V 6
Blanking Charge Current IDESAT-CHG 0.45 0.5 0.55 mA VDESAT = 7 V 6
IN+, IN− to Output High Propagation Delay tPD-ON 40 60 90 ns CLOAD = 10 nF, VIH to 10% of output change for PW > 150 ns. OUT and CLAMP pins are connected together 6
IN+, IN− to Output Low Propagation Delay tPD-OFF 40 66 90 ns CLOAD = 10 nF, VIL to 90% of output change for PW > 150 ns. OUT and CLAMP pins are connected together 6
Propagation Delay Distortion (tPD-ON − tPD-OFF) tDISTORT -15 -6 15 ns TA = 25°C, PW > 150 ns 7
Propagation Delay Distortion (tPD-ON − tPD-OFF) tDISTORT -25 25 ns TA = −40°C to 125°C, PW > 150 ns 7
Prop Delay Distortion between Parts tDISTORT_TOT -30 0 30 ns PW > 150 ns 7

CAD (KiCad official)

  • Symbol: NCD57001FDWR2G
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: ncd57001fdwr2g-etched.step / ncd57001fdwr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncd57001fdwr2g.step / ncd57001fdwr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (11 pp, sha256 e2c375fbe71b0d4a, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF