Generated by kicad-footprint-generator · KiCad file format 20260206
NAU88L21YG
Nuvoton Tech · Audio Power OpAmps · QFN-32-EP(5x5)
NAU88L21YG from Nuvoton Tech, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MICDET | bidirectional | Microphone/button detect pin; a 2 kOhm resistor (internal or external) connects the microphone between MICBIAS and this pin. |
| 2 | MICBIAS | output | Microphone bias output whose level is set by register between VDDA and 1.53 x VDDA; microphones should not draw more than 4 mA from this pin. |
| 3 | VDDMIC | power_in | Microphone bias supply, recommended 3.0 V to 3.6 V (3.3 V typical). |
| 4 | VREF | power_in | Internal DAC and ADC mid-supply reference (about VDDA/2) decoupling pin; a 4.7 µF capacitor to VSSA is typically used. |
| 5 | VSSA | power_in | Analog ground; must be tied together with VSSD. |
| 6 | VDDA | power_in | Analog supply, recommended 1.62 V to 1.98 V (1.8 V typical); must be tied together with VDDC. |
| 7 | CPOUTP | bidirectional | Charge pump positive output voltage (about +VDDA unloaded), decoupled to VSSCP with about 2 µF ceramic. |
| 8 | VSSCP | power_in | Charge pump ground, used for the CPOUTP and CPOUTN decoupling capacitors. |
| 9 | CPOUTN | bidirectional | Charge pump negative output voltage (about -VDDA unloaded), decoupled to VSSCP with about 2 µF ceramic. |
| 10 | CPCB | bidirectional | Charge pump flying capacitor node B; the fly-back capacitor connects between CPCA and CPCB. |
| 11 | CPCA | bidirectional | Charge pump flying capacitor node A; the fly-back capacitor connects between CPCA and CPCB. |
| 12 | JKTIP(HPL) | output | Left-channel ground-referenced Class G headphone output (jack tip); can also be used as a lineout. |
| 13 | JKR1(HPR) | output | Right-channel ground-referenced Class G headphone output (jack ring 1); can also be used as a lineout. |
| 14 | HPFB | power_in | Headphone ground reference for the ground-referenced headphone outputs (listed as type Ground in the source table). |
| 15 | IRQ | bidirectional | Interrupt request pin; active low by default and configurable to active high, with pull and drive options set by register. |
| 16 | GPIO1/CSB | bidirectional | General purpose I/O / chip select; pulling it low selects I2C device address 0x1B and pulling it high selects 0x54. |
| 17 | SDIO | bidirectional | I2C serial data line for control register access (NAU88L21 acts as slave only). |
| 18 | SCLK | input | I2C serial data clock input for control register access. |
| 19 | VDDB | power_in | Digital I/O supply, recommended 1.62 V to 3.6 V. |
| 20 | VSSD | power_in | Digital I/O ground; must be tied together with VSSA. |
| 21 | VDDC | power_in | Digital core supply; must be tied together with VDDA. |
| 22 | MCLK | input | Codec master clock input; the internal MCLK should be 256 x Fs (for example 12.288 MHz at 48 kHz) for best performance. |
| 23 | BCLK | bidirectional | Serial data bit clock input (slave) or output (master) for I2S or PCM audio data. |
| 24 | FS | bidirectional | Frame sync input (slave) or output (master) for I2S or PCM audio data. |
| 25 | DACIN | input | Serial audio data input to the DACs for I2S or PCM data. |
| 26 | ADCOUT | output | Serial audio data output from the ADCs for I2S or PCM data. |
| 27 | JKDET/GPIO2 | input | Jack detect input supplied by VDDA (also usable as GPIO2 per register configuration). |
| 28 | MICR+ | input | PGA MICR+ analog input, AC-coupled, with a fixed 12 kOhm input impedance. |
| 29 | MICR-/DMCLK | output | PGA MICR- analog input, or digital microphone clock output (DMICCLK) when digital microphone mode is used. |
| 30 | MICL-/DMDATA | input | PGA MICL- analog input, or digital microphone data input (DMICDATA) when digital microphone mode is used. |
| 31 | MICL+ | input | PGA MICL+ analog input, AC-coupled, with a fixed 12 kOhm input impedance. |
| 32 | VDDA | power_in | Analog supply listed a second time in the pin table; treat as analog supply, recommended 1.62 V to 1.98 V. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nuvoton Tech |
| Package | QFN-32-EP(5x5) |
| Category | Operational Amplifier/Comparator |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Shutdown Current (VDDA) | ISD | 4 | 16 | µA | VDDA | 8 | |
| Shutdown Current (VDDB) | ISD | 0.2 | 1 | µA | VDDB | 8 | |
| Shutdown Current (VDDMIC) | ISD | 0.2 | 1 | µA | VDDMIC | 8 | |
| Headset Detection Standby Mode Current | IDD | 10 | µA | MCLK off, Jack Insertion, IRQ enabled | 8 | ||
| Active Current Normal Playback Mode | IDD | 5 | mA | fS = 48kHz, Stereo HP DAC On, HP On, POUT = 0mW. RL(HP) = 32Ω | 8 | ||
| Output Power (RL=32Ω) | PO | 28 | mW | Stereo RL = 32Ω, DAC Input, CPVVDD = 1.8V, f=1020Hz, 22kHz BW, THD+N = 1% (QFN package) | 8 | ||
| Output Power (RL=16Ω) | PO | 33 | mW | Stereo RL = 16Ω, DAC Input, CPVVDD = 1.8V, f=1020Hz, 22kHz BW, THD+N = 1% (QFN Package) | 8 | ||
| Total Harmonic Distortion + Noise | THD+N | -88 | dB | RL = 32Ω, f=1020Hz, PO = 20mW | 8 | ||
| Signal to Noise Ratio | SNR | 105 | dB | VOUT = 1VRMS, DAC Input, DAC_Gain = 0dB, HP_Gain = 0dB, Digital Zero Input, f=1020Hz, A-Weighted | 8 | ||
| Signal to Noise Ratio (auto attenuate) | SNR | 108 | dB | VOUT = 1 VRMS, DAC Input, DAC_Gain = 0dB, HP_Gain = 0dB, Digital Zero Input, f=1020Hz, A-Weighted, auto attenuate enabled | 8 | ||
| Power Supply Rejection Ratio (HP) | PSRR | 85 | dB | fRIPPLE = 217Hz, VRIPPLE = 200mVP_P Input Referred, HP_GAIN = 0dB DAC Input, DAC_Gain = 0dB Ripple Applied to VDDA | 8 | ||
| Channel Crosstalk | XTALK | 70 | dB | Left Channel to Right Channel, -1dBFS, Gain = 0dB, f = 1020Hz | 8 | ||
| Interchannel Level Mismatch | -0.1 | 0.1 | dB | 8 | |||
| Frequency Response (HP) | -0.2 | 0.1 | dB | F = 20Hz ~ 20kHz | 8 | ||
| Output Noise | eOS | 4.4 | µVRMS | DAC_Gain = 0dB, HP_Gain = 0dB, fS=48kHz, OSRDAC = 128, A-Weighted | 8 | ||
| Out of Band Noise Level | -60 | dB | 8 | ||||
| Output Offset Voltage | VOS | -1 | 1 | mV | HP_Gain = 0dB, DAC_Gain= 0dB, DAC Input | 8 | |
| Power Consumption MP3 Mode | 6 | mW | No Load, No Signal, Amp on fS = 48kHz, Stereo DAC On, Amp On, POUT = 0mW. RL = 32Ω | 8 | |||
| Fs Accuracy (44.1 / 48 kHz) | -0.02 | 0.02 | % | 8 | |||
| Pop and Click Noise | 1 | mVrms | 9 | ||||
| ADC Total Harmonic Distortion + Noise (MIC_GAIN 0dB) | THD+N | -91 | dB | MIC Input, MIC_GAIN = 0dB, VIN = 0.8Vrms, f=1020Hz, fs = 48KHz, Mono Differential Input | 9 | ||
| ADC Total Harmonic Distortion + Noise (MIC_GAIN 30dB) | THD+N | -80 | dB | MIC Input, MIC_GAIN = 30dB, Volume = 0dB, Vin=28.5mVrms, f=1020Hz, Digital Gain = 0dB, Mono Differential Input | 9 | ||
| ADC Signal to Noise Ratio (MIC Gain 0dB) | SNR | 102 | dB | Reference = VOUT(0dBFS), A-Weighted, MIC Input, MIC Gain = 0dB,fs = 48kHz, Mono Differential Input | 9 | ||
| ADC Signal to Noise Ratio (MIC Gain 6dB) | SNR | 101 | dB | Reference = VOUT(0dBFS), A-Weighted, MIC Input, MIC Gain = 6dB,fs = 48kHz, Mono Differential Input | 9 | ||
| ADC Power Supply Rejection Ratio | PSRR | 80 | dB | VRIPPLE = 200mVPP applied to VDDA, fRIPPLE = 217Hz, Input Referred, MIC_GAIN = 0dB Differential Input | 9 | ||
| Common Mode Rejection Ratio | CMRR | 65 | dB | Differential Input 100mVrms, PGA gain = 20dB, frequency sweep from 20Hz to 20KHz | 9 | ||
| ADC Full Scale Input Level | FSADC | 1 | VRMS | VDDA= 1.8V, ADC VREFSEL = 01'b, DGAINR_ADC = DGAINL_ADC = D0'b Differential Input | 9 | ||
| Minimum Input Impedance | 10 | kOhm | 9 | ||||
| ADC Frequency Response | -0.2 | 0.1 | dB | f = 20Hz ~ 20kHz | 9 | ||
| ADC Power Consumption | 5 | mW | No Signal, ADC on fs = 44.1kHz | 9 | |||
| MICBIAS Output Voltage | VBIAS | 2.5 | V | Programmable 1.8V to 3.0V in 6 steps | 9 | ||
| MICBIAS Output Current | IOUT | 27 | mA | 9 | |||
| MICBIAS Output Noise | eos | 47 | nV/√Hz | Low noise mode, at 1kHz | 9 | ||
| Digital Supply Voltage (VDDB) Recommended Range | VDDB | 1.62 | 3.3 | 3.6 | V | Digital I/O Supply Range | 10 |
| Analog Supply Voltage (VDDA) Recommended Range | VDDA | 1.62 | 1.8 | 1.98 | V | Analog Supply Range | 10 |
| Headphone Supply Voltage (VDDA) Recommended Range | VDDA | 1.62 | 1.8 | 1.98 | V | Headphone Supply Range | 10 |
| Microphone Bias Supply Voltage (VDDMIC) | VDDMIC | 3 | 3.3 | 3.6 | V | Microphone Bias Supply Voltage | 10 |
| Temperature Range | TA | -40 | 85 | °C | 10 | ||
| Digital Supply Range (Absolute Maximum) | -0.3 | 2.2 | V | Digital Supply Range | 10 | ||
| Digital I/O Supply Range (Absolute Maximum) | -0.3 | 4 | V | Digital I/O Supply Range | 10 | ||
| Analog Supply Range (Absolute Maximum) | -0.3 | 2.2 | V | Analog Supply Range | 10 | ||
| Headphone Supply Range (Absolute Maximum) | -0.3 | 2.2 | V | Headphone Supply Range | 10 | ||
| Microphone Bias Supply Voltage (Absolute Maximum) | -0.3 | 4 | V | Microphone Bias Supply Voltage | 10 | ||
| Junction Temperature | TJ | -40 | 150 | °C | 10 | ||
| Storage Temperature | -65 | 150 | °C | 10 |
CAD (KiCad official)
- Symbol:
NAU88L21YG - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
nau88l21yg-etched.step/nau88l21yg-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);nau88l21yg.step/nau88l21yg.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nuvoton Tech datasheet (80 pp, sha256
cea58f259542512b, retrieved 2026-11-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).