main
History Download
Ray Publish 0.1.0 70addeb

NAU88L21YG

Nuvoton Tech · Audio Power OpAmps · QFN-32-EP(5x5)

NAU88L21YG from Nuvoton Tech, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MICDET bidirectional Microphone/button detect pin; a 2 kOhm resistor (internal or external) connects the microphone between MICBIAS and this pin.
2 MICBIAS output Microphone bias output whose level is set by register between VDDA and 1.53 x VDDA; microphones should not draw more than 4 mA from this pin.
3 VDDMIC power_in Microphone bias supply, recommended 3.0 V to 3.6 V (3.3 V typical).
4 VREF power_in Internal DAC and ADC mid-supply reference (about VDDA/2) decoupling pin; a 4.7 µF capacitor to VSSA is typically used.
5 VSSA power_in Analog ground; must be tied together with VSSD.
6 VDDA power_in Analog supply, recommended 1.62 V to 1.98 V (1.8 V typical); must be tied together with VDDC.
7 CPOUTP bidirectional Charge pump positive output voltage (about +VDDA unloaded), decoupled to VSSCP with about 2 µF ceramic.
8 VSSCP power_in Charge pump ground, used for the CPOUTP and CPOUTN decoupling capacitors.
9 CPOUTN bidirectional Charge pump negative output voltage (about -VDDA unloaded), decoupled to VSSCP with about 2 µF ceramic.
10 CPCB bidirectional Charge pump flying capacitor node B; the fly-back capacitor connects between CPCA and CPCB.
11 CPCA bidirectional Charge pump flying capacitor node A; the fly-back capacitor connects between CPCA and CPCB.
12 JKTIP(HPL) output Left-channel ground-referenced Class G headphone output (jack tip); can also be used as a lineout.
13 JKR1(HPR) output Right-channel ground-referenced Class G headphone output (jack ring 1); can also be used as a lineout.
14 HPFB power_in Headphone ground reference for the ground-referenced headphone outputs (listed as type Ground in the source table).
15 IRQ bidirectional Interrupt request pin; active low by default and configurable to active high, with pull and drive options set by register.
16 GPIO1/CSB bidirectional General purpose I/O / chip select; pulling it low selects I2C device address 0x1B and pulling it high selects 0x54.
17 SDIO bidirectional I2C serial data line for control register access (NAU88L21 acts as slave only).
18 SCLK input I2C serial data clock input for control register access.
19 VDDB power_in Digital I/O supply, recommended 1.62 V to 3.6 V.
20 VSSD power_in Digital I/O ground; must be tied together with VSSA.
21 VDDC power_in Digital core supply; must be tied together with VDDA.
22 MCLK input Codec master clock input; the internal MCLK should be 256 x Fs (for example 12.288 MHz at 48 kHz) for best performance.
23 BCLK bidirectional Serial data bit clock input (slave) or output (master) for I2S or PCM audio data.
24 FS bidirectional Frame sync input (slave) or output (master) for I2S or PCM audio data.
25 DACIN input Serial audio data input to the DACs for I2S or PCM data.
26 ADCOUT output Serial audio data output from the ADCs for I2S or PCM data.
27 JKDET/GPIO2 input Jack detect input supplied by VDDA (also usable as GPIO2 per register configuration).
28 MICR+ input PGA MICR+ analog input, AC-coupled, with a fixed 12 kOhm input impedance.
29 MICR-/DMCLK output PGA MICR- analog input, or digital microphone clock output (DMICCLK) when digital microphone mode is used.
30 MICL-/DMDATA input PGA MICL- analog input, or digital microphone data input (DMICDATA) when digital microphone mode is used.
31 MICL+ input PGA MICL+ analog input, AC-coupled, with a fixed 12 kOhm input impedance.
32 VDDA power_in Analog supply listed a second time in the pin table; treat as analog supply, recommended 1.62 V to 1.98 V.
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Nuvoton Tech
Package QFN-32-EP(5x5)
Category Operational Amplifier/Comparator
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Shutdown Current (VDDA) ISD 4 16 µA VDDA 8
Shutdown Current (VDDB) ISD 0.2 1 µA VDDB 8
Shutdown Current (VDDMIC) ISD 0.2 1 µA VDDMIC 8
Headset Detection Standby Mode Current IDD 10 µA MCLK off, Jack Insertion, IRQ enabled 8
Active Current Normal Playback Mode IDD 5 mA fS = 48kHz, Stereo HP DAC On, HP On, POUT = 0mW. RL(HP) = 32Ω 8
Output Power (RL=32Ω) PO 28 mW Stereo RL = 32Ω, DAC Input, CPVVDD = 1.8V, f=1020Hz, 22kHz BW, THD+N = 1% (QFN package) 8
Output Power (RL=16Ω) PO 33 mW Stereo RL = 16Ω, DAC Input, CPVVDD = 1.8V, f=1020Hz, 22kHz BW, THD+N = 1% (QFN Package) 8
Total Harmonic Distortion + Noise THD+N -88 dB RL = 32Ω, f=1020Hz, PO = 20mW 8
Signal to Noise Ratio SNR 105 dB VOUT = 1VRMS, DAC Input, DAC_Gain = 0dB, HP_Gain = 0dB, Digital Zero Input, f=1020Hz, A-Weighted 8
Signal to Noise Ratio (auto attenuate) SNR 108 dB VOUT = 1 VRMS, DAC Input, DAC_Gain = 0dB, HP_Gain = 0dB, Digital Zero Input, f=1020Hz, A-Weighted, auto attenuate enabled 8
Power Supply Rejection Ratio (HP) PSRR 85 dB fRIPPLE = 217Hz, VRIPPLE = 200mVP_P Input Referred, HP_GAIN = 0dB DAC Input, DAC_Gain = 0dB Ripple Applied to VDDA 8
Channel Crosstalk XTALK 70 dB Left Channel to Right Channel, -1dBFS, Gain = 0dB, f = 1020Hz 8
Interchannel Level Mismatch -0.1 0.1 dB 8
Frequency Response (HP) -0.2 0.1 dB F = 20Hz ~ 20kHz 8
Output Noise eOS 4.4 µVRMS DAC_Gain = 0dB, HP_Gain = 0dB, fS=48kHz, OSRDAC = 128, A-Weighted 8
Out of Band Noise Level -60 dB 8
Output Offset Voltage VOS -1 1 mV HP_Gain = 0dB, DAC_Gain= 0dB, DAC Input 8
Power Consumption MP3 Mode 6 mW No Load, No Signal, Amp on fS = 48kHz, Stereo DAC On, Amp On, POUT = 0mW. RL = 32Ω 8
Fs Accuracy (44.1 / 48 kHz) -0.02 0.02 % 8
Pop and Click Noise 1 mVrms 9
ADC Total Harmonic Distortion + Noise (MIC_GAIN 0dB) THD+N -91 dB MIC Input, MIC_GAIN = 0dB, VIN = 0.8Vrms, f=1020Hz, fs = 48KHz, Mono Differential Input 9
ADC Total Harmonic Distortion + Noise (MIC_GAIN 30dB) THD+N -80 dB MIC Input, MIC_GAIN = 30dB, Volume = 0dB, Vin=28.5mVrms, f=1020Hz, Digital Gain = 0dB, Mono Differential Input 9
ADC Signal to Noise Ratio (MIC Gain 0dB) SNR 102 dB Reference = VOUT(0dBFS), A-Weighted, MIC Input, MIC Gain = 0dB,fs = 48kHz, Mono Differential Input 9
ADC Signal to Noise Ratio (MIC Gain 6dB) SNR 101 dB Reference = VOUT(0dBFS), A-Weighted, MIC Input, MIC Gain = 6dB,fs = 48kHz, Mono Differential Input 9
ADC Power Supply Rejection Ratio PSRR 80 dB VRIPPLE = 200mVPP applied to VDDA, fRIPPLE = 217Hz, Input Referred, MIC_GAIN = 0dB Differential Input 9
Common Mode Rejection Ratio CMRR 65 dB Differential Input 100mVrms, PGA gain = 20dB, frequency sweep from 20Hz to 20KHz 9
ADC Full Scale Input Level FSADC 1 VRMS VDDA= 1.8V, ADC VREFSEL = 01'b, DGAINR_ADC = DGAINL_ADC = D0'b Differential Input 9
Minimum Input Impedance 10 kOhm 9
ADC Frequency Response -0.2 0.1 dB f = 20Hz ~ 20kHz 9
ADC Power Consumption 5 mW No Signal, ADC on fs = 44.1kHz 9
MICBIAS Output Voltage VBIAS 2.5 V Programmable 1.8V to 3.0V in 6 steps 9
MICBIAS Output Current IOUT 27 mA 9
MICBIAS Output Noise eos 47 nV/√Hz Low noise mode, at 1kHz 9
Digital Supply Voltage (VDDB) Recommended Range VDDB 1.62 3.3 3.6 V Digital I/O Supply Range 10
Analog Supply Voltage (VDDA) Recommended Range VDDA 1.62 1.8 1.98 V Analog Supply Range 10
Headphone Supply Voltage (VDDA) Recommended Range VDDA 1.62 1.8 1.98 V Headphone Supply Range 10
Microphone Bias Supply Voltage (VDDMIC) VDDMIC 3 3.3 3.6 V Microphone Bias Supply Voltage 10
Temperature Range TA -40 85 °C 10
Digital Supply Range (Absolute Maximum) -0.3 2.2 V Digital Supply Range 10
Digital I/O Supply Range (Absolute Maximum) -0.3 4 V Digital I/O Supply Range 10
Analog Supply Range (Absolute Maximum) -0.3 2.2 V Analog Supply Range 10
Headphone Supply Range (Absolute Maximum) -0.3 2.2 V Headphone Supply Range 10
Microphone Bias Supply Voltage (Absolute Maximum) -0.3 4 V Microphone Bias Supply Voltage 10
Junction Temperature TJ -40 150 °C 10
Storage Temperature -65 150 °C 10

CAD (KiCad official)

  • Symbol: NAU88L21YG
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: nau88l21yg-etched.step / nau88l21yg-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); nau88l21yg.step / nau88l21yg.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Nuvoton Tech datasheet (80 pp, sha256 cea58f259542512b, retrieved 2026-11-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF