main
History Download
Ray Publish 0.1.1 a8b8057

MT88L70AS1

Microchip Tech · Telecommunication Interface ICs · SOIC-18-300mil

MT88L70AS1 from Microchip Tech, in a SOIC-18-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN+ input Non-inverting input of the front-end differential op-amp; in single-ended use it is biased at mid-rail by VRef, with 10 MΩ input resistance at 1 kHz.
2 IN- input Inverting input of the front-end differential op-amp, used with a feedback resistor from GS to set gain in differential configurations.
3 GS output Output of the front-end gain-setting op-amp, accessed for the feedback resistor; maximum capacitive load 100 pF and resistive load 50 kΩ.
4 VRef power_in Reference voltage output, nominally VDD/2 (0.5 VDD) used to bias the inputs at mid-rail; output resistance 1 kΩ.
5 INH input Inhibit input; logic high inhibits detection of tones representing characters A, B, C and D, and is internally pulled down.
6 PWDN input Active-high power-down input that powers down the device and stops the oscillator; internally pulled down.
7 OSC1 input Clock input; a 3.579545 MHz crystal is connected between OSC1 and OSC2 to complete the internal oscillator.
8 OSC2 output Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the oscillator, with a 15 pF maximum capacitive load.
9 VSS power_in Ground reference, 0 V typical.
10 TOE input Three-state output enable; logic high enables outputs Q1-Q4 and logic low forces them to high impedance; pulled up internally.
11 Q1 tri_state Three-state data output (bit 1 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low.
12 Q2 tri_state Three-state data output (bit 2 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low.
13 Q3 tri_state Three-state data output (bit 3 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low.
14 Q4 tri_state Three-state data output (bit 4 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low.
15 StD output Delayed steering output; logic high when a received tone pair has been registered and the output latch updated, returning low when St/GT falls below VTSt.
16 ESt output Early steering output; logic high once a valid tone pair is detected, and returns to logic low on any momentary loss of the signal condition.
17 St/GT bidirectional Steering input/guard time output; a voltage above VTSt (0.465 VDD typical) at St registers the tone pair, and GT drives the external RC steering time constant.
18 VDD power_in Positive power supply, +3 V typical; recommended operating range 2.7 V to 3.6 V and absolute maximum 7 V.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-18-300mil
Category Interface ICs
Pins 18

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
DC Power Supply Voltage VDD 7 V 8
Current at any pin (other than supply) II 10 mA 8
Storage temperature TSTG -65 150 °C 8
Package power dissipation PD 500 mW 8
DC Power Supply Voltage VDD 2.7 3 3.6 V 8
Operating Temperature TO -40 85 °C 8
Crystal/Clock Freq. Tolerance ∆fc -0.1 0.1 % 8
Operating supply current IDD 2 5.5 mA 8
Standby supply current IDDQ 1 10 µA PWDN=VDD 8
Power consumption PO 6 mW fc=3.579545 MHz 8
High level input voltage VIH 2.1 V VDD = 3.0 V 8
Low level input voltage VIL 0.9 V VDD = 3.0 V 8
Input leakage current IIH/IIL 0.05 5 µA VIN = VSS or VDD 8
Pull up (source) current ISO 4 15 µA TOE (pin 10) = 0, VDD = 3.0 V 8
Pull down (sink) current ISI 15 40 µA INH = VDD, PWDN = VDD, VDD = 3.0 V 8
Output low (sink) current IOL 1.5 8 mA VOUT = 0.4 V 9
Output high (source) current IOH 1 3 mA VOUT = 3.6 V, VDD = 3.6 V 9
VRef output resistance ROR 1 kΩ 9
Input leakage current (gain setting amplifier) IIN 100 nA VSS ≤ VIN ≤ VDD 9
Input offset voltage VOS 25 mV 9
Power supply rejection PSRR 50 dB 1 kHz 9
Common mode rejection CMRR 40 dB VSS + 0.75 V ≤ VIN ≤ VDD-0.75 biased at VRef =1.5 V 9
DC open loop voltage gain AVOL 32 dB 9
Output voltage swing VO 2.2 Vpp Load ≥ 100 kΩ to VSS @ GS 9
Maximum capacitive load (GS) CL 100 pF 9
Resistive load (GS) RL 50 kΩ 9
Common mode range VCM 1.5 Vpp No Load 9
Valid input signal level (each tone of composite signal) -34 -4 dBm 10
Valid input signal level (each tone of composite signal) 15.4 489 mVRMS Min @ VDD=3.6 V (min); Max @ VDD=2.7 V (max) 10
Negative twist accept 8 dB 10
Positive twist accept 8 dB 10
Frequency deviation accept -1.5 1.5 % 10
Frequency deviation accept (absolute) -2 2 Hz 10
Frequency deviation reject -3.5 3.5 % 10
Third zone tolerance -16 dB 10
Noise tolerance -12 dB 10
Dial zone tolerance 22 dB 10
Tone present detect time tDP 5 11 14 ms Note 1 11
Tone absent detect time tDA 0.5 4 8.5 ms Note 1 11
Tone duration accept tREC 40 ms Note 2 11
Tone duration reject tREC 20 ms Note 2 11
Interdigit pause accept tID 40 ms Note 2 11
Interdigit pause reject tDO 20 ms Note 2 11
Propagation delay (St to Q) tPQ 11 µs TOE=VDD 11
Propagation delay (St to StD) tPStD 20 µs TOE=VDD 11
Output data set up (Q to StD) tQStD 5 µs TOE=VDD 11
Propagation delay (TOE to Q ENABLE) tPTE 50 ns load of 10 kΩ, 50 pF 11
Propagation delay (TOE to Q DISABLE) tPTD 130 ns load of 10 kΩ, 50 pF 11
Power-up time tPU 30 ms Note 3 11
Power-down time tPD 20 ms 11
Crystal/clock frequency fC 3.5759 3.5795 3.5831 MHz 11
Clock input rise time tLHCL 110 ns Ext. clock 11
Clock input fall time tHLCL 110 ns Ext. clock 11
Clock input duty cycle DCCL 40 50 60 % Ext. clock 11
Capacitive load (OSC2) CLO 15 pF 11
Input impedance (IN+, IN-) RIN 10 MΩ @ 1 kHz 8
Input resistance (gain setting amplifier) RIN 10 MΩ 9
Unity gain bandwidth fC 0.3 MHz 9

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin MT88L70ASR1 18 Pin SOIC* Tape & Reel * Pb Free Matte Tin 1

CAD (KiCad official)

  • Symbol: MT88L70AS1
  • Footprint: Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm
  • 3D model: SOIC-18-300mil (KiCad packages3D, STEP)
  • 3D model files: mt88l70as1-etched.step / mt88l70as1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mt88l70as1.step / mt88l70as1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (16 pp, sha256 d0f63e39dba95a76, retrieved 2026-11-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF