← Commit history
README.md+49−35
@@ -8,24 +8,24 @@ MT88L70AS1 from Microchip Tech, in a SOIC-18-300mil. Pinout and pin descriptions  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | IN+ | input | Non-inverting input of the front-end differential op-amp. |-| 2 | IN- | input | Inverting input of the front-end differential op-amp. |-| 3 | GS | output | Gain Select; gives access to the output of the front-end differential amplifier for connection of a feedback resistor. |-| 4 | VRef | power_in | Reference voltage output, nominally VDD/2, used to bias inputs at mid-rail. |-| 5 | INH | input | Inhibit input; logic high inhibits detection of tones for characters A, B, C and D, and the pin is internally pulled down. |-| 6 | PWDN | input | Active-high power down input that powers down the device and inhibits the oscillator; internally pulled down. |-| 7 | OSC1 | input | Clock input; a 3.579545 MHz crystal connects between OSC1 and OSC2. |-| 8 | OSC2 | output | Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the internal oscillator circuit. |-| 9 | VSS | power_in | Ground, 0 V typical. |-| 10 | TOE | input | Three-state output enable; logic high enables outputs Q1-Q4, and the pin is pulled up internally. |-| 11 | Q1 | tri_state | Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low. |-| 12 | Q2 | tri_state | Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low. |-| 13 | Q3 | tri_state | Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low. |-| 14 | Q4 | tri_state | Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low. |-| 15 | StD | output | Delayed steering output; goes high when a tone-pair has been registered and the latch updated, returning low when St/GT falls below VTSt. |-| 16 | ESt | output | Early steering output; goes high once the digital algorithm detects a valid tone pair and returns low on any momentary loss of signal condition. |-| 17 | St/GT | bidirectional | Steering input/guard time output; a voltage above VTSt at St registers the tone pair and updates the output latch, below VTSt frees the device to accept a new tone pair. |-| 18 | VDD | power_in | Positive power supply, +3 V typical (2.7 V to 3.6 V recommended operating range). |+| 1 | IN+ | input | Non-inverting input of the front-end differential op-amp; in single-ended use it is biased at mid-rail by VRef, with 10 MΩ input resistance at 1 kHz. |+| 2 | IN- | input | Inverting input of the front-end differential op-amp, used with a feedback resistor from GS to set gain in differential configurations. |+| 3 | GS | output | Output of the front-end gain-setting op-amp, accessed for the feedback resistor; maximum capacitive load 100 pF and resistive load 50 kΩ. |+| 4 | VRef | power_in | Reference voltage output, nominally VDD/2 (0.5 VDD) used to bias the inputs at mid-rail; output resistance 1 kΩ. |+| 5 | INH | input | Inhibit input; logic high inhibits detection of tones representing characters A, B, C and D, and is internally pulled down. |+| 6 | PWDN | input | Active-high power-down input that powers down the device and stops the oscillator; internally pulled down. |+| 7 | OSC1 | input | Clock input; a 3.579545 MHz crystal is connected between OSC1 and OSC2 to complete the internal oscillator. |+| 8 | OSC2 | output | Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the oscillator, with a 15 pF maximum capacitive load. |+| 9 | VSS | power_in | Ground reference, 0 V typical. |+| 10 | TOE | input | Three-state output enable; logic high enables outputs Q1-Q4 and logic low forces them to high impedance; pulled up internally. |+| 11 | Q1 | tri_state | Three-state data output (bit 1 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |+| 12 | Q2 | tri_state | Three-state data output (bit 2 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |+| 13 | Q3 | tri_state | Three-state data output (bit 3 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |+| 14 | Q4 | tri_state | Three-state data output (bit 4 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |+| 15 | StD | output | Delayed steering output; logic high when a received tone pair has been registered and the output latch updated, returning low when St/GT falls below VTSt. |+| 16 | ESt | output | Early steering output; logic high once a valid tone pair is detected, and returns to logic low on any momentary loss of the signal condition. |+| 17 | St/GT | bidirectional | Steering input/guard time output; a voltage above VTSt (0.465 VDD typical) at St registers the tone pair, and GT drives the external RC steering time constant. |+| 18 | VDD | power_in | Positive power supply, +3 V typical; recommended operating range 2.7 V to 3.6 V and absolute maximum 7 V. |  ## Key specifications @@ -42,32 +42,43 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| DC Power Supply Voltage | VDD | 2.7 | 3 | 3.6 | V |  | 8 |-| Operating Temperature | TO | -40 |  | 85 | °C |  | 8 |-| Crystal/Clock Frequency | fc |  | 3.57954 |  | MHz |  | 8 |-| Crystal/Clock Freq. Tolerance | ∆fc | -0.1 |  | 0.1 | % |  | 8 |-| DC Power Supply Voltage (absolute maximum) | VDD |  |  | 7 | V |  | 8 |+| DC Power Supply Voltage | VDD |  |  | 7 | V |  | 8 | | Current at any pin (other than supply) | II |  |  | 10 | mA |  | 8 | | Storage temperature | TSTG | -65 |  | 150 | °C |  | 8 | | Package power dissipation | PD |  |  | 500 | mW |  | 8 |-| Standby supply current | IDDQ |  | 1 | 10 | µA | PWDN=VDD | 8 |-| Operating supply current | IDD |  | 2 | 5.5 | mA |  | 8 |-| Power consumption | PO |  | 6 |  | mW | fc=3.579545 MHz | 8 |+| DC Power Supply Voltage | VDD | 2.7 | 3 | 3.6 | V |  | 8 |+| Operating Temperature | TO | -40 |  | 85 | °C |  | 8 |+| Crystal/Clock Freq. Tolerance | ∆fc | -0.1 |  | 0.1 | % |  | 8 |+| Operating supply current | IDD | 2 |  | 5.5 | mA |  | 8 |+| Standby supply current | IDDQ | 1 |  | 10 | µA | PWDN=VDD | 8 |+| Power consumption | PO |  |  | 6 | mW | fc=3.579545 MHz | 8 | | High level input voltage | VIH | 2.1 |  |  | V | VDD = 3.0 V | 8 | | Low level input voltage | VIL |  |  | 0.9 | V | VDD = 3.0 V | 8 |-| Input leakage current | IIH/IIL |  | 0.05 | 5 | µA | VIN = VSS or VDD | 8 |+| Input leakage current | IIH/IIL | 0.05 |  | 5 | µA | VIN = VSS or VDD | 8 | | Pull up (source) current | ISO | 4 |  | 15 | µA | TOE (pin 10) = 0, VDD = 3.0 V | 8 | | Pull down (sink) current | ISI | 15 |  | 40 | µA | INH = VDD, PWDN = VDD, VDD = 3.0 V | 8 |-| Input impedance (IN+, IN-) | RIN |  | 10 |  | MΩ | @ 1 kHz | 8 | | Output low (sink) current | IOL | 1.5 |  | 8 | mA | VOUT = 0.4 V | 9 | | Output high (source) current | IOH | 1 |  | 3 | mA | VOUT = 3.6 V, VDD = 3.6 V | 9 |-| VRef output resistance | ROR |  | 1 |  | kΩ |  | 9 |-| Input offset voltage | VOS |  |  | 25 | mV |  | 9 |-| Input resistance | RIN |  | 10 |  | MΩ |  | 9 |+| VRef output resistance | ROR |  |  | 1 | kΩ |  | 9 | | Input leakage current (gain setting amplifier) | IIN |  |  | 100 | nA | VSS ≤ VIN ≤ VDD | 9 |-| Unity gain bandwidth | fC |  | 0.3 |  | MHz |  | 9 |+| Input offset voltage | VOS |  |  | 25 | mV |  | 9 |+| Power supply rejection | PSRR | 50 |  |  | dB | 1 kHz | 9 |+| Common mode rejection | CMRR | 40 |  |  | dB | VSS + 0.75 V ≤ VIN ≤ VDD-0.75 biased at VRef =1.5 V | 9 |+| DC open loop voltage gain | AVOL | 32 |  |  | dB |  | 9 |+| Output voltage swing | VO | 2.2 |  |  | Vpp | Load ≥ 100 kΩ to VSS @ GS | 9 | | Maximum capacitive load (GS) | CL |  |  | 100 | pF |  | 9 |-| Resistive load (GS) | RL |  |  | 50 | kΩ |  | 9 |+| Resistive load (GS) | RL | 50 |  |  | kΩ |  | 9 |+| Common mode range | VCM | 1.5 |  |  | Vpp | No Load | 9 |+| Valid input signal level (each tone of composite signal) |  | -34 |  | -4 | dBm |  | 10 |+| Valid input signal level (each tone of composite signal) |  | 15.4 |  | 489 | mVRMS | Min @ VDD=3.6 V (min); Max @ VDD=2.7 V (max) | 10 |+| Negative twist accept |  | 8 |  |  | dB |  | 10 |+| Positive twist accept |  | 8 |  |  | dB |  | 10 |+| Frequency deviation accept |  | -1.5 |  | 1.5 | % |  | 10 |+| Frequency deviation accept (absolute) |  | -2 |  | 2 | Hz |  | 10 |+| Frequency deviation reject |  | -3.5 |  | 3.5 | % |  | 10 |+| Third zone tolerance |  |  |  | -16 | dB |  | 10 |+| Noise tolerance |  |  |  | -12 | dB |  | 10 |+| Dial zone tolerance |  | 22 |  |  | dB |  | 10 | | Tone present detect time | tDP | 5 | 11 | 14 | ms | Note 1 | 11 | | Tone absent detect time | tDA | 0.5 | 4 | 8.5 | ms | Note 1 | 11 | | Tone duration accept | tREC | 40 |  |  | ms | Note 2 | 11 |@@ -86,6 +97,9 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries | Clock input fall time | tHLCL |  |  | 110 | ns | Ext. clock | 11 | | Clock input duty cycle | DCCL | 40 | 50 | 60 | % | Ext. clock | 11 | | Capacitive load (OSC2) | CLO |  |  | 15 | pF |  | 11 |+| Input impedance (IN+, IN-) | RIN |  | 10 |  | MΩ | @ 1 kHz | 8 |+| Input resistance (gain setting amplifier) | RIN |  | 10 |  | MΩ |  | 9 |+| Unity gain bandwidth | fC |  | 0.3 |  | MHz |  | 9 |  ## Materials and finish @@ -106,8 +120,8 @@ As the datasheet states them (page.json `metadata.appearance`; the 3D model's co  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Microchip Tech datasheet](docs/mt88l70as1-datasheet.pdf) (16 pp, sha256 `d0f63e39dba95a76`, retrieved 2026-11-10, tier: lcsc)-- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **Datasheet:** [Microchip Tech datasheet](docs/mt88l70as1-datasheet.pdf) (16 pp, sha256 `d0f63e39dba95a76`, retrieved 2026-11-11, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0).  [Datasheet PDF](docs/mt88l70as1-datasheet.pdf)
mt88l70as1-hero.overlay.json+480−478
@@ -1,480 +1,482 @@ {-  "spec": "adom-hero 1.4",-  "mpn": "MT88L70AS1",-  "kind": "component + footprint reference art",-  "board_use": false,-  "plane_z_mm": -0.02,-  "units": "metre",-  "upAxis": "Z",-  "layers": {-    "pad_outlines": {-      "material": "Footprint pads - teal dashed outlines - 50 percent opacity",-      "rgba": [-        0.0,-        0.902,-        0.863,-        0.5-      ],-      "pads": 18,-      "span_mm": 11.35,-      "dash_mm": 0.2838,-      "gap_mm": 0.1703,-      "pad_stroke_mm": 0.0681-    },-    "silkscreen": {-      "material": "Silkscreen reference lines - 30 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.3-      ],-      "footprint_items": 7,-      "pin1": {-        "source": "footprint silkscreen",-        "pad": "1"-      }-    },-    "signal_names": {-      "material": "Signal names - 50 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.5-      ],-      "font": "DejaVu Sans Mono",-      "labels": 18,-      "sides": "top + mirrored underside (single-sided)",-      "fallback_to_pad_number": 0-    }-  },-  "align": {-    "ok": true,-    "centre_offset_mm": 0.0,-    "tolerance_mm": 0.908,-    "orientation_flipped": false,-    "contacts_bbox_mm": [-      -5.15,-      5.15,-      -5.285,-      5.285-    ],-    "pads_bbox_mm": [-      -5.675,-      5.675,-      -5.38,-      5.38-    ],-    "seating_z_mm": 0.0-  },-  "sources": {-    "glb": "mt88l70as1-etched.glb",-    "glb_sha256": "e51d1d0112b1abeedf7083172e3f3e7df3bec5974e399d13c1413f4a2d75cc95",-    "footprint": "mt88l70as1.kicad_mod",-    "footprint_sha256": "7eec490ec4feabbe30fa197f0f395da5eeabbd36efadacce0a3f05290c8be447",-    "pins": "page.json component.pins",-    "pins_sha256": "0cd488b91a1e070f1c69a03cb76d2c1a9851019def317dae55ea32ac2ececf5f"-  },-  "generator": "adom-wiki 1.8.15 (component_hero)",-  "labels": [-    {-      "pad": "1",-      "text": "IN+",-      "x": -5.825,-      "y": -5.08,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "2",-      "text": "IN-",-      "x": -5.825,-      "y": -3.81,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "3",-      "text": "GS",-      "x": -5.825,-      "y": -2.54,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "4",-      "text": "VRef",-      "x": -5.825,-      "y": -1.27,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "5",-      "text": "INH",-      "x": -5.825,-      "y": 0.0,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "6",-      "text": "PWDN",-      "x": -5.825,-      "y": 1.27,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "7",-      "text": "OSC1",-      "x": -5.825,-      "y": 2.54,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "8",-      "text": "OSC2",-      "x": -5.825,-      "y": 3.81,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "9",-      "text": "VSS",-      "x": -5.825,-      "y": 5.08,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "10",-      "text": "TOE",-      "x": 5.825,-      "y": 5.08,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "11",-      "text": "Q1",-      "x": 5.825,-      "y": 3.81,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "12",-      "text": "Q2",-      "x": 5.825,-      "y": 2.54,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "13",-      "text": "Q3",-      "x": 5.825,-      "y": 1.27,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "14",-      "text": "Q4",-      "x": 5.825,-      "y": 0.0,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "15",-      "text": "StD",-      "x": 5.825,-      "y": -1.27,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "16",-      "text": "ESt",-      "x": 5.825,-      "y": -2.54,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "17",-      "text": "St/GT",-      "x": 5.825,-      "y": -3.81,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "18",-      "text": "VDD",-      "x": 5.825,-      "y": -5.08,-      "align": "left",-      "vertical": false,-      "h": 0.6-    }+ "spec": "adom-hero 1.4",+ "mpn": "MT88L70AS1",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+  "pad_outlines": {+   "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+   "rgba": [+    0.0,+    0.902,+    0.863,+    0.5+   ],+   "pads": 18,+   "span_mm": 11.35,+   "dash_mm": 0.2838,+   "gap_mm": 0.1703,+   "pad_stroke_mm": 0.0681+  },+  "silkscreen": {+   "material": "Silkscreen reference lines - 30 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.3+   ],+   "footprint_items": 7,+   "pin1": {+    "source": "footprint silkscreen",+    "pad": "1"+   }+  },+  "signal_names": {+   "material": "Signal names - 50 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.5+   ],+   "font": "DejaVu Sans Mono",+   "labels": 18,+   "sides": "top + mirrored underside (single-sided)",+   "omitted": null,+   "fallback_to_pad_number": 0+  }+ },+ "align": {+  "ok": true,+  "centre_offset_mm": 0.0,+  "over_pads": true,+  "tolerance_mm": 0.908,+  "orientation_flipped": false,+  "contacts_bbox_mm": [+   -5.15,+   5.15,+   -5.285,+   5.285+  ],+  "pads_bbox_mm": [+   -5.675,+   5.675,+   -5.38,+   5.38   ],-  "pads": [-    {-      "number": "1",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -5.08-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "2",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -3.81-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "3",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -2.54-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "4",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -1.27-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "5",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        0.0-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "6",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        1.27-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "7",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        2.54-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "8",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        3.81-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "9",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        5.08-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "10",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        5.08-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "11",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        3.81-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "12",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        2.54-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "13",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        1.27-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "14",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        0.0-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "15",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -1.27-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "16",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -2.54-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "17",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -3.81-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "18",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -5.08-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    }-  ]-}+  "seating_z_mm": 0.0+ },+ "sources": {+  "glb": "mt88l70as1-etched.glb",+  "glb_sha256": "e51d1d0112b1abeedf7083172e3f3e7df3bec5974e399d13c1413f4a2d75cc95",+  "footprint": "mt88l70as1.kicad_mod",+  "footprint_sha256": "7eec490ec4feabbe30fa197f0f395da5eeabbd36efadacce0a3f05290c8be447",+  "pins": "page.json component.pins",+  "pins_sha256": "0cd488b91a1e070f1c69a03cb76d2c1a9851019def317dae55ea32ac2ececf5f"+ },+ "generator": "factory/hero_glb.py",+ "labels": [+  {+   "pad": "1",+   "text": "IN+",+   "x": -5.825,+   "y": -5.08,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "2",+   "text": "IN-",+   "x": -5.825,+   "y": -3.81,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "3",+   "text": "GS",+   "x": -5.825,+   "y": -2.54,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "4",+   "text": "VRef",+   "x": -5.825,+   "y": -1.27,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "5",+   "text": "INH",+   "x": -5.825,+   "y": 0.0,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "6",+   "text": "PWDN",+   "x": -5.825,+   "y": 1.27,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "7",+   "text": "OSC1",+   "x": -5.825,+   "y": 2.54,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "8",+   "text": "OSC2",+   "x": -5.825,+   "y": 3.81,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "9",+   "text": "VSS",+   "x": -5.825,+   "y": 5.08,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "10",+   "text": "TOE",+   "x": 5.825,+   "y": 5.08,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "11",+   "text": "Q1",+   "x": 5.825,+   "y": 3.81,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "12",+   "text": "Q2",+   "x": 5.825,+   "y": 2.54,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "13",+   "text": "Q3",+   "x": 5.825,+   "y": 1.27,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "14",+   "text": "Q4",+   "x": 5.825,+   "y": 0.0,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "15",+   "text": "StD",+   "x": 5.825,+   "y": -1.27,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "16",+   "text": "ESt",+   "x": 5.825,+   "y": -2.54,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "17",+   "text": "St/GT",+   "x": 5.825,+   "y": -3.81,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "18",+   "text": "VDD",+   "x": 5.825,+   "y": -5.08,+   "align": "left",+   "vertical": false,+   "h": 0.6+  }+ ],+ "pads": [+  {+   "number": "1",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -5.08+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -3.81+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "3",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -2.54+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "4",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -1.27+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "5",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    0.0+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "6",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    1.27+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "7",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    2.54+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "8",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    3.81+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "9",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    5.08+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "10",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    5.08+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "11",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    3.81+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "12",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    2.54+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "13",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    1.27+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "14",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    0.0+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "15",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -1.27+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "16",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -2.54+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "17",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -3.81+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "18",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -5.08+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  }+ ]+}\ No newline at end of file
mt88l70as1.lbr+14−3
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>Microchip Tech Telecommunication Interface ICs, SOIC-18-300mil. Pinout cross-checked by two models against the datasheet</description> <packages> <package name="SOIC-18W_7.5x11.6mm_P1.27mm">   <description>SOIC-18W, 7.5 x 11.6 mm, 1.27 mm pitch. SOIC, 18 Pin</description>@@ -96,6 +96,7 @@ </packages> <symbols> <symbol name="MT88L70AS1">+  <description>Microchip Tech Telecommunication Interface ICs, SOIC-18-300mil. Pinout cross-checked by two models against the datasheet</description>   <wire x1="-12.7" y1="12.7" x2="12.7" y2="12.7" width="0.254" layer="94"/>   <wire x1="12.7" y1="12.7" x2="12.7" y2="-12.7" width="0.254" layer="94"/>   <wire x1="12.7" y1="-12.7" x2="-12.7" y2="-12.7" width="0.254" layer="94"/>@@ -124,7 +125,7 @@ </symbols> <devicesets> <deviceset name="MT88L70AS1" prefix="U">-  <description></description>+  <description>Microchip Tech Telecommunication Interface ICs, SOIC-18-300mil. Pinout cross-checked by two models against the datasheet</description>   <gates>     <gate name="G$1" symbol="MT88L70AS1" x="0" y="0"/>   </gates>@@ -150,7 +151,17 @@         <connect gate="G$1" pin="Q1" pad="11"/>         <connect gate="G$1" pin="TOE" pad="10"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="MT88L70AS1" constant="no"/>+          <attribute name="MANUFACTURER" value="Microchip Tech" constant="no"/>+          <attribute name="DATASHEET" value="https://datasheet.lcsc.com/datasheet/pdf/3887be22f9535dea628375e8b379c904.pdf" constant="no"/>+          <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/mt88l70as1" constant="no"/>+          <attribute name="MOUSER_PN" value="494-MT88L70AS1" constant="no"/>+          <attribute name="DIGIKEY_PN" value="MT88L70AS1-ND" constant="no"/>+          <attribute name="LCSC_PN" value="C1522215" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>
package.json+29−27
@@ -1,6 +1,6 @@ {   "slug": "mt88l70as1",-  "version": "0.1.0",+  "version": "0.1.1",   "type": "component",   "description": "Microchip Tech Telecommunication Interface ICs, SOIC-18-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -54,7 +54,7 @@       "mouser": "494-MT88L70AS1"     },     "distributor_check": {-      "checked_at": "2026-11-10T01:12:27Z",+      "checked_at": "2026-11-11T00:57:47Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "MT88L70AS1-ND",@@ -70,109 +70,109 @@         "number": "1",         "name": "IN+",         "type": "input",-        "description": "Non-inverting input of the front-end differential op-amp."+        "description": "Non-inverting input of the front-end differential op-amp; in single-ended use it is biased at mid-rail by VRef, with 10 MΩ input resistance at 1 kHz."       },       {         "number": "2",         "name": "IN-",         "type": "input",-        "description": "Inverting input of the front-end differential op-amp."+        "description": "Inverting input of the front-end differential op-amp, used with a feedback resistor from GS to set gain in differential configurations."       },       {         "number": "3",         "name": "GS",         "type": "output",-        "description": "Gain Select; gives access to the output of the front-end differential amplifier for connection of a feedback resistor."+        "description": "Output of the front-end gain-setting op-amp, accessed for the feedback resistor; maximum capacitive load 100 pF and resistive load 50 kΩ."       },       {         "number": "4",         "name": "VRef",         "type": "power_in",-        "description": "Reference voltage output, nominally VDD/2, used to bias inputs at mid-rail."+        "description": "Reference voltage output, nominally VDD/2 (0.5 VDD) used to bias the inputs at mid-rail; output resistance 1 kΩ."       },       {         "number": "5",         "name": "INH",         "type": "input",-        "description": "Inhibit input; logic high inhibits detection of tones for characters A, B, C and D, and the pin is internally pulled down."+        "description": "Inhibit input; logic high inhibits detection of tones representing characters A, B, C and D, and is internally pulled down."       },       {         "number": "6",         "name": "PWDN",         "type": "input",-        "description": "Active-high power down input that powers down the device and inhibits the oscillator; internally pulled down."+        "description": "Active-high power-down input that powers down the device and stops the oscillator; internally pulled down."       },       {         "number": "7",         "name": "OSC1",         "type": "input",-        "description": "Clock input; a 3.579545 MHz crystal connects between OSC1 and OSC2."+        "description": "Clock input; a 3.579545 MHz crystal is connected between OSC1 and OSC2 to complete the internal oscillator."       },       {         "number": "8",         "name": "OSC2",         "type": "output",-        "description": "Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the internal oscillator circuit."+        "description": "Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the oscillator, with a 15 pF maximum capacitive load."       },       {         "number": "9",         "name": "VSS",         "type": "power_in",-        "description": "Ground, 0 V typical."+        "description": "Ground reference, 0 V typical."       },       {         "number": "10",         "name": "TOE",         "type": "input",-        "description": "Three-state output enable; logic high enables outputs Q1-Q4, and the pin is pulled up internally."+        "description": "Three-state output enable; logic high enables outputs Q1-Q4 and logic low forces them to high impedance; pulled up internally."       },       {         "number": "11",         "name": "Q1",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 1 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "12",         "name": "Q2",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 2 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "13",         "name": "Q3",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 3 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "14",         "name": "Q4",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 4 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "15",         "name": "StD",         "type": "output",-        "description": "Delayed steering output; goes high when a tone-pair has been registered and the latch updated, returning low when St/GT falls below VTSt."+        "description": "Delayed steering output; logic high when a received tone pair has been registered and the output latch updated, returning low when St/GT falls below VTSt."       },       {         "number": "16",         "name": "ESt",         "type": "output",-        "description": "Early steering output; goes high once the digital algorithm detects a valid tone pair and returns low on any momentary loss of signal condition."+        "description": "Early steering output; logic high once a valid tone pair is detected, and returns to logic low on any momentary loss of the signal condition."       },       {         "number": "17",         "name": "St/GT",         "type": "bidirectional",-        "description": "Steering input/guard time output; a voltage above VTSt at St registers the tone pair and updates the output latch, below VTSt frees the device to accept a new tone pair."+        "description": "Steering input/guard time output; a voltage above VTSt (0.465 VDD typical) at St registers the tone pair, and GT drives the external RC steering time constant."       },       {         "number": "18",         "name": "VDD",         "type": "power_in",-        "description": "Positive power supply, +3 V typical (2.7 V to 3.6 V recommended operating range)."+        "description": "Positive power supply, +3 V typical; recommended operating range 2.7 V to 3.6 V and absolute maximum 7 V."       }     ],     "provenance": {@@ -180,15 +180,17 @@       "factory_chain": {         "factory": "2.0.0",         "extractor": "extract_pins 0.3",-        "primary_model": "claude-sonnet-5-5",+        "primary_model": "claude-haiku-5-5",         "primary_mode": "text",         "consensus_model": "claude-sonnet-5-5",         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",-        "guard_notes": [],+        "guard_notes": [+          "extractor flagged: The 18-pin pin-number assignments were taken from the Pin Description table's 18-pin column (page 2); The datasheet lists 'NC' pins 7 and 16 in the table without specifying which package column they bel; The datasheet lists the MT88L70AS1 as '18 Pin SOIC* Tubes' (Pb-free) but does not state the body wid"+        ],         "pages_sent": 16,-        "cost_usd": 0.0802,-        "at": "2026-11-10T01:12:10"+        "cost_usd": 0.0678,+        "at": "2026-11-11T00:57:32"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/3887be22f9535dea628375e8b379c904.pdf",@@ -225,7 +227,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "05ad7d4945131c76ec7b9448dd9cbb5376b56adcd564c58d93e50ca7870fab1f",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -243,8 +245,8 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "f7c561b3bd20cebbf41dba31bddfb743bd698bd30f96a7cdc4b6d9e1d0ad96cf",-        "checked": "2026-11-10",+        "sha256": "51cae42931479804830fea06c2c833781721d5a00f8b924b719832d75a6488b5",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]
page.json+32−28
@@ -4,7 +4,7 @@   "slug": "mt88l70as1",   "title": "MT88L70AS1",   "brief": "Microchip Tech Telecommunication Interface ICs, SOIC-18-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.1.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -36,7 +36,7 @@       "mouser": "494-MT88L70AS1"     },     "distributor_check": {-      "checked_at": "2026-11-10T01:12:27Z",+      "checked_at": "2026-11-11T00:57:47Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "MT88L70AS1-ND",@@ -52,109 +52,109 @@         "number": "1",         "name": "IN+",         "type": "input",-        "description": "Non-inverting input of the front-end differential op-amp."+        "description": "Non-inverting input of the front-end differential op-amp; in single-ended use it is biased at mid-rail by VRef, with 10 MΩ input resistance at 1 kHz."       },       {         "number": "2",         "name": "IN-",         "type": "input",-        "description": "Inverting input of the front-end differential op-amp."+        "description": "Inverting input of the front-end differential op-amp, used with a feedback resistor from GS to set gain in differential configurations."       },       {         "number": "3",         "name": "GS",         "type": "output",-        "description": "Gain Select; gives access to the output of the front-end differential amplifier for connection of a feedback resistor."+        "description": "Output of the front-end gain-setting op-amp, accessed for the feedback resistor; maximum capacitive load 100 pF and resistive load 50 kΩ."       },       {         "number": "4",         "name": "VRef",         "type": "power_in",-        "description": "Reference voltage output, nominally VDD/2, used to bias inputs at mid-rail."+        "description": "Reference voltage output, nominally VDD/2 (0.5 VDD) used to bias the inputs at mid-rail; output resistance 1 kΩ."       },       {         "number": "5",         "name": "INH",         "type": "input",-        "description": "Inhibit input; logic high inhibits detection of tones for characters A, B, C and D, and the pin is internally pulled down."+        "description": "Inhibit input; logic high inhibits detection of tones representing characters A, B, C and D, and is internally pulled down."       },       {         "number": "6",         "name": "PWDN",         "type": "input",-        "description": "Active-high power down input that powers down the device and inhibits the oscillator; internally pulled down."+        "description": "Active-high power-down input that powers down the device and stops the oscillator; internally pulled down."       },       {         "number": "7",         "name": "OSC1",         "type": "input",-        "description": "Clock input; a 3.579545 MHz crystal connects between OSC1 and OSC2."+        "description": "Clock input; a 3.579545 MHz crystal is connected between OSC1 and OSC2 to complete the internal oscillator."       },       {         "number": "8",         "name": "OSC2",         "type": "output",-        "description": "Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the internal oscillator circuit."+        "description": "Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the oscillator, with a 15 pF maximum capacitive load."       },       {         "number": "9",         "name": "VSS",         "type": "power_in",-        "description": "Ground, 0 V typical."+        "description": "Ground reference, 0 V typical."       },       {         "number": "10",         "name": "TOE",         "type": "input",-        "description": "Three-state output enable; logic high enables outputs Q1-Q4, and the pin is pulled up internally."+        "description": "Three-state output enable; logic high enables outputs Q1-Q4 and logic low forces them to high impedance; pulled up internally."       },       {         "number": "11",         "name": "Q1",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 1 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "12",         "name": "Q2",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 2 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "13",         "name": "Q3",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 3 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "14",         "name": "Q4",         "type": "tri_state",-        "description": "Three-state data output providing the code of the last valid tone-pair when enabled by TOE, high impedance when TOE is low."+        "description": "Three-state data output (bit 4 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low."       },       {         "number": "15",         "name": "StD",         "type": "output",-        "description": "Delayed steering output; goes high when a tone-pair has been registered and the latch updated, returning low when St/GT falls below VTSt."+        "description": "Delayed steering output; logic high when a received tone pair has been registered and the output latch updated, returning low when St/GT falls below VTSt."       },       {         "number": "16",         "name": "ESt",         "type": "output",-        "description": "Early steering output; goes high once the digital algorithm detects a valid tone pair and returns low on any momentary loss of signal condition."+        "description": "Early steering output; logic high once a valid tone pair is detected, and returns to logic low on any momentary loss of the signal condition."       },       {         "number": "17",         "name": "St/GT",         "type": "bidirectional",-        "description": "Steering input/guard time output; a voltage above VTSt at St registers the tone pair and updates the output latch, below VTSt frees the device to accept a new tone pair."+        "description": "Steering input/guard time output; a voltage above VTSt (0.465 VDD typical) at St registers the tone pair, and GT drives the external RC steering time constant."       },       {         "number": "18",         "name": "VDD",         "type": "power_in",-        "description": "Positive power supply, +3 V typical (2.7 V to 3.6 V recommended operating range)."+        "description": "Positive power supply, +3 V typical; recommended operating range 2.7 V to 3.6 V and absolute maximum 7 V."       }     ],     "provenance": {@@ -162,15 +162,17 @@       "factory_chain": {         "factory": "2.0.0",         "extractor": "extract_pins 0.3",-        "primary_model": "claude-sonnet-5-5",+        "primary_model": "claude-haiku-5-5",         "primary_mode": "text",         "consensus_model": "claude-sonnet-5-5",         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",-        "guard_notes": [],+        "guard_notes": [+          "extractor flagged: The 18-pin pin-number assignments were taken from the Pin Description table's 18-pin column (page 2); The datasheet lists 'NC' pins 7 and 16 in the table without specifying which package column they bel; The datasheet lists the MT88L70AS1 as '18 Pin SOIC* Tubes' (Pb-free) but does not state the body wid"+        ],         "pages_sent": 16,-        "cost_usd": 0.0802,-        "at": "2026-11-10T01:12:10"+        "cost_usd": 0.0678,+        "at": "2026-11-11T00:57:32"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/3887be22f9535dea628375e8b379c904.pdf",@@ -207,7 +209,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "05ad7d4945131c76ec7b9448dd9cbb5376b56adcd564c58d93e50ca7870fab1f",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -225,8 +227,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "f7c561b3bd20cebbf41dba31bddfb743bd698bd30f96a7cdc4b6d9e1d0ad96cf",-        "checked": "2026-11-10",+        "sha256": "51cae42931479804830fea06c2c833781721d5a00f8b924b719832d75a6488b5",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]@@ -823,5 +825,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "Microchip Tech Telecommunication Interface ICs, SOIC-18-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file