Generated by kicad-footprint-generator · KiCad file format 20260206
MT88L70AS1
Microchip Tech · Telecommunication Interface ICs · SOIC-18-300mil
MT88L70AS1 from Microchip Tech, in a SOIC-18-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN+ | input | Non-inverting input of the front-end differential op-amp; in single-ended use it is biased at mid-rail by VRef, with 10 MΩ input resistance at 1 kHz. |
| 2 | IN- | input | Inverting input of the front-end differential op-amp, used with a feedback resistor from GS to set gain in differential configurations. |
| 3 | GS | output | Output of the front-end gain-setting op-amp, accessed for the feedback resistor; maximum capacitive load 100 pF and resistive load 50 kΩ. |
| 4 | VRef | power_in | Reference voltage output, nominally VDD/2 (0.5 VDD) used to bias the inputs at mid-rail; output resistance 1 kΩ. |
| 5 | INH | input | Inhibit input; logic high inhibits detection of tones representing characters A, B, C and D, and is internally pulled down. |
| 6 | PWDN | input | Active-high power-down input that powers down the device and stops the oscillator; internally pulled down. |
| 7 | OSC1 | input | Clock input; a 3.579545 MHz crystal is connected between OSC1 and OSC2 to complete the internal oscillator. |
| 8 | OSC2 | output | Clock output; a 3.579545 MHz crystal connected between OSC1 and OSC2 completes the oscillator, with a 15 pF maximum capacitive load. |
| 9 | VSS | power_in | Ground reference, 0 V typical. |
| 10 | TOE | input | Three-state output enable; logic high enables outputs Q1-Q4 and logic low forces them to high impedance; pulled up internally. |
| 11 | Q1 | tri_state | Three-state data output (bit 1 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |
| 12 | Q2 | tri_state | Three-state data output (bit 2 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |
| 13 | Q3 | tri_state | Three-state data output (bit 3 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |
| 14 | Q4 | tri_state | Three-state data output (bit 4 of the decoded tone code), providing the last valid tone-pair code when enabled by TOE and high impedance when TOE is low. |
| 15 | StD | output | Delayed steering output; logic high when a received tone pair has been registered and the output latch updated, returning low when St/GT falls below VTSt. |
| 16 | ESt | output | Early steering output; logic high once a valid tone pair is detected, and returns to logic low on any momentary loss of the signal condition. |
| 17 | St/GT | bidirectional | Steering input/guard time output; a voltage above VTSt (0.465 VDD typical) at St registers the tone pair, and GT drives the external RC steering time constant. |
| 18 | VDD | power_in | Positive power supply, +3 V typical; recommended operating range 2.7 V to 3.6 V and absolute maximum 7 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-18-300mil |
| Category | Interface ICs |
| Pins | 18 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DC Power Supply Voltage | VDD | 7 | V | 8 | |||
| Current at any pin (other than supply) | II | 10 | mA | 8 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 8 | ||
| Package power dissipation | PD | 500 | mW | 8 | |||
| DC Power Supply Voltage | VDD | 2.7 | 3 | 3.6 | V | 8 | |
| Operating Temperature | TO | -40 | 85 | °C | 8 | ||
| Crystal/Clock Freq. Tolerance | ∆fc | -0.1 | 0.1 | % | 8 | ||
| Operating supply current | IDD | 2 | 5.5 | mA | 8 | ||
| Standby supply current | IDDQ | 1 | 10 | µA | PWDN=VDD | 8 | |
| Power consumption | PO | 6 | mW | fc=3.579545 MHz | 8 | ||
| High level input voltage | VIH | 2.1 | V | VDD = 3.0 V | 8 | ||
| Low level input voltage | VIL | 0.9 | V | VDD = 3.0 V | 8 | ||
| Input leakage current | IIH/IIL | 0.05 | 5 | µA | VIN = VSS or VDD | 8 | |
| Pull up (source) current | ISO | 4 | 15 | µA | TOE (pin 10) = 0, VDD = 3.0 V | 8 | |
| Pull down (sink) current | ISI | 15 | 40 | µA | INH = VDD, PWDN = VDD, VDD = 3.0 V | 8 | |
| Output low (sink) current | IOL | 1.5 | 8 | mA | VOUT = 0.4 V | 9 | |
| Output high (source) current | IOH | 1 | 3 | mA | VOUT = 3.6 V, VDD = 3.6 V | 9 | |
| VRef output resistance | ROR | 1 | kΩ | 9 | |||
| Input leakage current (gain setting amplifier) | IIN | 100 | nA | VSS ≤ VIN ≤ VDD | 9 | ||
| Input offset voltage | VOS | 25 | mV | 9 | |||
| Power supply rejection | PSRR | 50 | dB | 1 kHz | 9 | ||
| Common mode rejection | CMRR | 40 | dB | VSS + 0.75 V ≤ VIN ≤ VDD-0.75 biased at VRef =1.5 V | 9 | ||
| DC open loop voltage gain | AVOL | 32 | dB | 9 | |||
| Output voltage swing | VO | 2.2 | Vpp | Load ≥ 100 kΩ to VSS @ GS | 9 | ||
| Maximum capacitive load (GS) | CL | 100 | pF | 9 | |||
| Resistive load (GS) | RL | 50 | kΩ | 9 | |||
| Common mode range | VCM | 1.5 | Vpp | No Load | 9 | ||
| Valid input signal level (each tone of composite signal) | -34 | -4 | dBm | 10 | |||
| Valid input signal level (each tone of composite signal) | 15.4 | 489 | mVRMS | Min @ VDD=3.6 V (min); Max @ VDD=2.7 V (max) | 10 | ||
| Negative twist accept | 8 | dB | 10 | ||||
| Positive twist accept | 8 | dB | 10 | ||||
| Frequency deviation accept | -1.5 | 1.5 | % | 10 | |||
| Frequency deviation accept (absolute) | -2 | 2 | Hz | 10 | |||
| Frequency deviation reject | -3.5 | 3.5 | % | 10 | |||
| Third zone tolerance | -16 | dB | 10 | ||||
| Noise tolerance | -12 | dB | 10 | ||||
| Dial zone tolerance | 22 | dB | 10 | ||||
| Tone present detect time | tDP | 5 | 11 | 14 | ms | Note 1 | 11 |
| Tone absent detect time | tDA | 0.5 | 4 | 8.5 | ms | Note 1 | 11 |
| Tone duration accept | tREC | 40 | ms | Note 2 | 11 | ||
| Tone duration reject | tREC | 20 | ms | Note 2 | 11 | ||
| Interdigit pause accept | tID | 40 | ms | Note 2 | 11 | ||
| Interdigit pause reject | tDO | 20 | ms | Note 2 | 11 | ||
| Propagation delay (St to Q) | tPQ | 11 | µs | TOE=VDD | 11 | ||
| Propagation delay (St to StD) | tPStD | 20 | µs | TOE=VDD | 11 | ||
| Output data set up (Q to StD) | tQStD | 5 | µs | TOE=VDD | 11 | ||
| Propagation delay (TOE to Q ENABLE) | tPTE | 50 | ns | load of 10 kΩ, 50 pF | 11 | ||
| Propagation delay (TOE to Q DISABLE) | tPTD | 130 | ns | load of 10 kΩ, 50 pF | 11 | ||
| Power-up time | tPU | 30 | ms | Note 3 | 11 | ||
| Power-down time | tPD | 20 | ms | 11 | |||
| Crystal/clock frequency | fC | 3.5759 | 3.5795 | 3.5831 | MHz | 11 | |
| Clock input rise time | tLHCL | 110 | ns | Ext. clock | 11 | ||
| Clock input fall time | tHLCL | 110 | ns | Ext. clock | 11 | ||
| Clock input duty cycle | DCCL | 40 | 50 | 60 | % | Ext. clock | 11 |
| Capacitive load (OSC2) | CLO | 15 | pF | 11 | |||
| Input impedance (IN+, IN-) | RIN | 10 | MΩ | @ 1 kHz | 8 | ||
| Input resistance (gain setting amplifier) | RIN | 10 | MΩ | 9 | |||
| Unity gain bandwidth | fC | 0.3 | MHz | 9 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | MT88L70ASR1 18 Pin SOIC* Tape & Reel * Pb Free Matte Tin | 1 |
CAD (KiCad official)
- Symbol:
MT88L70AS1 - Footprint:
Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm - 3D model: SOIC-18-300mil (KiCad packages3D, STEP)
- 3D model files:
mt88l70as1-etched.step/mt88l70as1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mt88l70as1.step/mt88l70as1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (16 pp, sha256
d0f63e39dba95a76, retrieved 2026-11-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).