component
MS8413
Public Made by Adomby adom
Hangzhou Ruimeng Tech Audio Interface ICs, SSOP-28. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Initial commit: component/ms8413
31c1212
MS8413
Hangzhou Ruimeng Tech · Audio Interface ICs · SSOP-28
MS8413 from Hangzhou Ruimeng Tech, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AUDIO/SFSEL1 | tri_state | Output during operation: low level indicates SPDIF signal is valid PCM; during reset used to set internal data format by pulling down to GND through 47K resistor. |
| 2 | 96KHz | output | Sample rate detection output: outputs "0" for sample rates ≤48kHz, outputs "1" for sample rates ≥88.1kHz; during reset external pull-up/down configures digital de-emphasis function. |
| 3 | SFSEL2 | input | Set internal data format by pulling up to VDD through 47K resistor. |
| 4 | FsSEL | input | Set internal MCLK frequency to 256Fs by pulling up to VDD through 47K resistor. |
| 5 | SFSEL0 | input | Set internal data format by pulling up to VDD through 47K resistor. |
| 6 | TX0 | output | Output during operation: fixed output of RXP0; during reset used to set internal PLL by pulling down to GND through 47K resistor. |
| 7 | VDD | power_in | Digital power supply. |
| 8 | MCLKOUT | output | S/PDIF PLL recovered master clock output port; must be connected to PIN10. |
| 9 | SDOUT | output | Serial audio data output monitoring port during operation; during reset must be pulled down to GND through 47K resistor. |
| 10 | MCLKIN | input | Internal DAC master clock input port; must be connected to PIN8. |
| 11 | QV | output | Internal static voltage filter interface output; external capacitor connection required. |
| 12 | AGND | power_in | Analog ground. |
| 13 | AOUTL | output | Analog output left channel port. |
| 14 | AFILT+ | output | Positive reference voltage for internal DAC; external capacitor connection required. |
| 15 | VAA | power_in | Analog power supply. |
| 16 | AOUTR | output | Analog output right channel port. |
| 17 | RXP3 | input | S/PDIF positive input 3 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 18 | RXP2 | input | S/PDIF positive input 2 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 19 | RXP1 | input | S/PDIF positive input 1 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 20 | RXP0 | input | S/PDIF positive input 0 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 21 | RXN | input | S/PDIF negative input for differential reception of S/PDIF encoded data; in single-ended signal mode must be AC coupled to ground through capacitor. |
| 22 | VPLL | power_in | Internal PLL power supply +3.3V; requires low noise power to ensure PLL stability. |
| 23 | GND | power_in | Internal PLL power ground. |
| 24 | PFILT | output | PLL loop filter output port; must be connected to RC network to PIN23. |
| 25 | RST | input | Reset input: when low MS8413 enters low power mode and all internal states reset; must remain low at power-up until supply voltage and all input clocks are stable in frequency and phase. |
| 26 | RXSEL1 | input | S/PDIF receiver multiplexer selection input to select one of RXP[3:0] as receiver input. |
| 27 | RXSEL0 | input | S/PDIF receiver multiplexer selection input to select one of RXP[3:0] as receiver input. |
| 28 | ERROR | output | Receiver error output: outputs "1" when received S/PDIF data is unstable or no S/PDIF signal input; must be pulled up to VDD through 47K resistor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Hangzhou Ruimeng Tech |
| Package | SSOP-28 |
| Category | Interface |
| Pins | 28 |
CAD (KiCad official)
- Symbol:
MS8413 - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files:
ms8413-etched.step/ms8413-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ms8413.step/ms8413.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Hangzhou Ruimeng Tech datasheet (21 pp, sha256
ca6454cd23f4ce33, retrieved 2026-09-21, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MS8413
**Hangzhou Ruimeng Tech** · Audio Interface ICs · SSOP-28
MS8413 from Hangzhou Ruimeng Tech, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AUDIO/SFSEL1 | tri_state | Output during operation: low level indicates SPDIF signal is valid PCM; during reset used to set internal data format by pulling down to GND through 47K resistor. |
| 2 | 96KHz | output | Sample rate detection output: outputs "0" for sample rates ≤48kHz, outputs "1" for sample rates ≥88.1kHz; during reset external pull-up/down configures digital de-emphasis function. |
| 3 | SFSEL2 | input | Set internal data format by pulling up to VDD through 47K resistor. |
| 4 | FsSEL | input | Set internal MCLK frequency to 256Fs by pulling up to VDD through 47K resistor. |
| 5 | SFSEL0 | input | Set internal data format by pulling up to VDD through 47K resistor. |
| 6 | TX0 | output | Output during operation: fixed output of RXP0; during reset used to set internal PLL by pulling down to GND through 47K resistor. |
| 7 | VDD | power_in | Digital power supply. |
| 8 | MCLKOUT | output | S/PDIF PLL recovered master clock output port; must be connected to PIN10. |
| 9 | SDOUT | output | Serial audio data output monitoring port during operation; during reset must be pulled down to GND through 47K resistor. |
| 10 | MCLKIN | input | Internal DAC master clock input port; must be connected to PIN8. |
| 11 | QV | output | Internal static voltage filter interface output; external capacitor connection required. |
| 12 | AGND | power_in | Analog ground. |
| 13 | AOUTL | output | Analog output left channel port. |
| 14 | AFILT+ | output | Positive reference voltage for internal DAC; external capacitor connection required. |
| 15 | VAA | power_in | Analog power supply. |
| 16 | AOUTR | output | Analog output right channel port. |
| 17 | RXP3 | input | S/PDIF positive input 3 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 18 | RXP2 | input | S/PDIF positive input 2 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 19 | RXP1 | input | S/PDIF positive input 1 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 20 | RXP0 | input | S/PDIF positive input 0 for single-ended or differential reception of S/PDIF encoded data; part of 4:1 input multiplexer selectable via RXSEL[1:0]. |
| 21 | RXN | input | S/PDIF negative input for differential reception of S/PDIF encoded data; in single-ended signal mode must be AC coupled to ground through capacitor. |
| 22 | VPLL | power_in | Internal PLL power supply +3.3V; requires low noise power to ensure PLL stability. |
| 23 | GND | power_in | Internal PLL power ground. |
| 24 | PFILT | output | PLL loop filter output port; must be connected to RC network to PIN23. |
| 25 | RST | input | Reset input: when low MS8413 enters low power mode and all internal states reset; must remain low at power-up until supply voltage and all input clocks are stable in frequency and phase. |
| 26 | RXSEL1 | input | S/PDIF receiver multiplexer selection input to select one of RXP[3:0] as receiver input. |
| 27 | RXSEL0 | input | S/PDIF receiver multiplexer selection input to select one of RXP[3:0] as receiver input. |
| 28 | ERROR | output | Receiver error output: outputs "1" when received S/PDIF data is unstable or no S/PDIF signal input; must be pulled up to VDD through 47K resistor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Hangzhou Ruimeng Tech |
| Package | SSOP-28 |
| Category | Interface |
| Pins | 28 |
## CAD (KiCad official)
- Symbol: `MS8413`
- Footprint: `Package_SO:SSOP-28_5.3x10.2mm_P0.65mm`
- 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files: `ms8413-etched.step` / `ms8413-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ms8413.step` / `ms8413.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Hangzhou Ruimeng Tech datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588904788709163008) (21 pp, sha256 `ca6454cd23f4ce33`, retrieved 2026-09-21, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ms8413-datasheet.pdf)