main
Ray Set visibility: public 2a97a84
{
  "schema_version": 1,
  "type": "component",
  "slug": "mpq4360gre-aec1-z",
  "title": "MPQ4360GRE-AEC1-Z",
  "brief": "Monolithic Power Systems DC-DC Converters, QFN-20(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.1.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "power management",
    "mpq4360gre-aec1-z",
    "factory-2.0.0",
    "extractor-text"
  ],
  "component": {
    "mpn": "MPQ4360GRE-AEC1-Z",
    "manufacturer": "Monolithic Power Systems",
    "package": "QFN-20(4x4)",
    "pin_count": 21,
    "category": "Power Management",
    "subcategory": "DC-DC Converters",
    "datasheet": "https://datasheet.lcsc.com/datasheet/pdf/f5a2535d3972dae236731468cacbc772.pdf",
    "parts": {
      "symbol": "mpq4360gre-aec1-z.kicad_sym",
      "footprint": "mpq4360gre-aec1-z.kicad_mod",
      "model_3d": "mpq4360gre-aec1-z-hero.glb",
      "model_3d_plain": "mpq4360gre-aec1-z-etched.glb",
      "model_3d_step": "mpq4360gre-aec1-z-etched.step",
      "model_3d_step_plain": "mpq4360gre-aec1-z.step",
      "lbr": "mpq4360gre-aec1-z.lbr"
    },
    "distributor_links": {
      "lcsc": "C5775979",
      "digikey": "1589-MPQ4360GRE-AEC1-ZTR-ND",
      "mouser": "946-MPQ4360GREAEC1Z"
    },
    "distributor_check": {
      "checked_at": "2026-10-28T16:43:19Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "1589-MPQ4360GRE-AEC1-ZTR-ND",
        "status": "found"
      },
      "mouser": {
        "pn": "946-MPQ4360GREAEC1Z",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "MODE",
        "type": "input",
        "description": "AAM or FCCM selection pin: pull high for forced continuous conduction mode and low for advanced asynchronous modulation under light loads, and do not float it."
      },
      {
        "number": "2",
        "name": "SYNCIN",
        "type": "input",
        "description": "SYNC input that accepts a 350kHz to 2.2MHz clock to synchronize the internal oscillator (except where VOUT is below 5V), must not be floated, and should have a 51k ohm or lower resistor to GND if the external clock cannot pull down strongly enough."
      },
      {
        "number": "3",
        "name": "VIN",
        "type": "power_in",
        "description": "Input supply for the internal control circuitry and the power switch connected to SW, operating from 3.3V to 40V with a decoupling capacitor placed close to the pin."
      },
      {
        "number": "4",
        "name": "PGND",
        "type": "power_in",
        "description": "Power ground for the power stage of the regulator."
      },
      {
        "number": "5",
        "name": "PGND",
        "type": "power_in",
        "description": "Power ground for the power stage of the regulator."
      },
      {
        "number": "6",
        "name": "BST",
        "type": "passive",
        "description": "Bootstrap pin that is the positive supply for the high-side MOSFET driver, requiring a bypass capacitor between BST and SW sized per the datasheet's External BST Diode and Resistor section."
      },
      {
        "number": "7",
        "name": "SW",
        "type": "output",
        "description": "Switch node that is the output of the internal power switch."
      },
      {
        "number": "8",
        "name": "SW",
        "type": "output",
        "description": "Switch node that is the output of the internal power switch."
      },
      {
        "number": "9",
        "name": "EN",
        "type": "input",
        "description": "Enable pin that shuts the chip down when pulled below 0.85V and enables it when pulled above 1V."
      },
      {
        "number": "10",
        "name": "PGND",
        "type": "power_in",
        "description": "Power ground for the power stage of the regulator."
      },
      {
        "number": "11",
        "name": "PGND",
        "type": "power_in",
        "description": "Power ground for the power stage of the regulator."
      },
      {
        "number": "12",
        "name": "VIN",
        "type": "power_in",
        "description": "Input supply for the internal control circuitry and the power switch connected to SW, operating from 3.3V to 40V with a decoupling capacitor placed close to the pin."
      },
      {
        "number": "13",
        "name": "SYNCO",
        "type": "output",
        "description": "SYNC output that provides a clock 180 degrees out of phase with the internal oscillator, and should be left floating if unused."
      },
      {
        "number": "14",
        "name": "PG",
        "type": "output",
        "description": "Open-drain power good output that goes high when VOUT is within 95% to 105% of nominal and low when VOUT is above 106.5% or below 93.5%, requiring a pull-up resistor if used."
      },
      {
        "number": "15",
        "name": "ICS",
        "type": "input",
        "description": "Current sharing pin that must not be floated, to be tied to VCC or to an output at least 3V in a single-phase application and connected in parallel across phases in multi-phase operation."
      },
      {
        "number": "16",
        "name": "VCC",
        "type": "power_out",
        "description": "Biased supply that provides 4.9V to the internal control circuit and gate drivers, requiring a decoupling capacitor placed close to the pin."
      },
      {
        "number": "17",
        "name": "AGND",
        "type": "power_in",
        "description": "Analog ground for the control circuitry."
      },
      {
        "number": "18",
        "name": "FB",
        "type": "input",
        "description": "Feedback input connected to the center of the output resistor divider to AGND, with a feedback threshold of 0.815V."
      },
      {
        "number": "19",
        "name": "SS",
        "type": "passive",
        "description": "Soft-start input with a capacitor from SS to GND that sets the soft-start period, as the device sources 6uA into this capacitor at start-up."
      },
      {
        "number": "20",
        "name": "FREQ",
        "type": "passive",
        "description": "Switching frequency configuration pin with a resistor from FREQ to ground that sets fSW per the fSW vs. RFREQ curves."
      },
      {
        "number": "21",
        "name": "EP",
        "type": "passive",
        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [],
        "pages_sent": 8,
        "cost_usd": 0.0192,
        "at": "2026-10-28T16:43:08"
      },
      "datasheet": {
        "url": "https://datasheet.lcsc.com/datasheet/pdf/f5a2535d3972dae236731468cacbc772.pdf",
        "pages": 44,
        "sha256": "79be3687a06236bb",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 21,
        "described": 21,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "mpq4360gre-aec1-z.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4,
          4,
          0.77
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "c9476a1612023de37f27b4972110ab6ac6dc0eaf5ac48957a2e1c497650082a5",
        "checked": "2026-10-28",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "mpq4360gre-aec1-z-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4,
          4,
          0.77
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "79163cb95c3d239a5758d761d70219ae6cb6f92534cc362ee2976e180259e36a",
        "checked": "2026-10-28",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  },
  "metadata": {
    "specs": {
      "Manufacturer": "Monolithic Power Systems",
      "Package": "QFN-20(4x4)",
      "Category": "Power Management",
      "Pins": "21"
    }
  },
  "variants": [],
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "mpq4360gre-aec1-z"
  ],
  "discovery_pitch": "MPQ4360GRE-AEC1-Z (Monolithic Power Systems) component page: datasheet pinout, KiCad symbol, footprint and 3D.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "mpq4360gre-aec1-z.kicad_sym",
    "mpq4360gre-aec1-z.kicad_mod",
    "mpq4360gre-aec1-z.glb",
    "mpq4360gre-aec1-z.step",
    "mpq4360gre-aec1-z.lbr",
    "docs/hero.png",
    "docs/mpq4360gre-aec1-z-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "mpq4360gre-aec1-z-hero.glb",
    "mpq4360gre-aec1-z-hero.overlay.json",
    "mpq4360gre-aec1-z-etched.glb"
  ],
  "visibility": {
    "public": true
  }
}