Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MPQ4360GRE-AEC1-Z

Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)

MPQ4360GRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MODE input AAM or FCCM selection pin: pull high for forced continuous conduction mode and low for advanced asynchronous modulation under light loads, and do not float it.
2 SYNCIN input SYNC input that accepts a 350kHz to 2.2MHz clock to synchronize the internal oscillator (except where VOUT is below 5V), must not be floated, and should have a 51k ohm or lower resistor to GND if the external clock cannot pull down strongly enough.
3 VIN power_in Input supply for the internal control circuitry and the power switch connected to SW, operating from 3.3V to 40V with a decoupling capacitor placed close to the pin.
4 PGND power_in Power ground for the power stage of the regulator.
5 PGND power_in Power ground for the power stage of the regulator.
6 BST passive Bootstrap pin that is the positive supply for the high-side MOSFET driver, requiring a bypass capacitor between BST and SW sized per the datasheet's External BST Diode and Resistor section.
7 SW output Switch node that is the output of the internal power switch.
8 SW output Switch node that is the output of the internal power switch.
9 EN input Enable pin that shuts the chip down when pulled below 0.85V and enables it when pulled above 1V.
10 PGND power_in Power ground for the power stage of the regulator.
11 PGND power_in Power ground for the power stage of the regulator.
12 VIN power_in Input supply for the internal control circuitry and the power switch connected to SW, operating from 3.3V to 40V with a decoupling capacitor placed close to the pin.
13 SYNCO output SYNC output that provides a clock 180 degrees out of phase with the internal oscillator, and should be left floating if unused.
14 PG output Open-drain power good output that goes high when VOUT is within 95% to 105% of nominal and low when VOUT is above 106.5% or below 93.5%, requiring a pull-up resistor if used.
15 ICS input Current sharing pin that must not be floated, to be tied to VCC or to an output at least 3V in a single-phase application and connected in parallel across phases in multi-phase operation.
16 VCC power_out Biased supply that provides 4.9V to the internal control circuit and gate drivers, requiring a decoupling capacitor placed close to the pin.
17 AGND power_in Analog ground for the control circuitry.
18 FB input Feedback input connected to the center of the output resistor divider to AGND, with a feedback threshold of 0.815V.
19 SS passive Soft-start input with a capacitor from SS to GND that sets the soft-start period, as the device sources 6uA into this capacitor at start-up.
20 FREQ passive Switching frequency configuration pin with a resistor from FREQ to ground that sets fSW per the fSW vs. RFREQ curves.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-20(4x4)
Category Power Management
Pins 21

CAD (KiCad official)

  • Symbol: MPQ4360GRE-AEC1-Z
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: mpq4360gre-aec1-z-etched.step / mpq4360gre-aec1-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mpq4360gre-aec1-z.step / mpq4360gre-aec1-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (44 pp, sha256 79be3687a06236bb, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF