Generated by kicad-footprint-generator · KiCad file format 20260206
MPQ4360GRE-AEC1-Z
Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)
MPQ4360GRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | AAM or FCCM selection pin: pull high for forced continuous conduction mode and low for advanced asynchronous modulation under light loads, and do not float it. |
| 2 | SYNCIN | input | SYNC input that accepts a 350kHz to 2.2MHz clock to synchronize the internal oscillator (except where VOUT is below 5V), must not be floated, and should have a 51k ohm or lower resistor to GND if the external clock cannot pull down strongly enough. |
| 3 | VIN | power_in | Input supply for the internal control circuitry and the power switch connected to SW, operating from 3.3V to 40V with a decoupling capacitor placed close to the pin. |
| 4 | PGND | power_in | Power ground for the power stage of the regulator. |
| 5 | PGND | power_in | Power ground for the power stage of the regulator. |
| 6 | BST | passive | Bootstrap pin that is the positive supply for the high-side MOSFET driver, requiring a bypass capacitor between BST and SW sized per the datasheet's External BST Diode and Resistor section. |
| 7 | SW | output | Switch node that is the output of the internal power switch. |
| 8 | SW | output | Switch node that is the output of the internal power switch. |
| 9 | EN | input | Enable pin that shuts the chip down when pulled below 0.85V and enables it when pulled above 1V. |
| 10 | PGND | power_in | Power ground for the power stage of the regulator. |
| 11 | PGND | power_in | Power ground for the power stage of the regulator. |
| 12 | VIN | power_in | Input supply for the internal control circuitry and the power switch connected to SW, operating from 3.3V to 40V with a decoupling capacitor placed close to the pin. |
| 13 | SYNCO | output | SYNC output that provides a clock 180 degrees out of phase with the internal oscillator, and should be left floating if unused. |
| 14 | PG | output | Open-drain power good output that goes high when VOUT is within 95% to 105% of nominal and low when VOUT is above 106.5% or below 93.5%, requiring a pull-up resistor if used. |
| 15 | ICS | input | Current sharing pin that must not be floated, to be tied to VCC or to an output at least 3V in a single-phase application and connected in parallel across phases in multi-phase operation. |
| 16 | VCC | power_out | Biased supply that provides 4.9V to the internal control circuit and gate drivers, requiring a decoupling capacitor placed close to the pin. |
| 17 | AGND | power_in | Analog ground for the control circuitry. |
| 18 | FB | input | Feedback input connected to the center of the output resistor divider to AGND, with a feedback threshold of 0.815V. |
| 19 | SS | passive | Soft-start input with a capacitor from SS to GND that sets the soft-start period, as the device sources 6uA into this capacitor at start-up. |
| 20 | FREQ | passive | Switching frequency configuration pin with a resistor from FREQ to ground that sets fSW per the fSW vs. RFREQ curves. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-20(4x4) |
| Category | Power Management |
| Pins | 21 |
CAD (KiCad official)
- Symbol:
MPQ4360GRE-AEC1-Z - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files:
mpq4360gre-aec1-z-etched.step/mpq4360gre-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq4360gre-aec1-z.step/mpq4360gre-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (44 pp, sha256
79be3687a06236bb, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).