main
History Download
Ray Publish 0.1.2 f425554

MP8008GV-Z

MONOLITHIC POWER SYSTEMS (MPS) · Global Sourcing Parts · QFN-28(4x5)

MP8008GV-Z from MONOLITHIC POWER SYSTEMS (MPS), in a QFN-28(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 AUX input Auxiliary power input detector; driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active.
2 DET passive Detection pin; a 24.9kΩ resistor must be connected between VDD and DET for PoE detection.
3 VDD power_in Positive power supply terminal from the PoE input power rail.
4 NC unconnected Not connected internally; connect NC to GND during layout.
5 PG output Power-good indicator pulled up by an internal current source when the PD output capacitor is fully charged; connect PG to EN/SYNC for flyback automatic start-up.
6 GATE output Gate driving signal that drives the external N-channel power MOSFET.
7 VCC power_out Output of the flyback controller internal 12V regulator, powered through an internal LDO from VIN; a capacitor must be connected between VCC and GND.
8 VIN power_in Flyback controller input supply; connect a bypass capacitor from VIN to GND.
9 GND power_in Power ground; the gate driver return pin.
10 RT passive Switching frequency set; a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz.
11 COMP passive Feedback for isolated flyback; COMP is the error amplifier output pin for non-isolated solutions.
12 FB input OVP monitor and feedback pin for non-isolated solutions; connect FB to GND if it is not used in isolated flyback.
13 EN/SYNC input On/off control input with an internal 1MΩ resistor to GND; an external clock higher than the RT-set frequency applied here synchronizes the switching frequency.
14 NC unconnected Not connected internally; connect NC to GND during layout.
15 NC unconnected Not connected internally; connect NC to GND during layout.
16 NC unconnected Not connected internally; connect NC to GND during layout.
17 NC unconnected Not connected internally; connect NC to GND during layout.
18 SS passive Soft start; one capacitor between SS and GND controls the COMP voltage rise and sets the hiccup protection delay.
19 ISENSE input Current sense and isolated/non-isolated mode setting; senses the sense-resistor voltage for current-mode control, cycle-by-cycle current limit, and overload and short-circuit protection.
20 RTN passive Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN.
21 RTN passive Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN.
22 NC unconnected Not connected internally; connect NC to GND during layout.
23 VSS power_in Negative power supply terminal from the PoE input power rail.
24 VSS power_in Negative power supply terminal from the PoE input power rail.
25 FTY passive Factory use only; FTY must be connected to VSS in application.
26 CLASS passive Classification; a resistor from CLASS to VSS programs the classification current.
27 T2P output Open-drain Type-2 PSE indicator; pulled low to VSS indicates a Type-2 PSE or a wall adapter.
28 NC unconnected Not connected internally; connect NC to GND during layout.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer MONOLITHIC POWER SYSTEMS (MPS)
Package QFN-28(4x5)
Category Global Sourcing Parts
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD, RTN, DET, T2P, AUX, GND voltage to VSS -0.3 100 V Pins referred to VSS 3
CLASS, FTY voltage to VSS -0.3 6.5 V Pins referred to VSS 3
VDD voltage to GND -0.3 100 V Referred to GND 3
VIN voltage to GND -0.3 40 V Referred to GND 3
VCC, GATE voltage to GND -0.3 15 V Referred to GND 3
All other pins voltage to GND -0.3 6 V Referred to GND 3
AUX voltage to VDD -6.5 0.3 V Pins voltage with respect to VDD 3
T2P sink current 10 mA 3
AUX sink current -5 mA Note 3: VDD clamps AUX; current limited by external resistor 3
PG sink current 1 mA Note 4: if PG pulled above 6.5V externally, pull-up current must be limited 3
EN/SYNC sink current 0.5 mA Note 5 3
Junction temperature TJ 150 °C 3
Storage temperature TSTORE -55 150 °C 3
Supply voltage VDD VDD 0 57 V Recommended operating conditions 3
VIN voltage VIN 7 35 V Recommended operating conditions 3
Maximum T2P sink current 5 mA 3
Maximum AUX sink current -3 mA Note 3 3
Maximum PG sink current 0.6 mA Note 4 3
Maximum EN/SYNC sink current 0.4 mA Note 5 3
Operating junction temperature TJ -40 125 °C 3
Junction-to-ambient thermal resistance θJA 40 °C/W QFN-28 (4mmx5mm); measured on JESD51-7, 2-layer PCB 3
Junction-to-case thermal resistance θJC 9 °C/W QFN-28 (4mmx5mm) 3
Detection current IDET 96 99 102 μA VDD = 2.5V, measure ISUPPLY 4
Detection current IDET 395 410 425 μA VDD = 10.1V, measure ISUPPLY 4
VCLASS output voltage VCLASS 1.1 1.16 1.21 V 13V < VDD < 21V, 1mA < ICLASS < 43mA 4
Classification current ICLASS 1.8 2 2.4 mA RCLASS = 578Ω, 13V ≤ VDD ≤ 21V 4
Classification current ICLASS 9.9 10.55 11.3 mA RCLASS = 110Ω, 13V ≤ VDD ≤ 21V 4
Classification current ICLASS 17.7 18.7 19.8 mA RCLASS = 62Ω, 13V ≤ VDD ≤ 21V 4
Classification current ICLASS 26.6 28.15 29.7 mA RCLASS = 41.2Ω, 13V ≤ VDD ≤ 21V 4
Classification current ICLASS 38.2 40.4 42.6 mA RCLASS = 28.7Ω, 13V ≤ VDD ≤ 21V 4
Classification lower threshold VCL-ON 11.8 12.5 13 V Class regulator turns on, VDD rising 4
Classification upper threshold VCL-OFF 21 22 23 V Class regulator turns off, VDD rising 4
Mark event reset threshold VMARK-L 4.5 5 5.5 V 4
Max mark event voltage VMARK-H 11 11.5 12 V 4
Mark event current IMARK 0.5 1.5 2 mA 4
VDD turn-on threshold VDD-VSS-R 35 37.5 40 V VDD rising 4
VDD turn-off threshold VDD-VSS-F 29 31 33 V VDD falling 4
Current limit ILIMIT 720 840 900 mA VRTN = 1V 5
Inrush to operation mode delay TDELAY 80 100 ms 5
VCC UVLO threshold VCC-UVLO 3.9 4.17 4.44 V Rising edge 6
VCC regulation voltage VCC 10.6 11.8 12.8 V Load = 0mA to 10mA 6
Limiting sense voltage VLIMIT 163 185 206 mV TJ = 25°C 6
Switching frequency FSW 308 337 363 kHz RT = 6.81kΩ 6
Switching frequency FSW 25 30 35 kHz RT = 80.6kΩ 6
FB reference voltage VFB 1.222 1.237 1.252 V TJ = 25°C 7
FB reference voltage VFB 1.211 1.237 1.258 V TJ = -40°C to 125°C 7
OVP reference level VOVP 1.391 1.438 1.479 V 7
Enable rising threshold VEN-RISING 1.463 1.628 1.793 V TJ = 25°C 7

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: MP8008GV-Z
  • Footprint: Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm
  • 3D model: QFN-28(4x5), generated on the KiCad land (body 4 x 5 mm, terminals on the pads, 0.9 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: mp8008gv-z-etched.step / mp8008gv-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp8008gv-z.step / mp8008gv-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: MONOLITHIC POWER SYSTEMS (MPS) datasheet, copy hosted by LCSC (28 pp, sha256 620be15933636006, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF