Generated by kicad-footprint-generator · KiCad file format 20260206
MP8008GV-Z
MONOLITHIC POWER SYSTEMS (MPS) · Global Sourcing Parts · QFN-28(4x5)
MP8008GV-Z from MONOLITHIC POWER SYSTEMS (MPS), in a QFN-28(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AUX | input | Auxiliary power input detector; driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active. |
| 2 | DET | passive | Detection pin; a 24.9kΩ resistor must be connected between VDD and DET for PoE detection. |
| 3 | VDD | power_in | Positive power supply terminal from the PoE input power rail. |
| 4 | NC | unconnected | Not connected internally; connect NC to GND during layout. |
| 5 | PG | output | Power-good indicator pulled up by an internal current source when the PD output capacitor is fully charged; connect PG to EN/SYNC for flyback automatic start-up. |
| 6 | GATE | output | Gate driving signal that drives the external N-channel power MOSFET. |
| 7 | VCC | power_out | Output of the flyback controller internal 12V regulator, powered through an internal LDO from VIN; a capacitor must be connected between VCC and GND. |
| 8 | VIN | power_in | Flyback controller input supply; connect a bypass capacitor from VIN to GND. |
| 9 | GND | power_in | Power ground; the gate driver return pin. |
| 10 | RT | passive | Switching frequency set; a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz. |
| 11 | COMP | passive | Feedback for isolated flyback; COMP is the error amplifier output pin for non-isolated solutions. |
| 12 | FB | input | OVP monitor and feedback pin for non-isolated solutions; connect FB to GND if it is not used in isolated flyback. |
| 13 | EN/SYNC | input | On/off control input with an internal 1MΩ resistor to GND; an external clock higher than the RT-set frequency applied here synchronizes the switching frequency. |
| 14 | NC | unconnected | Not connected internally; connect NC to GND during layout. |
| 15 | NC | unconnected | Not connected internally; connect NC to GND during layout. |
| 16 | NC | unconnected | Not connected internally; connect NC to GND during layout. |
| 17 | NC | unconnected | Not connected internally; connect NC to GND during layout. |
| 18 | SS | passive | Soft start; one capacitor between SS and GND controls the COMP voltage rise and sets the hiccup protection delay. |
| 19 | ISENSE | input | Current sense and isolated/non-isolated mode setting; senses the sense-resistor voltage for current-mode control, cycle-by-cycle current limit, and overload and short-circuit protection. |
| 20 | RTN | passive | Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN. |
| 21 | RTN | passive | Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN. |
| 22 | NC | unconnected | Not connected internally; connect NC to GND during layout. |
| 23 | VSS | power_in | Negative power supply terminal from the PoE input power rail. |
| 24 | VSS | power_in | Negative power supply terminal from the PoE input power rail. |
| 25 | FTY | passive | Factory use only; FTY must be connected to VSS in application. |
| 26 | CLASS | passive | Classification; a resistor from CLASS to VSS programs the classification current. |
| 27 | T2P | output | Open-drain Type-2 PSE indicator; pulled low to VSS indicates a Type-2 PSE or a wall adapter. |
| 28 | NC | unconnected | Not connected internally; connect NC to GND during layout. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MONOLITHIC POWER SYSTEMS (MPS) |
| Package | QFN-28(4x5) |
| Category | Global Sourcing Parts |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD, RTN, DET, T2P, AUX, GND voltage to VSS | -0.3 | 100 | V | Pins referred to VSS | 3 | ||
| CLASS, FTY voltage to VSS | -0.3 | 6.5 | V | Pins referred to VSS | 3 | ||
| VDD voltage to GND | -0.3 | 100 | V | Referred to GND | 3 | ||
| VIN voltage to GND | -0.3 | 40 | V | Referred to GND | 3 | ||
| VCC, GATE voltage to GND | -0.3 | 15 | V | Referred to GND | 3 | ||
| All other pins voltage to GND | -0.3 | 6 | V | Referred to GND | 3 | ||
| AUX voltage to VDD | -6.5 | 0.3 | V | Pins voltage with respect to VDD | 3 | ||
| T2P sink current | 10 | mA | 3 | ||||
| AUX sink current | -5 | mA | Note 3: VDD clamps AUX; current limited by external resistor | 3 | |||
| PG sink current | 1 | mA | Note 4: if PG pulled above 6.5V externally, pull-up current must be limited | 3 | |||
| EN/SYNC sink current | 0.5 | mA | Note 5 | 3 | |||
| Junction temperature | TJ | 150 | °C | 3 | |||
| Storage temperature | TSTORE | -55 | 150 | °C | 3 | ||
| Supply voltage VDD | VDD | 0 | 57 | V | Recommended operating conditions | 3 | |
| VIN voltage | VIN | 7 | 35 | V | Recommended operating conditions | 3 | |
| Maximum T2P sink current | 5 | mA | 3 | ||||
| Maximum AUX sink current | -3 | mA | Note 3 | 3 | |||
| Maximum PG sink current | 0.6 | mA | Note 4 | 3 | |||
| Maximum EN/SYNC sink current | 0.4 | mA | Note 5 | 3 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| Junction-to-ambient thermal resistance | θJA | 40 | °C/W | QFN-28 (4mmx5mm); measured on JESD51-7, 2-layer PCB | 3 | ||
| Junction-to-case thermal resistance | θJC | 9 | °C/W | QFN-28 (4mmx5mm) | 3 | ||
| Detection current | IDET | 96 | 99 | 102 | μA | VDD = 2.5V, measure ISUPPLY | 4 |
| Detection current | IDET | 395 | 410 | 425 | μA | VDD = 10.1V, measure ISUPPLY | 4 |
| VCLASS output voltage | VCLASS | 1.1 | 1.16 | 1.21 | V | 13V < VDD < 21V, 1mA < ICLASS < 43mA | 4 |
| Classification current | ICLASS | 1.8 | 2 | 2.4 | mA | RCLASS = 578Ω, 13V ≤ VDD ≤ 21V | 4 |
| Classification current | ICLASS | 9.9 | 10.55 | 11.3 | mA | RCLASS = 110Ω, 13V ≤ VDD ≤ 21V | 4 |
| Classification current | ICLASS | 17.7 | 18.7 | 19.8 | mA | RCLASS = 62Ω, 13V ≤ VDD ≤ 21V | 4 |
| Classification current | ICLASS | 26.6 | 28.15 | 29.7 | mA | RCLASS = 41.2Ω, 13V ≤ VDD ≤ 21V | 4 |
| Classification current | ICLASS | 38.2 | 40.4 | 42.6 | mA | RCLASS = 28.7Ω, 13V ≤ VDD ≤ 21V | 4 |
| Classification lower threshold | VCL-ON | 11.8 | 12.5 | 13 | V | Class regulator turns on, VDD rising | 4 |
| Classification upper threshold | VCL-OFF | 21 | 22 | 23 | V | Class regulator turns off, VDD rising | 4 |
| Mark event reset threshold | VMARK-L | 4.5 | 5 | 5.5 | V | 4 | |
| Max mark event voltage | VMARK-H | 11 | 11.5 | 12 | V | 4 | |
| Mark event current | IMARK | 0.5 | 1.5 | 2 | mA | 4 | |
| VDD turn-on threshold | VDD-VSS-R | 35 | 37.5 | 40 | V | VDD rising | 4 |
| VDD turn-off threshold | VDD-VSS-F | 29 | 31 | 33 | V | VDD falling | 4 |
| Current limit | ILIMIT | 720 | 840 | 900 | mA | VRTN = 1V | 5 |
| Inrush to operation mode delay | TDELAY | 80 | 100 | ms | 5 | ||
| VCC UVLO threshold | VCC-UVLO | 3.9 | 4.17 | 4.44 | V | Rising edge | 6 |
| VCC regulation voltage | VCC | 10.6 | 11.8 | 12.8 | V | Load = 0mA to 10mA | 6 |
| Limiting sense voltage | VLIMIT | 163 | 185 | 206 | mV | TJ = 25°C | 6 |
| Switching frequency | FSW | 308 | 337 | 363 | kHz | RT = 6.81kΩ | 6 |
| Switching frequency | FSW | 25 | 30 | 35 | kHz | RT = 80.6kΩ | 6 |
| FB reference voltage | VFB | 1.222 | 1.237 | 1.252 | V | TJ = 25°C | 7 |
| FB reference voltage | VFB | 1.211 | 1.237 | 1.258 | V | TJ = -40°C to 125°C | 7 |
| OVP reference level | VOVP | 1.391 | 1.438 | 1.479 | V | 7 | |
| Enable rising threshold | VEN-RISING | 1.463 | 1.628 | 1.793 | V | TJ = 25°C | 7 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
MP8008GV-Z - Footprint:
Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-28(4x5), generated on the KiCad land (body 4 x 5 mm, terminals on the pads, 0.9 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
mp8008gv-z-etched.step/mp8008gv-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp8008gv-z.step/mp8008gv-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MONOLITHIC POWER SYSTEMS (MPS) datasheet, copy hosted by LCSC (28 pp, sha256
620be15933636006, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).