← Commit history
README.md+61−70
@@ -8,34 +8,34 @@ MP8008GV-Z from MONOLITHIC POWER SYSTEMS (MPS), in a QFN-28(4x5). Pinout and pin  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | AUX | input | Auxiliary power input detector: driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active. |-| 2 | DET | passive | Detection pin: connect a 24.9kΩ (±1%) resistor between VDD and DET for the PoE detection signature, with a valid signature resistance of 23.7kΩ to 26.3kΩ. |-| 3 | VDD | power_in | Positive power supply terminal from the PoE input power rail, with a recommended supply voltage of 0V to 57V and an absolute maximum of -0.3V to +100V. |-| 4 | NC | unconnected | Not connected internally; connect to GND during layout. |-| 5 | PG | output | PD supply power good indicator, pulled up by an internal current source when the PD output capacitor is fully charged; connect to EN/SYNC for flyback automatic start-up, with a recommended PG sink current of no more than 0.6mA. |-| 6 | GATE | output | Gate driving signal that drives the external N-channel power MOSFET, with a sourcing impedance of 4.1Ω and a sinking impedance of 2Ω. |-| 7 | VCC | power_out | Flyback controller internal 12V regulator output, supplied through an internal LDO from VIN, which must be bypassed with a capacitor of no less than 1µF. |-| 8 | VIN | power_in | Flyback controller input supply, operating from 7V to 35V, with a bypass capacitor connected from VIN to GND. |-| 9 | GND | power_in | Power ground and gate driver return; GND must be connected to RTN and the exposed pad must be connected to GND. |-| 10 | RT | passive | Switching frequency set: a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz. |-| 11 | COMP | bidirectional | Feedback input for isolated flyback and error amplifier output for non-isolated solutions, which requires an R-C compensation network in non-isolated mode. |-| 12 | FB | input | Feedback and OVP monitor for non-isolated flyback, with an OVP reference of 1.438V typical; connect to GND if not used in isolated flyback. |-| 13 | EN/SYNC | input | On/off control input with an internal 1MΩ pull-down to GND and an enable rising threshold of 1.628V typical, which can also accept an external clock above the RT-set frequency for synchronization; external pull-up current must be limited to 0.4mA. |-| 14 | NC | unconnected | Not connected internally; connect to GND during layout. |-| 15 | NC | unconnected | Not connected internally; connect to GND during layout. |-| 16 | NC | unconnected | Not connected internally; connect to GND during layout. |-| 17 | NC | unconnected | Not connected internally; connect to GND during layout. |-| 18 | SS | passive | Soft-start pin: a capacitor from SS to GND sets the soft-start time and hiccup protection delay, with the SS voltage clamped at 3.65V during normal operation. |-| 19 | ISENSE | input | Current sense and feedback mode setting pin that senses the sense resistor voltage for cycle-by-cycle current limit, with an ISENSE current limit threshold of 185mV typical. |-| 20 | RTN | passive | Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN, with an RTN on-resistance of 0.48Ω typical at 600mA. |-| 21 | RTN | passive | Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN, with an RTN on-resistance of 0.48Ω typical at 600mA. |-| 22 | NC | unconnected | Not connected internally; connect to GND during layout. |-| 23 | VSS | power_in | Negative power supply terminal from the PoE input power rail, which serves as the reference for VDD, DET, CLASS, T2P and RTN voltages. |-| 24 | VSS | power_in | Negative power supply terminal from the PoE input power rail, which serves as the reference for VDD, DET, CLASS, T2P and RTN voltages. |+| 1 | AUX | input | Auxiliary power input detector; driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active. |+| 2 | DET | passive | Detection pin; a 24.9kΩ resistor must be connected between VDD and DET for PoE detection. |+| 3 | VDD | power_in | Positive power supply terminal from the PoE input power rail. |+| 4 | NC | unconnected | Not connected internally; connect NC to GND during layout. |+| 5 | PG | output | Power-good indicator pulled up by an internal current source when the PD output capacitor is fully charged; connect PG to EN/SYNC for flyback automatic start-up. |+| 6 | GATE | output | Gate driving signal that drives the external N-channel power MOSFET. |+| 7 | VCC | power_out | Output of the flyback controller internal 12V regulator, powered through an internal LDO from VIN; a capacitor must be connected between VCC and GND. |+| 8 | VIN | power_in | Flyback controller input supply; connect a bypass capacitor from VIN to GND. |+| 9 | GND | power_in | Power ground; the gate driver return pin. |+| 10 | RT | passive | Switching frequency set; a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz. |+| 11 | COMP | passive | Feedback for isolated flyback; COMP is the error amplifier output pin for non-isolated solutions. |+| 12 | FB | input | OVP monitor and feedback pin for non-isolated solutions; connect FB to GND if it is not used in isolated flyback. |+| 13 | EN/SYNC | input | On/off control input with an internal 1MΩ resistor to GND; an external clock higher than the RT-set frequency applied here synchronizes the switching frequency. |+| 14 | NC | unconnected | Not connected internally; connect NC to GND during layout. |+| 15 | NC | unconnected | Not connected internally; connect NC to GND during layout. |+| 16 | NC | unconnected | Not connected internally; connect NC to GND during layout. |+| 17 | NC | unconnected | Not connected internally; connect NC to GND during layout. |+| 18 | SS | passive | Soft start; one capacitor between SS and GND controls the COMP voltage rise and sets the hiccup protection delay. |+| 19 | ISENSE | input | Current sense and isolated/non-isolated mode setting; senses the sense-resistor voltage for current-mode control, cycle-by-cycle current limit, and overload and short-circuit protection. |+| 20 | RTN | passive | Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN. |+| 21 | RTN | passive | Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN. |+| 22 | NC | unconnected | Not connected internally; connect NC to GND during layout. |+| 23 | VSS | power_in | Negative power supply terminal from the PoE input power rail. |+| 24 | VSS | power_in | Negative power supply terminal from the PoE input power rail. | | 25 | FTY | passive | Factory use only; FTY must be connected to VSS in application. |-| 26 | CLASS | passive | Classification pin: connect a resistor from CLASS to VSS to program the classification current, with a typical CLASS voltage of 1.16V in the classification range. |-| 27 | T2P | output | Type-2 PSE indicator, an active-low open-drain output that indicates a Type-2 PSE or wall adapter presence, with a maximum sink current of 5mA referenced to VSS. |-| 28 | NC | unconnected | Not connected internally; connect to GND during layout. |+| 26 | CLASS | passive | Classification; a resistor from CLASS to VSS programs the classification current. |+| 27 | T2P | output | Open-drain Type-2 PSE indicator; pulled low to VSS indicates a Type-2 PSE or a wall adapter. |+| 28 | NC | unconnected | Not connected internally; connect NC to GND during layout. | | 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |  ## Key specifications@@ -53,63 +53,54 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| Voltage on VDD, RTN, DET, T2P, AUX, GND (to VSS) |  | -0.3 |  | 100 | V | Pins voltages with respect to VSS | 3 |-| Voltage on CLASS, FTY (to VSS) |  | -0.3 |  | 6.5 | V | Pins voltages with respect to VSS | 3 |-| Voltage on VDD (to GND) |  | -0.3 |  | 100 | V | Pins voltages with respect to GND | 3 |-| Voltage on VIN (to GND) |  | -0.3 |  | 40 | V | Pins voltages with respect to GND | 3 |-| Voltage on VCC, GATE (to GND) |  | -0.3 |  | 15 | V | Pins voltages with respect to GND | 3 |-| Voltage on all other pins (to GND) |  | -0.3 |  | 6 | V | Pins voltages with respect to GND | 3 |-| Voltage on AUX (to VDD) |  | -6.5 |  | 0.3 | V | Pins voltage with respect to VDD | 3 |+| VDD, RTN, DET, T2P, AUX, GND voltage to VSS |  | -0.3 |  | 100 | V | Pins referred to VSS | 3 |+| CLASS, FTY voltage to VSS |  | -0.3 |  | 6.5 | V | Pins referred to VSS | 3 |+| VDD voltage to GND |  | -0.3 |  | 100 | V | Referred to GND | 3 |+| VIN voltage to GND |  | -0.3 |  | 40 | V | Referred to GND | 3 |+| VCC, GATE voltage to GND |  | -0.3 |  | 15 | V | Referred to GND | 3 |+| All other pins voltage to GND |  | -0.3 |  | 6 | V | Referred to GND | 3 |+| AUX voltage to VDD |  | -6.5 |  | 0.3 | V | Pins voltage with respect to VDD | 3 | | T2P sink current |  |  |  | 10 | mA |  | 3 |-| AUX sink current |  | -5 |  |  | mA | See note 3 | 3 |-| PG sink current |  |  |  | 1 | mA | See note 4 | 3 |-| EN/SYNC sink current |  |  |  | 0.5 | mA | See note 5 | 3 |-| Junction temperature |  |  |  | 150 | °C |  | 3 |-| Storage temperature |  | -55 |  | 150 | °C |  | 3 |-| Supply voltage (VDD) | VDD | 0 |  | 57 | V |  | 3 |-| VIN voltage | VIN | 7 |  | 35 | V |  | 3 |+| AUX sink current |  | -5 |  |  | mA | Note 3: VDD clamps AUX; current limited by external resistor | 3 |+| PG sink current |  |  |  | 1 | mA | Note 4: if PG pulled above 6.5V externally, pull-up current must be limited | 3 |+| EN/SYNC sink current |  |  |  | 0.5 | mA | Note 5 | 3 |+| Junction temperature | TJ |  |  | 150 | °C |  | 3 |+| Storage temperature | TSTORE | -55 |  | 150 | °C |  | 3 |+| Supply voltage VDD | VDD | 0 |  | 57 | V | Recommended operating conditions | 3 |+| VIN voltage | VIN | 7 |  | 35 | V | Recommended operating conditions | 3 | | Maximum T2P sink current |  |  |  | 5 | mA |  | 3 |-| Maximum AUX sink current |  |  |  | -3 | mA | See note 3 | 3 |-| Maximum PG sink current |  |  |  | 0.6 | mA | See note 4 | 3 |-| Maximum EN/SYNC sink current |  |  |  | 0.4 | mA | See note 5 | 3 |-| Operating junction temp. (TJ) | TJ | -40 |  | 125 | °C |  | 3 |-| DET leakage current | VDET-LK |  | 0.1 | 5 | μA | VDET = VDD = 57V, measure IDET | 4 |-| Detection current (VDD = 2.5V) | IDET | 96 | 99 | 102 | μA | VDD = 2.5V, measure ISUPPLY | 4 |-| Detection current (VDD = 10.1V) | IDET | 395 | 410 | 425 | μA | VDD = 10.1V, measure ISUPPLY | 4 |+| Maximum AUX sink current |  | -3 |  |  | mA | Note 3 | 3 |+| Maximum PG sink current |  |  |  | 0.6 | mA | Note 4 | 3 |+| Maximum EN/SYNC sink current |  |  |  | 0.4 | mA | Note 5 | 3 |+| Operating junction temperature | TJ | -40 |  | 125 | °C |  | 3 |+| Junction-to-ambient thermal resistance | θJA |  | 40 |  | °C/W | QFN-28 (4mmx5mm); measured on JESD51-7, 2-layer PCB | 3 |+| Junction-to-case thermal resistance | θJC |  | 9 |  | °C/W | QFN-28 (4mmx5mm) | 3 |+| Detection current | IDET | 96 | 99 | 102 | μA | VDD = 2.5V, measure ISUPPLY | 4 |+| Detection current | IDET | 395 | 410 | 425 | μA | VDD = 10.1V, measure ISUPPLY | 4 | | VCLASS output voltage | VCLASS | 1.1 | 1.16 | 1.21 | V | 13V < VDD < 21V, 1mA < ICLASS < 43mA | 4 |-| Classification current, RCLASS = 578Ω | ICLASS | 1.8 | 2 | 2.4 | mA | RCLASS = 578Ω, 13V ≤ VDD ≤ 21V | 4 |-| Classification current, RCLASS = 110Ω | ICLASS | 9.9 | 10.55 | 11.3 | mA | RCLASS = 110Ω, 13V ≤ VDD ≤ 21V | 4 |-| Classification current, RCLASS = 62Ω | ICLASS | 17.7 | 18.7 | 19.8 | mA | RCLASS = 62Ω, 13V ≤ VDD ≤ 21V | 4 |-| Classification current, RCLASS = 41.2Ω | ICLASS | 26.6 | 28.15 | 29.7 | mA | RCLASS = 41.2Ω, 13V ≤ VDD ≤ 21V | 4 |-| Classification current, RCLASS = 28.7Ω | ICLASS | 38.2 | 40.4 | 42.6 | mA | RCLASS = 28.7Ω, 13V ≤ VDD ≤ 21V | 4 |+| Classification current | ICLASS | 1.8 | 2 | 2.4 | mA | RCLASS = 578Ω, 13V ≤ VDD ≤ 21V | 4 |+| Classification current | ICLASS | 9.9 | 10.55 | 11.3 | mA | RCLASS = 110Ω, 13V ≤ VDD ≤ 21V | 4 |+| Classification current | ICLASS | 17.7 | 18.7 | 19.8 | mA | RCLASS = 62Ω, 13V ≤ VDD ≤ 21V | 4 |+| Classification current | ICLASS | 26.6 | 28.15 | 29.7 | mA | RCLASS = 41.2Ω, 13V ≤ VDD ≤ 21V | 4 |+| Classification current | ICLASS | 38.2 | 40.4 | 42.6 | mA | RCLASS = 28.7Ω, 13V ≤ VDD ≤ 21V | 4 | | Classification lower threshold | VCL-ON | 11.8 | 12.5 | 13 | V | Class regulator turns on, VDD rising | 4 | | Classification upper threshold | VCL-OFF | 21 | 22 | 23 | V | Class regulator turns off, VDD rising | 4 | | Mark event reset threshold | VMARK-L | 4.5 | 5 | 5.5 | V |  | 4 | | Max mark event voltage | VMARK-H | 11 | 11.5 | 12 | V |  | 4 | | Mark event current | IMARK | 0.5 | 1.5 | 2 | mA |  | 4 |-| IC supply current during classification | IIN-CLASS |  | 220 | 300 | μA | VDD = 17.5V, CLASS floating | 4 | | VDD turn-on threshold | VDD-VSS-R | 35 | 37.5 | 40 | V | VDD rising | 4 | | VDD turn-off threshold | VDD-VSS-F | 29 | 31 | 33 | V | VDD falling | 4 |-| Leakage current (pass device) | IRTN-LK |  | 1 | 15 | μA | VDD = VRTN = 57V | 5 | | Current limit | ILIMIT | 720 | 840 | 900 | mA | VRTN = 1V | 5 |-| Inrush to operation mode delay | TDELAY |  | 80 | 100 | ms |  | 5 |-| T2P output low voltage |  |  | 0.1 | 0.3 | V | IT2P = 2mA, respect to VSS | 5 |+| Inrush to operation mode delay | TDELAY | 80 | 100 |  | ms |  | 5 | | VCC UVLO threshold | VCC-UVLO | 3.9 | 4.17 | 4.44 | V | Rising edge | 6 | | VCC regulation voltage | VCC | 10.6 | 11.8 | 12.8 | V | Load = 0mA to 10mA | 6 |-| Quiescent current | IQ |  | 0.4 | 0.6 | mA | VFB = 1.35V, test supply from VIN to GND | 6 |-| ISENSE limit | VLIMIT | 163 | 185 | 206 | mV | TJ = 25°C | 6 |-| Minimum on time | TON |  | 214 | 400 | ns |  | 6 |-| Maximum duty cycle | DMAX |  | 93 | 95 | % | RT = 6.81kΩ | 6 |-| Switching frequency (RT = 6.81kΩ) | FSW | 308 | 337 | 363 | kHz | RT = 6.81kΩ | 6 |-| Switching frequency (RT = 80.6kΩ) | FSW | 25 | 30 | 35 | kHz | RT = 80.6kΩ | 6 |-| FB reference voltage (TJ = 25°C) | VFB | 1.222 | 1.237 | 1.252 | V | TJ = 25°C | 7 |-| FB reference voltage (TJ = -40°C to 125°C) | VFB | 1.211 | 1.237 | 1.258 | V | TJ = -40°C to 125°C | 7 |-| FB bias current | IFB |  | 0.01 | 0.15 | μA | VFB = 1.237V, TJ = 25°C | 7 |+| Limiting sense voltage | VLIMIT | 163 | 185 | 206 | mV | TJ = 25°C | 6 |+| Switching frequency | FSW | 308 | 337 | 363 | kHz | RT = 6.81kΩ | 6 |+| Switching frequency | FSW | 25 | 30 | 35 | kHz | RT = 80.6kΩ | 6 |+| FB reference voltage | VFB | 1.222 | 1.237 | 1.252 | V | TJ = 25°C | 7 |+| FB reference voltage | VFB | 1.211 | 1.237 | 1.258 | V | TJ = -40°C to 125°C | 7 | | OVP reference level | VOVP | 1.391 | 1.438 | 1.479 | V |  | 7 | | Enable rising threshold | VEN-RISING | 1.463 | 1.628 | 1.793 | V | TJ = 25°C | 7 |-| Enable input current | IEN |  | 2.5 | 5 | μA | VEN = 3V | 7 |-| Thermal resistance, junction-to-ambient (QFN-28 4mmx5mm) | θJA |  | 40 |  | °C/W | Measured on JESD51-7, 2-layer PCB | 3 |-| Thermal resistance, junction-to-case (QFN-28 4mmx5mm) | θJC |  | 9 |  | °C/W |  | 3 |  ## CAD (land: KiCad; 3D: generated from the datasheet) @@ -122,7 +113,7 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [MONOLITHIC POWER SYSTEMS (MPS) datasheet](docs/mp8008gv-z-datasheet.pdf) (28 pp, sha256 `620be15933636006`, retrieved 2026-11-13, tier: lcsc)+- **Datasheet:** [MONOLITHIC POWER SYSTEMS (MPS) datasheet, copy hosted by LCSC](docs/mp8008gv-z-datasheet.pdf) (28 pp, sha256 `620be15933636006`, retrieved 2026-11-20) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated). 
mp8008gv-z.kicad_sym+1−1
@@ -48,7 +48,7 @@       (name "RT" (effects (font (size 1.27 1.27))))       (number "10" (effects (font (size 1.27 1.27))))     )-    (pin bidirectional line (at -17.78 -7.62 0) (length 5.08)+    (pin passive line (at -17.78 -7.62 0) (length 5.08)       (name "COMP" (effects (font (size 1.27 1.27))))       (number "11" (effects (font (size 1.27 1.27))))     )
mp8008gv-z.lbr+1−1
@@ -126,7 +126,7 @@   <pin name="VIN" x="-17.78" y="0" length="middle" direction="pwr"/>   <pin name="GND" x="-17.78" y="-2.54" length="middle" direction="pwr"/>   <pin name="RT" x="-17.78" y="-5.08" length="middle" direction="pas"/>-  <pin name="COMP" x="-17.78" y="-7.62" length="middle" direction="io"/>+  <pin name="COMP" x="-17.78" y="-7.62" length="middle" direction="pas"/>   <pin name="FB" x="-17.78" y="-10.16" length="middle" direction="in"/>   <pin name="EN/SYNC" x="-17.78" y="-12.7" length="middle" direction="in"/>   <pin name="NC@2" x="-17.78" y="-15.24" length="middle" direction="nc"/>
mp8008gv-z.step+1−1
@@ -1,7 +1,7 @@ ISO-10303-21; HEADER; FILE_DESCRIPTION(('Open CASCADE Model'),'2;1');-FILE_NAME('Open CASCADE Shape Model','2026-11-13T03:20:16',('Author'),(+FILE_NAME('Open CASCADE Shape Model','2026-11-20T07:53:30',('Author'),(     'Open CASCADE'),'Open CASCADE STEP processor 7.9','Open CASCADE 7.9'   ,'Unknown'); FILE_SCHEMA(('AUTOMOTIVE_DESIGN { 1 0 10303 214 1 1 1 1 }'));
package.json+731−38
@@ -1,6 +1,6 @@ {   "slug": "mp8008gv-z",-  "version": "0.1.1",+  "version": "0.1.2",   "type": "component",   "description": "MONOLITHIC POWER SYSTEMS (MPS) Global Sourcing Parts, QFN-28(4x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -53,7 +53,7 @@       "mouser": "946-MP8008GV-Z"     },     "distributor_check": {-      "checked_at": "2026-11-13T03:20:24Z",+      "checked_at": "2026-11-20T07:53:39Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "1589-1728-2-ND",@@ -69,145 +69,145 @@         "number": "1",         "name": "AUX",         "type": "input",-        "description": "Auxiliary power input detector: driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active."+        "description": "Auxiliary power input detector; driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active."       },       {         "number": "2",         "name": "DET",         "type": "passive",-        "description": "Detection pin: connect a 24.9kΩ (±1%) resistor between VDD and DET for the PoE detection signature, with a valid signature resistance of 23.7kΩ to 26.3kΩ."+        "description": "Detection pin; a 24.9kΩ resistor must be connected between VDD and DET for PoE detection."       },       {         "number": "3",         "name": "VDD",         "type": "power_in",-        "description": "Positive power supply terminal from the PoE input power rail, with a recommended supply voltage of 0V to 57V and an absolute maximum of -0.3V to +100V."+        "description": "Positive power supply terminal from the PoE input power rail."       },       {         "number": "4",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "5",         "name": "PG",         "type": "output",-        "description": "PD supply power good indicator, pulled up by an internal current source when the PD output capacitor is fully charged; connect to EN/SYNC for flyback automatic start-up, with a recommended PG sink current of no more than 0.6mA."+        "description": "Power-good indicator pulled up by an internal current source when the PD output capacitor is fully charged; connect PG to EN/SYNC for flyback automatic start-up."       },       {         "number": "6",         "name": "GATE",         "type": "output",-        "description": "Gate driving signal that drives the external N-channel power MOSFET, with a sourcing impedance of 4.1Ω and a sinking impedance of 2Ω."+        "description": "Gate driving signal that drives the external N-channel power MOSFET."       },       {         "number": "7",         "name": "VCC",         "type": "power_out",-        "description": "Flyback controller internal 12V regulator output, supplied through an internal LDO from VIN, which must be bypassed with a capacitor of no less than 1µF."+        "description": "Output of the flyback controller internal 12V regulator, powered through an internal LDO from VIN; a capacitor must be connected between VCC and GND."       },       {         "number": "8",         "name": "VIN",         "type": "power_in",-        "description": "Flyback controller input supply, operating from 7V to 35V, with a bypass capacitor connected from VIN to GND."+        "description": "Flyback controller input supply; connect a bypass capacitor from VIN to GND."       },       {         "number": "9",         "name": "GND",         "type": "power_in",-        "description": "Power ground and gate driver return; GND must be connected to RTN and the exposed pad must be connected to GND."+        "description": "Power ground; the gate driver return pin."       },       {         "number": "10",         "name": "RT",         "type": "passive",-        "description": "Switching frequency set: a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz."+        "description": "Switching frequency set; a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz."       },       {         "number": "11",         "name": "COMP",-        "type": "bidirectional",-        "description": "Feedback input for isolated flyback and error amplifier output for non-isolated solutions, which requires an R-C compensation network in non-isolated mode."+        "type": "passive",+        "description": "Feedback for isolated flyback; COMP is the error amplifier output pin for non-isolated solutions."       },       {         "number": "12",         "name": "FB",         "type": "input",-        "description": "Feedback and OVP monitor for non-isolated flyback, with an OVP reference of 1.438V typical; connect to GND if not used in isolated flyback."+        "description": "OVP monitor and feedback pin for non-isolated solutions; connect FB to GND if it is not used in isolated flyback."       },       {         "number": "13",         "name": "EN/SYNC",         "type": "input",-        "description": "On/off control input with an internal 1MΩ pull-down to GND and an enable rising threshold of 1.628V typical, which can also accept an external clock above the RT-set frequency for synchronization; external pull-up current must be limited to 0.4mA."+        "description": "On/off control input with an internal 1MΩ resistor to GND; an external clock higher than the RT-set frequency applied here synchronizes the switching frequency."       },       {         "number": "14",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "15",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "16",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "17",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "18",         "name": "SS",         "type": "passive",-        "description": "Soft-start pin: a capacitor from SS to GND sets the soft-start time and hiccup protection delay, with the SS voltage clamped at 3.65V during normal operation."+        "description": "Soft start; one capacitor between SS and GND controls the COMP voltage rise and sets the hiccup protection delay."       },       {         "number": "19",         "name": "ISENSE",         "type": "input",-        "description": "Current sense and feedback mode setting pin that senses the sense resistor voltage for cycle-by-cycle current limit, with an ISENSE current limit threshold of 185mV typical."+        "description": "Current sense and isolated/non-isolated mode setting; senses the sense-resistor voltage for current-mode control, cycle-by-cycle current limit, and overload and short-circuit protection."       },       {         "number": "20",         "name": "RTN",         "type": "passive",-        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN, with an RTN on-resistance of 0.48Ω typical at 600mA."+        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN."       },       {         "number": "21",         "name": "RTN",         "type": "passive",-        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN, with an RTN on-resistance of 0.48Ω typical at 600mA."+        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN."       },       {         "number": "22",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "23",         "name": "VSS",         "type": "power_in",-        "description": "Negative power supply terminal from the PoE input power rail, which serves as the reference for VDD, DET, CLASS, T2P and RTN voltages."+        "description": "Negative power supply terminal from the PoE input power rail."       },       {         "number": "24",         "name": "VSS",         "type": "power_in",-        "description": "Negative power supply terminal from the PoE input power rail, which serves as the reference for VDD, DET, CLASS, T2P and RTN voltages."+        "description": "Negative power supply terminal from the PoE input power rail."       },       {         "number": "25",@@ -219,19 +219,19 @@         "number": "26",         "name": "CLASS",         "type": "passive",-        "description": "Classification pin: connect a resistor from CLASS to VSS to program the classification current, with a typical CLASS voltage of 1.16V in the classification range."+        "description": "Classification; a resistor from CLASS to VSS programs the classification current."       },       {         "number": "27",         "name": "T2P",         "type": "output",-        "description": "Type-2 PSE indicator, an active-low open-drain output that indicates a Type-2 PSE or wall adapter presence, with a maximum sink current of 5mA referenced to VSS."+        "description": "Open-drain Type-2 PSE indicator; pulled low to VSS indicates a Type-2 PSE or a wall adapter."       },       {         "number": "28",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "29",@@ -251,18 +251,19 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The top-view pin map on page 2 is garbled in the extracted text, so the pin-number-to-physical-locat; Pin types are not stated in the datasheet and were inferred from the function descriptions for KiCad; The datasheet lists these seven pins together as NC (not connected internally); each is listed separ",+          "extractor flagged: The page 2 top-view text extraction is garbled. Pin numbers were taken from the Pin Functions table ; The datasheet does not assign ERC pin types. Types for DET, RT, COMP, SS, RTN, FTY, CLASS (passive) ; The exposed thermal pad is not in the numbered pin list and is not included. Page 26 says to connect",           "exposed pad 29 added from the footprint"         ],         "pages_sent": 28,-        "cost_usd": 0.0326,-        "at": "2026-11-13T03:20:12"+        "cost_usd": 0.0341,+        "at": "2026-11-20T07:53:24"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/3882b88b88c12299da9dca05281e1e87.pdf",         "pages": 28,         "sha256": "620be15933636006",-        "source_tier": "lcsc"+        "source_tier": "lcsc",+        "citation": "MONOLITHIC POWER SYSTEMS (MPS) datasheet, copy hosted by LCSC"       },       "cad": "land: KiCad official (CC-BY-SA 4.0); 3D: generated from the datasheet",       "model_3d_generated": {@@ -299,8 +300,8 @@         "zmin_mm": 0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "45ef3907146575c4d5c0dc523d3bab3055b5ad4917104078307a083a9cfbe5ed",-        "checked": "2026-11-13",+        "sha256": "a9940f67cab54ab11297c1300d11a72f11060119f054a7af6370185c7a109fd7",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -318,8 +319,8 @@         "zmin_mm": 0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "37bfd4e3b0235afbd74d38d785e387e0cba0733d45d2c964d9de2681b0210ed8",-        "checked": "2026-11-13",+        "sha256": "3f3f008b0e32d29018fa8cd0993bba348eaa7025618b603f91ef64ed10215b67",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],@@ -364,5 +365,697 @@         "by": "factory/package_fit.py"       }     }+  },+  "metadata": {+    "characteristics": {+      "version": 1,+      "source": "datasheet",+      "rows": [+        {+          "name": "Voltage on VDD, RTN, DET, T2P, AUX, GND (to VSS)",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.3,+          "typ": null,+          "max": 100,+          "conditions": "Pins voltages with respect to VSS",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Voltage on CLASS, FTY (to VSS)",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.3,+          "typ": null,+          "max": 6.5,+          "conditions": "Pins voltages with respect to VSS",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Voltage on VDD (to GND)",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.3,+          "typ": null,+          "max": 100,+          "conditions": "Pins voltages with respect to GND",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Voltage on VIN (to GND)",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.3,+          "typ": null,+          "max": 40,+          "conditions": "Pins voltages with respect to GND",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Voltage on VCC, GATE (to GND)",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.3,+          "typ": null,+          "max": 15,+          "conditions": "Pins voltages with respect to GND",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Voltage on all other pins (to GND)",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.3,+          "typ": null,+          "max": 6,+          "conditions": "Pins voltages with respect to GND",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Voltage on AUX (to VDD)",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -6.5,+          "typ": null,+          "max": 0.3,+          "conditions": "Pins voltage with respect to VDD",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "T2P sink current",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": 10,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "AUX sink current",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": -5,+          "typ": null,+          "max": null,+          "conditions": "See note 3",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "PG sink current",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": 1,+          "conditions": "See note 4",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "EN/SYNC sink current",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": 0.5,+          "conditions": "See note 5",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Junction temperature",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "°C",+          "min": null,+          "typ": null,+          "max": 150,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Storage temperature",+          "symbol": "",+          "kind": "absolute_maximum",+          "unit": "°C",+          "min": -55,+          "typ": null,+          "max": 150,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Supply voltage (VDD)",+          "symbol": "VDD",+          "kind": "recommended_operating",+          "unit": "V",+          "min": 0,+          "typ": null,+          "max": 57,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "VIN voltage",+          "symbol": "VIN",+          "kind": "recommended_operating",+          "unit": "V",+          "min": 7,+          "typ": null,+          "max": 35,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Maximum T2P sink current",+          "symbol": "",+          "kind": "recommended_operating",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": 5,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Maximum AUX sink current",+          "symbol": "",+          "kind": "recommended_operating",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": -3,+          "conditions": "See note 3",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Maximum PG sink current",+          "symbol": "",+          "kind": "recommended_operating",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": 0.6,+          "conditions": "See note 4",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Maximum EN/SYNC sink current",+          "symbol": "",+          "kind": "recommended_operating",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": 0.4,+          "conditions": "See note 5",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Operating junction temp. (TJ)",+          "symbol": "TJ",+          "kind": "recommended_operating",+          "unit": "°C",+          "min": -40,+          "typ": null,+          "max": 125,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "DET leakage current",+          "symbol": "VDET-LK",+          "kind": "electrical",+          "unit": "μA",+          "min": null,+          "typ": 0.1,+          "max": 5,+          "conditions": "VDET = VDD = 57V, measure IDET",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Detection current (VDD = 2.5V)",+          "symbol": "IDET",+          "kind": "electrical",+          "unit": "μA",+          "min": 96,+          "typ": 99,+          "max": 102,+          "conditions": "VDD = 2.5V, measure ISUPPLY",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Detection current (VDD = 10.1V)",+          "symbol": "IDET",+          "kind": "electrical",+          "unit": "μA",+          "min": 395,+          "typ": 410,+          "max": 425,+          "conditions": "VDD = 10.1V, measure ISUPPLY",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "VCLASS output voltage",+          "symbol": "VCLASS",+          "kind": "electrical",+          "unit": "V",+          "min": 1.1,+          "typ": 1.16,+          "max": 1.21,+          "conditions": "13V < VDD < 21V, 1mA < ICLASS < 43mA",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Classification current, RCLASS = 578Ω",+          "symbol": "ICLASS",+          "kind": "electrical",+          "unit": "mA",+          "min": 1.8,+          "typ": 2,+          "max": 2.4,+          "conditions": "RCLASS = 578Ω, 13V ≤ VDD ≤ 21V",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Classification current, RCLASS = 110Ω",+          "symbol": "ICLASS",+          "kind": "electrical",+          "unit": "mA",+          "min": 9.9,+          "typ": 10.55,+          "max": 11.3,+          "conditions": "RCLASS = 110Ω, 13V ≤ VDD ≤ 21V",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Classification current, RCLASS = 62Ω",+          "symbol": "ICLASS",+          "kind": "electrical",+          "unit": "mA",+          "min": 17.7,+          "typ": 18.7,+          "max": 19.8,+          "conditions": "RCLASS = 62Ω, 13V ≤ VDD ≤ 21V",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Classification current, RCLASS = 41.2Ω",+          "symbol": "ICLASS",+          "kind": "electrical",+          "unit": "mA",+          "min": 26.6,+          "typ": 28.15,+          "max": 29.7,+          "conditions": "RCLASS = 41.2Ω, 13V ≤ VDD ≤ 21V",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Classification current, RCLASS = 28.7Ω",+          "symbol": "ICLASS",+          "kind": "electrical",+          "unit": "mA",+          "min": 38.2,+          "typ": 40.4,+          "max": 42.6,+          "conditions": "RCLASS = 28.7Ω, 13V ≤ VDD ≤ 21V",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Classification lower threshold",+          "symbol": "VCL-ON",+          "kind": "electrical",+          "unit": "V",+          "min": 11.8,+          "typ": 12.5,+          "max": 13,+          "conditions": "Class regulator turns on, VDD rising",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Classification upper threshold",+          "symbol": "VCL-OFF",+          "kind": "electrical",+          "unit": "V",+          "min": 21,+          "typ": 22,+          "max": 23,+          "conditions": "Class regulator turns off, VDD rising",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Mark event reset threshold",+          "symbol": "VMARK-L",+          "kind": "electrical",+          "unit": "V",+          "min": 4.5,+          "typ": 5,+          "max": 5.5,+          "conditions": "",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Max mark event voltage",+          "symbol": "VMARK-H",+          "kind": "electrical",+          "unit": "V",+          "min": 11,+          "typ": 11.5,+          "max": 12,+          "conditions": "",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Mark event current",+          "symbol": "IMARK",+          "kind": "electrical",+          "unit": "mA",+          "min": 0.5,+          "typ": 1.5,+          "max": 2,+          "conditions": "",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "IC supply current during classification",+          "symbol": "IIN-CLASS",+          "kind": "electrical",+          "unit": "μA",+          "min": null,+          "typ": 220,+          "max": 300,+          "conditions": "VDD = 17.5V, CLASS floating",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "VDD turn-on threshold",+          "symbol": "VDD-VSS-R",+          "kind": "electrical",+          "unit": "V",+          "min": 35,+          "typ": 37.5,+          "max": 40,+          "conditions": "VDD rising",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "VDD turn-off threshold",+          "symbol": "VDD-VSS-F",+          "kind": "electrical",+          "unit": "V",+          "min": 29,+          "typ": 31,+          "max": 33,+          "conditions": "VDD falling",+          "source_page": 4,+          "source": "datasheet"+        },+        {+          "name": "Leakage current (pass device)",+          "symbol": "IRTN-LK",+          "kind": "electrical",+          "unit": "μA",+          "min": null,+          "typ": 1,+          "max": 15,+          "conditions": "VDD = VRTN = 57V",+          "source_page": 5,+          "source": "datasheet"+        },+        {+          "name": "Current limit",+          "symbol": "ILIMIT",+          "kind": "electrical",+          "unit": "mA",+          "min": 720,+          "typ": 840,+          "max": 900,+          "conditions": "VRTN = 1V",+          "source_page": 5,+          "source": "datasheet"+        },+        {+          "name": "Inrush to operation mode delay",+          "symbol": "TDELAY",+          "kind": "timing",+          "unit": "ms",+          "min": null,+          "typ": 80,+          "max": 100,+          "conditions": "",+          "source_page": 5,+          "source": "datasheet"+        },+        {+          "name": "T2P output low voltage",+          "symbol": "",+          "kind": "electrical",+          "unit": "V",+          "min": null,+          "typ": 0.1,+          "max": 0.3,+          "conditions": "IT2P = 2mA, respect to VSS",+          "source_page": 5,+          "source": "datasheet"+        },+        {+          "name": "VCC UVLO threshold",+          "symbol": "VCC-UVLO",+          "kind": "electrical",+          "unit": "V",+          "min": 3.9,+          "typ": 4.17,+          "max": 4.44,+          "conditions": "Rising edge",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "VCC regulation voltage",+          "symbol": "VCC",+          "kind": "electrical",+          "unit": "V",+          "min": 10.6,+          "typ": 11.8,+          "max": 12.8,+          "conditions": "Load = 0mA to 10mA",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "Quiescent current",+          "symbol": "IQ",+          "kind": "electrical",+          "unit": "mA",+          "min": null,+          "typ": 0.4,+          "max": 0.6,+          "conditions": "VFB = 1.35V, test supply from VIN to GND",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "ISENSE limit",+          "symbol": "VLIMIT",+          "kind": "electrical",+          "unit": "mV",+          "min": 163,+          "typ": 185,+          "max": 206,+          "conditions": "TJ = 25°C",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "Minimum on time",+          "symbol": "TON",+          "kind": "timing",+          "unit": "ns",+          "min": null,+          "typ": 214,+          "max": 400,+          "conditions": "",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "Maximum duty cycle",+          "symbol": "DMAX",+          "kind": "electrical",+          "unit": "%",+          "min": null,+          "typ": 93,+          "max": 95,+          "conditions": "RT = 6.81kΩ",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "Switching frequency (RT = 6.81kΩ)",+          "symbol": "FSW",+          "kind": "electrical",+          "unit": "kHz",+          "min": 308,+          "typ": 337,+          "max": 363,+          "conditions": "RT = 6.81kΩ",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "Switching frequency (RT = 80.6kΩ)",+          "symbol": "FSW",+          "kind": "electrical",+          "unit": "kHz",+          "min": 25,+          "typ": 30,+          "max": 35,+          "conditions": "RT = 80.6kΩ",+          "source_page": 6,+          "source": "datasheet"+        },+        {+          "name": "FB reference voltage (TJ = 25°C)",+          "symbol": "VFB",+          "kind": "electrical",+          "unit": "V",+          "min": 1.222,+          "typ": 1.237,+          "max": 1.252,+          "conditions": "TJ = 25°C",+          "source_page": 7,+          "source": "datasheet"+        },+        {+          "name": "FB reference voltage (TJ = -40°C to 125°C)",+          "symbol": "VFB",+          "kind": "electrical",+          "unit": "V",+          "min": 1.211,+          "typ": 1.237,+          "max": 1.258,+          "conditions": "TJ = -40°C to 125°C",+          "source_page": 7,+          "source": "datasheet"+        },+        {+          "name": "FB bias current",+          "symbol": "IFB",+          "kind": "electrical",+          "unit": "μA",+          "min": null,+          "typ": 0.01,+          "max": 0.15,+          "conditions": "VFB = 1.237V, TJ = 25°C",+          "source_page": 7,+          "source": "datasheet"+        },+        {+          "name": "OVP reference level",+          "symbol": "VOVP",+          "kind": "electrical",+          "unit": "V",+          "min": 1.391,+          "typ": 1.438,+          "max": 1.479,+          "conditions": "",+          "source_page": 7,+          "source": "datasheet"+        },+        {+          "name": "Enable rising threshold",+          "symbol": "VEN-RISING",+          "kind": "electrical",+          "unit": "V",+          "min": 1.463,+          "typ": 1.628,+          "max": 1.793,+          "conditions": "TJ = 25°C",+          "source_page": 7,+          "source": "datasheet"+        },+        {+          "name": "Enable input current",+          "symbol": "IEN",+          "kind": "electrical",+          "unit": "μA",+          "min": null,+          "typ": 2.5,+          "max": 5,+          "conditions": "VEN = 3V",+          "source_page": 7,+          "source": "datasheet"+        },+        {+          "name": "Thermal resistance, junction-to-ambient (QFN-28 4mmx5mm)",+          "symbol": "θJA",+          "kind": "thermal",+          "unit": "°C/W",+          "min": null,+          "typ": 40,+          "max": null,+          "conditions": "Measured on JESD51-7, 2-layer PCB",+          "source_page": 3,+          "source": "datasheet"+        },+        {+          "name": "Thermal resistance, junction-to-case (QFN-28 4mmx5mm)",+          "symbol": "θJC",+          "kind": "thermal",+          "unit": "°C/W",+          "min": null,+          "typ": 9,+          "max": null,+          "conditions": "",+          "source_page": 3,+          "source": "datasheet"+        }+      ]+    }   } }
page.json+42−46
@@ -4,7 +4,7 @@   "slug": "mp8008gv-z",   "title": "MP8008GV-Z",   "brief": "MONOLITHIC POWER SYSTEMS (MPS) Global Sourcing Parts, QFN-28(4x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.1",+  "version": "0.1.2",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -36,7 +36,7 @@       "mouser": "946-MP8008GV-Z"     },     "distributor_check": {-      "checked_at": "2026-11-13T03:20:24Z",+      "checked_at": "2026-11-20T07:53:39Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "1589-1728-2-ND",@@ -52,145 +52,145 @@         "number": "1",         "name": "AUX",         "type": "input",-        "description": "Auxiliary power input detector: driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active."+        "description": "Auxiliary power input detector; driving VDD - AUX above 2.3V disables the hot-swap MOSFET and CLASS functions and forces T2P and PG active."       },       {         "number": "2",         "name": "DET",         "type": "passive",-        "description": "Detection pin: connect a 24.9kΩ (±1%) resistor between VDD and DET for the PoE detection signature, with a valid signature resistance of 23.7kΩ to 26.3kΩ."+        "description": "Detection pin; a 24.9kΩ resistor must be connected between VDD and DET for PoE detection."       },       {         "number": "3",         "name": "VDD",         "type": "power_in",-        "description": "Positive power supply terminal from the PoE input power rail, with a recommended supply voltage of 0V to 57V and an absolute maximum of -0.3V to +100V."+        "description": "Positive power supply terminal from the PoE input power rail."       },       {         "number": "4",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "5",         "name": "PG",         "type": "output",-        "description": "PD supply power good indicator, pulled up by an internal current source when the PD output capacitor is fully charged; connect to EN/SYNC for flyback automatic start-up, with a recommended PG sink current of no more than 0.6mA."+        "description": "Power-good indicator pulled up by an internal current source when the PD output capacitor is fully charged; connect PG to EN/SYNC for flyback automatic start-up."       },       {         "number": "6",         "name": "GATE",         "type": "output",-        "description": "Gate driving signal that drives the external N-channel power MOSFET, with a sourcing impedance of 4.1Ω and a sinking impedance of 2Ω."+        "description": "Gate driving signal that drives the external N-channel power MOSFET."       },       {         "number": "7",         "name": "VCC",         "type": "power_out",-        "description": "Flyback controller internal 12V regulator output, supplied through an internal LDO from VIN, which must be bypassed with a capacitor of no less than 1µF."+        "description": "Output of the flyback controller internal 12V regulator, powered through an internal LDO from VIN; a capacitor must be connected between VCC and GND."       },       {         "number": "8",         "name": "VIN",         "type": "power_in",-        "description": "Flyback controller input supply, operating from 7V to 35V, with a bypass capacitor connected from VIN to GND."+        "description": "Flyback controller input supply; connect a bypass capacitor from VIN to GND."       },       {         "number": "9",         "name": "GND",         "type": "power_in",-        "description": "Power ground and gate driver return; GND must be connected to RTN and the exposed pad must be connected to GND."+        "description": "Power ground; the gate driver return pin."       },       {         "number": "10",         "name": "RT",         "type": "passive",-        "description": "Switching frequency set: a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz."+        "description": "Switching frequency set; a resistor from RT to GND sets the switching frequency between 30kHz and 400kHz."       },       {         "number": "11",         "name": "COMP",-        "type": "bidirectional",-        "description": "Feedback input for isolated flyback and error amplifier output for non-isolated solutions, which requires an R-C compensation network in non-isolated mode."+        "type": "passive",+        "description": "Feedback for isolated flyback; COMP is the error amplifier output pin for non-isolated solutions."       },       {         "number": "12",         "name": "FB",         "type": "input",-        "description": "Feedback and OVP monitor for non-isolated flyback, with an OVP reference of 1.438V typical; connect to GND if not used in isolated flyback."+        "description": "OVP monitor and feedback pin for non-isolated solutions; connect FB to GND if it is not used in isolated flyback."       },       {         "number": "13",         "name": "EN/SYNC",         "type": "input",-        "description": "On/off control input with an internal 1MΩ pull-down to GND and an enable rising threshold of 1.628V typical, which can also accept an external clock above the RT-set frequency for synchronization; external pull-up current must be limited to 0.4mA."+        "description": "On/off control input with an internal 1MΩ resistor to GND; an external clock higher than the RT-set frequency applied here synchronizes the switching frequency."       },       {         "number": "14",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "15",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "16",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "17",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "18",         "name": "SS",         "type": "passive",-        "description": "Soft-start pin: a capacitor from SS to GND sets the soft-start time and hiccup protection delay, with the SS voltage clamped at 3.65V during normal operation."+        "description": "Soft start; one capacitor between SS and GND controls the COMP voltage rise and sets the hiccup protection delay."       },       {         "number": "19",         "name": "ISENSE",         "type": "input",-        "description": "Current sense and feedback mode setting pin that senses the sense resistor voltage for cycle-by-cycle current limit, with an ISENSE current limit threshold of 185mV typical."+        "description": "Current sense and isolated/non-isolated mode setting; senses the sense-resistor voltage for current-mode control, cycle-by-cycle current limit, and overload and short-circuit protection."       },       {         "number": "20",         "name": "RTN",         "type": "passive",-        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN, with an RTN on-resistance of 0.48Ω typical at 600mA."+        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN."       },       {         "number": "21",         "name": "RTN",         "type": "passive",-        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN, with an RTN on-resistance of 0.48Ω typical at 600mA."+        "description": "Drain of the PD hot-swap MOSFET; connect GND and the flyback power return to RTN."       },       {         "number": "22",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "23",         "name": "VSS",         "type": "power_in",-        "description": "Negative power supply terminal from the PoE input power rail, which serves as the reference for VDD, DET, CLASS, T2P and RTN voltages."+        "description": "Negative power supply terminal from the PoE input power rail."       },       {         "number": "24",         "name": "VSS",         "type": "power_in",-        "description": "Negative power supply terminal from the PoE input power rail, which serves as the reference for VDD, DET, CLASS, T2P and RTN voltages."+        "description": "Negative power supply terminal from the PoE input power rail."       },       {         "number": "25",@@ -202,19 +202,19 @@         "number": "26",         "name": "CLASS",         "type": "passive",-        "description": "Classification pin: connect a resistor from CLASS to VSS to program the classification current, with a typical CLASS voltage of 1.16V in the classification range."+        "description": "Classification; a resistor from CLASS to VSS programs the classification current."       },       {         "number": "27",         "name": "T2P",         "type": "output",-        "description": "Type-2 PSE indicator, an active-low open-drain output that indicates a Type-2 PSE or wall adapter presence, with a maximum sink current of 5mA referenced to VSS."+        "description": "Open-drain Type-2 PSE indicator; pulled low to VSS indicates a Type-2 PSE or a wall adapter."       },       {         "number": "28",         "name": "NC",         "type": "unconnected",-        "description": "Not connected internally; connect to GND during layout."+        "description": "Not connected internally; connect NC to GND during layout."       },       {         "number": "29",@@ -234,18 +234,19 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The top-view pin map on page 2 is garbled in the extracted text, so the pin-number-to-physical-locat; Pin types are not stated in the datasheet and were inferred from the function descriptions for KiCad; The datasheet lists these seven pins together as NC (not connected internally); each is listed separ",+          "extractor flagged: The page 2 top-view text extraction is garbled. Pin numbers were taken from the Pin Functions table ; The datasheet does not assign ERC pin types. Types for DET, RT, COMP, SS, RTN, FTY, CLASS (passive) ; The exposed thermal pad is not in the numbered pin list and is not included. Page 26 says to connect",           "exposed pad 29 added from the footprint"         ],         "pages_sent": 28,-        "cost_usd": 0.0326,-        "at": "2026-11-13T03:20:12"+        "cost_usd": 0.0341,+        "at": "2026-11-20T07:53:24"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/3882b88b88c12299da9dca05281e1e87.pdf",         "pages": 28,         "sha256": "620be15933636006",-        "source_tier": "lcsc"+        "source_tier": "lcsc",+        "citation": "MONOLITHIC POWER SYSTEMS (MPS) datasheet, copy hosted by LCSC"       },       "cad": "land: KiCad official (CC-BY-SA 4.0); 3D: generated from the datasheet",       "model_3d_generated": {@@ -282,8 +283,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "45ef3907146575c4d5c0dc523d3bab3055b5ad4917104078307a083a9cfbe5ed",-        "checked": "2026-11-13",+        "sha256": "a9940f67cab54ab11297c1300d11a72f11060119f054a7af6370185c7a109fd7",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -301,8 +302,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "37bfd4e3b0235afbd74d38d785e387e0cba0733d45d2c964d9de2681b0210ed8",-        "checked": "2026-11-13",+        "sha256": "3f3f008b0e32d29018fa8cd0993bba348eaa7025618b603f91ef64ed10215b67",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],@@ -349,16 +350,9 @@     }   },   "metadata": {-    "specs": {-      "Manufacturer": "MONOLITHIC POWER SYSTEMS (MPS)",-      "Package": "QFN-28(4x5)",-      "Category": "Global Sourcing Parts",-      "Pins": "29"-    },     "characteristics": {       "version": 1,       "source": "datasheet",-      "datasheet_sha256": "620be1593363600645be31c51aeaded7630c958c0a370803d4efdff6569e4a77",       "rows": [         {           "name": "Voltage on VDD, RTN, DET, T2P, AUX, GND (to VSS)",@@ -1085,5 +1079,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "MONOLITHIC POWER SYSTEMS (MPS) Global Sourcing Parts, QFN-28(4x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file