Generated by kicad-footprint-generator · KiCad file format 20260206
MIC2800-G1JSYML-TR
Microchip Tech · Power Management Specialized - PMIC · QFN-16(3x3)
MIC2800-G1JSYML-TR from Microchip Tech, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LOWQ | input | LOWQ mode control input: logic high (>1V) = full power PWM mode, logic low (<0.2V) = LOWQ mode; do not leave floating. |
| 2 | BIAS | passive | Internal circuit bias supply, powered from VIN through an internal 6Ω resistor; decouple to signal ground with a 0.1 µF capacitor and do not load. |
| 3 | SGND | power_in | Signal ground for the biasing and control circuitry. |
| 4 | PGND | power_in | Power ground for the high-current PWM mode. |
| 5 | SW | output | Switch output of the internal power MOSFETs, connects directly to the inductor. |
| 6 | VIN | power_in | Supply input for the DC/DC converter (2.7V to 5.5V); must be tied to pin 7 externally, with a 4.7 µF minimum ceramic capacitor recommended close to it. |
| 7 | VIN | power_in | Supply input for LDO2; must be tied to pin 6 externally. |
| 8 | LDO2 | output | Output of LDO regulator 2, 300 mA capable, with minimum recommended 2.2 µF ceramic output capacitance. |
| 9 | FB | input | Feedback input to the DC/DC error amplifier; for fixed output versions connect directly to VOUT. |
| 10 | LDO | passive | Output of the LOWQ-mode linear regulator; connect to the DC/DC VOUT, and it also supplies LDO1 in PWM mode. |
| 11 | LDO1 | output | Output of LDO regulator 1, powered from the DC/DC output, with minimum recommended 2.2 µF ceramic output capacitance. |
| 12 | POR | output | Open-drain active-low power-on reset output indicating undervoltage on the regulated outputs; requires a pull-up resistor. |
| 13 | CSET | passive | POR delay set pin: external capacitor to GND sets the delay (µs equals capacitance in pF, up to 1 s); left open gives minimum delay and the pin cannot be grounded. |
| 14 | CBYP | passive | Reference bypass: external 0.1 µF to GND reduces output noise; may be left open. |
| 15 | EN1 | input | Active-high enable for the DC/DC converter and LDO1 (VIH min 1.0V); do not leave floating. |
| 16 | EN2 | input | Active-high enable for LDO2 (VIH min 1.0V); do not leave floating. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-16(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| UVLO Threshold | UVLOTH | 2.45 | 2.55 | 2.65 | V | Rising input voltage during turn on | 4 |
| Ground Pin Current in Shutdown | IGND_SHDN | 0.2 | 5 | µA | All EN = 0V | 4 | |
| Enable Input Voltage Logic Low | VIH | 0.2 | V | 4 | |||
| Enable Input Voltage Logic High | VIL | 1 | V | 4 | |||
| Enable Input Current (low) | IENLK | 0.1 | 1 | µA | VIL ≤ 0.2V | 4 | |
| Enable Input Current (high) | IENLK | 0.1 | 1 | µA | VIH ≥1.0V | 4 | |
| Turn-on Time (DC/DC) | tTURN-ON | 83 | 350 | µs | EN2 = VIN; ILOAD = 300 mA; CBYP = 0.1 µF | 4 | |
| POR Threshold Voltage, Failing | VTHLOW_POR | 90 | 91 | % | Low Threshold, % of nominal (Flag ON) | 4 | |
| POR Threshold Voltage, Rising | VTHIGH_POR | 96 | 99 | % | High Threshold, % of nominal (Flag OFF) | 4 | |
| POR Output Logic Low Voltage | VOLPOR | 10 | 100 | mV | IL = 250 µA | 4 | |
| POR Flag Leakage Current | ILEAKPOR | 0.01 | 1 | µA | Flag OFF | 4 | |
| CSET Pin Current Source | ICSET | 0.75 | 1.25 | 1.75 | µA | VCSET = 0V | 4 |
| DC/DC Output Voltage Accuracy (full power) | VOUT | -2 | 2 | % | Fixed Output Voltages | 5 | |
| DC/DC Output Voltage Accuracy (full power, -40 to +125°C) | VOUT | -3 | 3 | % | Fixed Output Voltages | 5 | |
| DC/DC Current Limit in PWM Mode | ILIM | 0.75 | 1 | 1.6 | A | VOUT = 0.9*VNOM | 5 |
| DC/DC FB pin input current (ADJ only) | IFB | 1 | 5 | nA | 5 | ||
| DC/DC Load Regulation (full power) | ∆VOUT/VOUT | 0.2 | 1.5 | % | 20 mA < ILOAD < 300 mA | 5 | |
| Maximum Duty Cycle | DCMAX | 100 | % | VFB ≤ 0.4V | 5 | ||
| Oscillator Frequency | fosc | 1.8 | 2 | 2.2 | MHz | 5 | |
| DC/DC Output Accuracy (LOWQ) | VOUT | -2 | 2 | % | Variation from nominal VOUT | 5 | |
| DC/DC Output Accuracy (LOWQ, -40 to +125°C) | VOUT | -3 | 3 | % | Variation from nominal VOUT; -40°C to +125°C | 5 | |
| DC/DC Line Regulation (LOWQ) | (∆VOUT/VOUT)/∆VIN | 0.02 | 0.6 | %/V | VIN = VOUT + 1V to 5.5V; IOUT = 100 µA | 5 | |
| DC/DC Load Regulation (LOWQ) | ∆VOUT/VOUT | 0.2 | 1.5 | % | IOUT = 100 µA to 50 mA | 5 | |
| DC/DC Current Limit (LOWQ) | ILIM_LOWQ | 80 | 120 | 190 | mA | VOUT = 0V | 5 |
| LDO1 Output Accuracy (full power) | VOUT | -2 | 2 | % | Variation from nominal VOUT | 6 | |
| LDO1 Output Accuracy (full power, -40 to +125°C) | VOUT | -3 | 3 | % | Variation from nominal VOUT; -40°C to +125°C | 6 | |
| LDO1 Output Current Capability | IOUT | 300 | mA | VIN ≥ 1.8V | 6 | ||
| LDO1 Output Current Capability | IOUT | 120 | mA | VIN ≥ 1.5V | 6 | ||
| LDO1 Current Limit | ILIM | 350 | 500 | 700 | mA | VOUT = 0V | 6 |
| LDO1 Output Accuracy (LOWQ) | VOUT | -3 | 3 | % | Variation from nominal VOUT | 6 | |
| LDO1 Output Accuracy (LOWQ, -40 to +125°C) | VOUT | -4 | 4 | % | Variation from nominal VOUT; -40°C to +125°C | 6 | |
| LDO1 Load Regulation (LOWQ) | ∆VOUT/VOUT | 0.2 | 1 | % | IOUT = 100 µA to 10 mA | 6 | |
| LDO1 Current Limit (LOWQ) | ILIM | 50 | 85 | 125 | mA | VOUT = 0V | 6 |
| LDO2 Output Accuracy (full power) | VOUT | -2 | 2 | % | Variation from nominal VOUT | 7 | |
| LDO2 Output Accuracy (full power, -40 to +125°C) | VOUT | -3 | 3 | % | Variation from nominal VOUT; -40°C to +125°C | 7 | |
| LDO2 Line Regulation (full power) | (∆VOUT/VOUT)/∆VIN | 0.02 | 0.6 | %/V | VIN = VOUT +1V to 5.5V; IOUT = 100 µA | 7 | |
| LDO2 Current Limit | ILIM | 400 | 550 | 850 | mA | VOUT = 0V | 7 |
| LDO2 Output Accuracy (LOWQ) | VOUT | -3 | 3 | % | Variation from nominal VOUT | 7 | |
| LDO2 Output Accuracy (LOWQ, -40 to +125°C) | VOUT | -4 | 4 | % | Variation from nominal VOUT; -40°C to +125°C | 7 | |
| LDO2 Line Regulation (LOWQ) | (∆VOUT/VOUT)/∆VIN | 0.02 | 0.6 | %/V | VIN = VOUT +1V to 5.5V | 7 | |
| LDO2 Load Regulation (LOWQ) | ∆VOUT/VOUT | 0.2 | 1 | % | IOUT = 100 µA to 10 mA | 7 | |
| LDO2 Dropout Voltage (LOWQ) | VDO | 22 | 50 | mV | IOUT = 10 mA; VOUTLDO2 >= 2.7V | 7 | |
| LDO2 Current Limit (LOWQ) | ILIM | 50 | 85 | 125 | mA | VIN = 2.7V; VOUT = 0V | 7 |
| Supply Voltage (absolute maximum) | VIN | -0.3 | 6 | V | 3 | ||
| Enable Input Voltage (absolute maximum) | VEN1, EN2 | -0.3 | V | Max printed as VIN + 0.3V | 3 | ||
| LOWQ, POR voltage (absolute maximum) | -0.3 | 6 | V | 3 | |||
| Lead Temperature (soldering) | 260 | °C | 10 sec. | 3 | |||
| Storage Temperature | TS | -65 | 150 | °C | 3 | ||
| ESD Rating | 2 | kV | Human body model, 1.5 kΩ in series with 100 pF | 3 | |||
| Supply Voltage (operating) | VIN | 2.7 | 5.5 | V | 3 | ||
| Enable Input Voltage (operating) | VEN1, EN2 | 0 | V | Max printed as +VIN | 3 | ||
| LOWQ, POR voltage (operating) | 0 | 5.5 | V | 3 | |||
| Junction Temperature | TJ | -40 | 125 | °C | 3 | ||
| Junction Thermal Resistance QFN-16 | θJA | 45 | °C/W | 8 | |||
| UVLO Hysteresis | UVLOHYS | 100 | mV | 4 | |||
| Overtemperature Shutdown | TSD | 160 | °C | 4 |
CAD (KiCad official)
- Symbol:
MIC2800-G1JSYML-TR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
mic2800-g1jsyml-tr-etched.step/mic2800-g1jsyml-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic2800-g1jsyml-tr.step/mic2800-g1jsyml-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (30 pp, sha256
6e374b5182424e57, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).