Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MIC2800-G1JSYML-TR

Microchip Tech · Power Management Specialized - PMIC · QFN-16(3x3)

MIC2800-G1JSYML-TR from Microchip Tech, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 LOWQ input LOWQ mode control input: logic high (>1V) = full power PWM mode, logic low (<0.2V) = LOWQ mode; do not leave floating.
2 BIAS passive Internal circuit bias supply, powered from VIN through an internal 6Ω resistor; decouple to signal ground with a 0.1 µF capacitor and do not load.
3 SGND power_in Signal ground for the biasing and control circuitry.
4 PGND power_in Power ground for the high-current PWM mode.
5 SW output Switch output of the internal power MOSFETs, connects directly to the inductor.
6 VIN power_in Supply input for the DC/DC converter (2.7V to 5.5V); must be tied to pin 7 externally, with a 4.7 µF minimum ceramic capacitor recommended close to it.
7 VIN power_in Supply input for LDO2; must be tied to pin 6 externally.
8 LDO2 output Output of LDO regulator 2, 300 mA capable, with minimum recommended 2.2 µF ceramic output capacitance.
9 FB input Feedback input to the DC/DC error amplifier; for fixed output versions connect directly to VOUT.
10 LDO passive Output of the LOWQ-mode linear regulator; connect to the DC/DC VOUT, and it also supplies LDO1 in PWM mode.
11 LDO1 output Output of LDO regulator 1, powered from the DC/DC output, with minimum recommended 2.2 µF ceramic output capacitance.
12 POR output Open-drain active-low power-on reset output indicating undervoltage on the regulated outputs; requires a pull-up resistor.
13 CSET passive POR delay set pin: external capacitor to GND sets the delay (µs equals capacitance in pF, up to 1 s); left open gives minimum delay and the pin cannot be grounded.
14 CBYP passive Reference bypass: external 0.1 µF to GND reduces output noise; may be left open.
15 EN1 input Active-high enable for the DC/DC converter and LDO1 (VIH min 1.0V); do not leave floating.
16 EN2 input Active-high enable for LDO2 (VIH min 1.0V); do not leave floating.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-16(3x3)
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
UVLO Threshold UVLOTH 2.45 2.55 2.65 V Rising input voltage during turn on 4
Ground Pin Current in Shutdown IGND_SHDN 0.2 5 µA All EN = 0V 4
Enable Input Voltage Logic Low VIH 0.2 V 4
Enable Input Voltage Logic High VIL 1 V 4
Enable Input Current (low) IENLK 0.1 1 µA VIL ≤ 0.2V 4
Enable Input Current (high) IENLK 0.1 1 µA VIH ≥1.0V 4
Turn-on Time (DC/DC) tTURN-ON 83 350 µs EN2 = VIN; ILOAD = 300 mA; CBYP = 0.1 µF 4
POR Threshold Voltage, Failing VTHLOW_POR 90 91 % Low Threshold, % of nominal (Flag ON) 4
POR Threshold Voltage, Rising VTHIGH_POR 96 99 % High Threshold, % of nominal (Flag OFF) 4
POR Output Logic Low Voltage VOLPOR 10 100 mV IL = 250 µA 4
POR Flag Leakage Current ILEAKPOR 0.01 1 µA Flag OFF 4
CSET Pin Current Source ICSET 0.75 1.25 1.75 µA VCSET = 0V 4
DC/DC Output Voltage Accuracy (full power) VOUT -2 2 % Fixed Output Voltages 5
DC/DC Output Voltage Accuracy (full power, -40 to +125°C) VOUT -3 3 % Fixed Output Voltages 5
DC/DC Current Limit in PWM Mode ILIM 0.75 1 1.6 A VOUT = 0.9*VNOM 5
DC/DC FB pin input current (ADJ only) IFB 1 5 nA 5
DC/DC Load Regulation (full power) ∆VOUT/VOUT 0.2 1.5 % 20 mA < ILOAD < 300 mA 5
Maximum Duty Cycle DCMAX 100 % VFB ≤ 0.4V 5
Oscillator Frequency fosc 1.8 2 2.2 MHz 5
DC/DC Output Accuracy (LOWQ) VOUT -2 2 % Variation from nominal VOUT 5
DC/DC Output Accuracy (LOWQ, -40 to +125°C) VOUT -3 3 % Variation from nominal VOUT; -40°C to +125°C 5
DC/DC Line Regulation (LOWQ) (∆VOUT/VOUT)/∆VIN 0.02 0.6 %/V VIN = VOUT + 1V to 5.5V; IOUT = 100 µA 5
DC/DC Load Regulation (LOWQ) ∆VOUT/VOUT 0.2 1.5 % IOUT = 100 µA to 50 mA 5
DC/DC Current Limit (LOWQ) ILIM_LOWQ 80 120 190 mA VOUT = 0V 5
LDO1 Output Accuracy (full power) VOUT -2 2 % Variation from nominal VOUT 6
LDO1 Output Accuracy (full power, -40 to +125°C) VOUT -3 3 % Variation from nominal VOUT; -40°C to +125°C 6
LDO1 Output Current Capability IOUT 300 mA VIN ≥ 1.8V 6
LDO1 Output Current Capability IOUT 120 mA VIN ≥ 1.5V 6
LDO1 Current Limit ILIM 350 500 700 mA VOUT = 0V 6
LDO1 Output Accuracy (LOWQ) VOUT -3 3 % Variation from nominal VOUT 6
LDO1 Output Accuracy (LOWQ, -40 to +125°C) VOUT -4 4 % Variation from nominal VOUT; -40°C to +125°C 6
LDO1 Load Regulation (LOWQ) ∆VOUT/VOUT 0.2 1 % IOUT = 100 µA to 10 mA 6
LDO1 Current Limit (LOWQ) ILIM 50 85 125 mA VOUT = 0V 6
LDO2 Output Accuracy (full power) VOUT -2 2 % Variation from nominal VOUT 7
LDO2 Output Accuracy (full power, -40 to +125°C) VOUT -3 3 % Variation from nominal VOUT; -40°C to +125°C 7
LDO2 Line Regulation (full power) (∆VOUT/VOUT)/∆VIN 0.02 0.6 %/V VIN = VOUT +1V to 5.5V; IOUT = 100 µA 7
LDO2 Current Limit ILIM 400 550 850 mA VOUT = 0V 7
LDO2 Output Accuracy (LOWQ) VOUT -3 3 % Variation from nominal VOUT 7
LDO2 Output Accuracy (LOWQ, -40 to +125°C) VOUT -4 4 % Variation from nominal VOUT; -40°C to +125°C 7
LDO2 Line Regulation (LOWQ) (∆VOUT/VOUT)/∆VIN 0.02 0.6 %/V VIN = VOUT +1V to 5.5V 7
LDO2 Load Regulation (LOWQ) ∆VOUT/VOUT 0.2 1 % IOUT = 100 µA to 10 mA 7
LDO2 Dropout Voltage (LOWQ) VDO 22 50 mV IOUT = 10 mA; VOUTLDO2 >= 2.7V 7
LDO2 Current Limit (LOWQ) ILIM 50 85 125 mA VIN = 2.7V; VOUT = 0V 7
Supply Voltage (absolute maximum) VIN -0.3 6 V 3
Enable Input Voltage (absolute maximum) VEN1, EN2 -0.3 V Max printed as VIN + 0.3V 3
LOWQ, POR voltage (absolute maximum) -0.3 6 V 3
Lead Temperature (soldering) 260 °C 10 sec. 3
Storage Temperature TS -65 150 °C 3
ESD Rating 2 kV Human body model, 1.5 kΩ in series with 100 pF 3
Supply Voltage (operating) VIN 2.7 5.5 V 3
Enable Input Voltage (operating) VEN1, EN2 0 V Max printed as +VIN 3
LOWQ, POR voltage (operating) 0 5.5 V 3
Junction Temperature TJ -40 125 °C 3
Junction Thermal Resistance QFN-16 θJA 45 °C/W 8
UVLO Hysteresis UVLOHYS 100 mV 4
Overtemperature Shutdown TSD 160 °C 4

CAD (KiCad official)

  • Symbol: MIC2800-G1JSYML-TR
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: mic2800-g1jsyml-tr-etched.step / mic2800-g1jsyml-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic2800-g1jsyml-tr.step / mic2800-g1jsyml-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (30 pp, sha256 6e374b5182424e57, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF