Generated by kicad-footprint-generator · KiCad file format 20260206
MCP3561-E
Microchip Tech · Analog To Digital Converters (ADCs) · TSSOP-20
MCP3561-E from Microchip Tech, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVDD | power_in | Analog supply pin, to be kept within the Electrical Characteristics range of 2.7 V to 3.6 V, with a 10 µF ceramic in parallel with a 0.1 µF ceramic recommended for bypass. |
| 2 | AGND | power_in | Analog ground, to be connected to the same ground as DGND (preferably star connection) and not internally connected to DGND. |
| 3 | REFIN- | input | Inverting differential reference input (VREF-); tie to AGND for single-ended reference use, and keep 0.6 V ≤ VREF ≤ AVDD. |
| 4 | REFIN+ | input | Noninverting differential reference input (VREF+); must satisfy 0.6 V ≤ VREF ≤ AVDD, with 0.1 µF and 10 µF bypass to AGND recommended. |
| 5 | CH0 | input | Analog input 0, selectable as VIN+ or VIN- by the multiplexer; pin voltage must stay between AGND - 0.1 V and VDD + 0.1 V. |
| 6 | CH1 | input | Analog input 1, selectable as VIN+ or VIN- by the multiplexer; pin voltage must stay between AGND - 0.1 V and VDD + 0.1 V. |
| 7 | NC | unconnected | Not connected for the MCP3561 (no internal function stated). |
| 8 | NC | unconnected | Not connected for the MCP3561 (no internal function stated). |
| 9 | NC | unconnected | Not connected for the MCP3561 (no internal function stated). |
| 10 | NC | unconnected | Not connected for the MCP3561 (no internal function stated). |
| 11 | NC | unconnected | Not connected for the MCP3561 (no internal function stated). |
| 12 | NC | unconnected | Not connected for the MCP3561 (no internal function stated). |
| 13 | CS | input | SPI chip select (Schmitt-triggered); communication starts on the falling edge and ends on the rising edge, and no communication occurs while high. |
| 14 | SCK | input | SPI serial clock input (Schmitt-triggered), maximum 20 MHz, with data latched in on the rising edge and clocked out on the falling edge. |
| 15 | SDI | input | SPI serial data input (Schmitt-triggered), latching data on the SCK rising edge; command byte is clocked in just after CS falls. |
| 16 | SDO | tri_state | SPI serial data output, clocked out on the SCK falling edge, and high-impedance when CS is high or during write/Fast command periods after the command byte. |
| 17 | IRQ/MDAT | output | Digital output configured by IRQ_MODE[1] as interrupt output (inactive state high-Z or logic high per IRQ_MODE[0]) or modulator data output; in high-Z mode an external pull-up of about 100-200 kΩ to DVDD is required. |
| 18 | MCLK | bidirectional | Master clock input for the ADC or analog master clock (AMCLK) output depending on CLK_SEL bits; typical frequency 4.9152 MHz and required continuously during conversions. |
| 19 | DGND | power_in | Digital ground for internal digital circuitry, to be connected to the same ground as AGND and not internally connected to AGND. |
| 20 | DVDD | power_in | Digital supply for internal digital circuitry, to be kept within the Electrical Characteristics range of 1.8 V to 3.6 V, with a 10 µF ceramic in parallel with a 0.1 µF ceramic recommended for bypass. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TSSOP-20 |
| Category | Data Converters |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DVDD, AVDD supply voltage | DVDD, AVDD | -0.3 | 4 | V | 5 | ||
| Digital inputs and outputs w.r.t. DGND | -0.3 | V | 5 | ||||
| Analog inputs w.r.t. AGND | -0.3 | V | 5 | ||||
| Current at input pins | -5 | 5 | mA | 5 | |||
| Current at output and supply pins | -20 | 20 | mA | 5 | |||
| Storage temperature | -65 | 150 | °C | 5 | |||
| Ambient temperature with power applied | -65 | 125 | °C | 5 | |||
| Maximum junction temperature (TJ) | TJ | 150 | °C | 5 | |||
| ESD on all pins | 6 | kV | HBM | 5 | |||
| Analog Operating Voltage | AVDD | 2.7 | 3.6 | V | 6 | ||
| Digital Operating Voltage | DVDD | 1.8 | V | DVDD ≤ 3.6V | 6 | ||
| Operating Temperature Range | TA | -40 | 125 | °C | 10 | ||
| Analog Operating Current | AIDD | 0.56 | 0.81 | mA | BOOST[1:0] = 00, 0.5x | 6 | |
| Analog Operating Current | AIDD | 0.69 | 0.96 | mA | BOOST[1:0] = 01, 0.66x | 6 | |
| Analog Operating Current | AIDD | 0.93 | 1.3 | mA | BOOST[1:0] = 10, 1x | 6 | |
| Analog Operating Current | AIDD | 1.65 | 2.2 | mA | BOOST[1:0] = 11, 2x | 6 | |
| Digital Operating Current | DIDD | 0.25 | 0.37 | mA | Note 8 | 6 | |
| Analog Partial Shutdown Current | AIDDS_PS | 22 | µA | 6 | |||
| Digital Partial Shutdown Current | DIDDS_PS | 158 | µA | 6 | |||
| Analog Full Shutdown Current | AIDDS_FS | 0.83 | µA | CONFIG0 = 0x00, TA = +105°C, MCLK input in Idle mode (Note 2) | 6 | ||
| Analog Full Shutdown Current | AIDDS_FS | 1.1 | µA | CONFIG0 = 0x00, TA = +125°C, MCLK input in Idle mode | 6 | ||
| Digital Full Shutdown Current | DIDDS_FS | 2.4 | µA | CONFIG0 = 0x00, TA = +105°C, MCLK input in Idle mode (Note 2) | 6 | ||
| Digital Full Shutdown Current | DIDDS_FS | 5 | µA | CONFIG0 = 0x00, TA = +125°C, MCLK input in Idle mode | 6 | ||
| Analog Input Leakage Current During ADC Shutdown | ILI_A | -10 | 10 | nA | 7 | ||
| Reference Voltage Range (VREF+, VREF-) | VREF | 0.6 | V | 7 | |||
| Resolution | 24 | Bits | OSR ≥ 256 (Note 1) | 7 | |||
| Gain Error | GE | -3 | 3 | % | Note 6 | 7 | |
| Gain Error Temperature Coefficient | GE_DRIFT | 0.5 | 2 | ppm/°C | GAIN: 1x, 2x, 4x (Note 2) | 7 | |
| Gain Error Temperature Coefficient | GE_DRIFT | 1 | 4 | ppm/°C | GAIN: 8x (Note 2) | 7 | |
| Gain Error Temperature Coefficient | GE_DRIFT | 2 | 8 | ppm/°C | GAIN: 0.33x, 16x (Note 2) | 7 | |
| Integral Nonlinearity | INL | -10 | 10 | ppm FSR | GAIN = 0.33x (Note 2) | 8 | |
| Integral Nonlinearity | INL | -7 | 7 | ppm FSR | GAIN = 1x (Note 2) | 8 | |
| Integral Nonlinearity | INL | -20 | 20 | ppm FSR | GAIN = 8x (Note 2) | 8 | |
| Integral Nonlinearity | INL | -32 | 32 | ppm FSR | GAIN = 16x (Note 2) | 8 | |
| Signal-to-Noise and Distortion Ratio | SINAD | 105.8 | 106.7 | dB | AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) | 8 | |
| Signal-to-Noise Ratio | SNR | 106.7 | 107.2 | dBc | AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) | 8 | |
| Total Harmonic Distortion | THD | -116 | -111 | dB | AVDD = DVDD =VREF = 3.3V and TA = +25°C, includes the first 10 harmonics (Note 2) | 8 | |
| Spurious-Free Dynamic Range | SFDR | 110 | 120 | dBc | AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) | 8 | |
| External Master Clock Input Frequency Range | fMCLK_EXT | 1 | 20 | MHz | DVDD ≥ 2.7V | 9 | |
| External Master Clock Input Frequency Range | fMCLK_EXT | 1 | 10 | MHz | DVDD < 2.7V | 9 | |
| Master Clock Input Duty Cycle | fMCLK_DUTY | 45 | 55 | % | 9 | ||
| Internal Master Clock Frequency | fMCLK_INT | 3.3 | 6.6 | MHz | CLK_SEL[1] = 1 | 9 | |
| Internal Temperature Sensor Measurement Accuracy (printed ±5) | TAcc | -5 | 5 | °C | 9 | ||
| Data Transfer Time to DR (Data Ready) | tDODR | 50 | ns | 9 | |||
| Modulator Output Valid from AMCLK High | tDOMDAT | 100 | ns | 2.7V ≤ DVDD ≤ 3.6V | 9 | ||
| Modulator Output Valid from AMCLK High | tDOMDAT | 200 | ns | 1.8V ≤ DVDD ≤ 2.7V | 9 | ||
| SCAN Mode Time Delay Between Sampling Channels | TDLY_SCAN | 0 | 512 | DMCLK periods | 9 | ||
| Data Ready Pulse High Time | TDRH | 16 | DMCLK periods | See Figure 5-15 | 9 | ||
| Serial Clock Frequency (Table 1-1, DVDD = 2.7V to 3.6V) | fSCK | 20 | MHz | 10 | |||
| Data Setup Time (Table 1-1, DVDD = 2.7V to 3.6V) | tSU | 5 | ns | 10 | |||
| Data Hold Time (Table 1-1, DVDD = 2.7V to 3.6V) | tHD | 10 | ns | 10 | |||
| CS Setup Time (Table 1-1, DVDD = 2.7V to 3.6V) | tCSS | 25 | ns | 10 | |||
| CS Hold Time (Table 1-1, DVDD = 2.7V to 3.6V) | tCSH | 50 | ns | 10 | |||
| CS Disable Time (Table 1-1, DVDD = 2.7V to 3.6V) | tCSD | 50 | ns | 10 | |||
| Output Valid from SCK Low (Table 1-1, DVDD = 2.7V to 3.6V) | tDO | 25 | ns | 10 | |||
| Output Disable Time (Table 1-1, DVDD = 2.7V to 3.6V) | tDIS | 25 | ns | Measured with a 1.5 mA pull-up current source on SDO pin | 10 | ||
| POR IRQ Disable Time (Table 1-1, DVDD = 2.7V to 3.6V) | tCSIRQ | 52 | ns | Measured with a 1.5 mA pull-up current source on IRQ pin | 10 | ||
| Thermal Resistance, 20-Lead TSSOP | JA | 44 | °C/W | 10 |
CAD (KiCad official)
- Symbol:
MCP3561-E - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
mcp3561-e-etched.step/mcp3561-e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp3561-e.step/mcp3561-e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (108 pp, sha256
c8ad778bd923d8b9, retrieved 2026-10-24, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).