main
History Download
Ray Publish 0.1.0 66caab6

MCP3561-E

Microchip Tech · Analog To Digital Converters (ADCs) · TSSOP-20

MCP3561-E from Microchip Tech, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 AVDD power_in Analog supply pin, to be kept within the Electrical Characteristics range of 2.7 V to 3.6 V, with a 10 µF ceramic in parallel with a 0.1 µF ceramic recommended for bypass.
2 AGND power_in Analog ground, to be connected to the same ground as DGND (preferably star connection) and not internally connected to DGND.
3 REFIN- input Inverting differential reference input (VREF-); tie to AGND for single-ended reference use, and keep 0.6 V ≤ VREF ≤ AVDD.
4 REFIN+ input Noninverting differential reference input (VREF+); must satisfy 0.6 V ≤ VREF ≤ AVDD, with 0.1 µF and 10 µF bypass to AGND recommended.
5 CH0 input Analog input 0, selectable as VIN+ or VIN- by the multiplexer; pin voltage must stay between AGND - 0.1 V and VDD + 0.1 V.
6 CH1 input Analog input 1, selectable as VIN+ or VIN- by the multiplexer; pin voltage must stay between AGND - 0.1 V and VDD + 0.1 V.
7 NC unconnected Not connected for the MCP3561 (no internal function stated).
8 NC unconnected Not connected for the MCP3561 (no internal function stated).
9 NC unconnected Not connected for the MCP3561 (no internal function stated).
10 NC unconnected Not connected for the MCP3561 (no internal function stated).
11 NC unconnected Not connected for the MCP3561 (no internal function stated).
12 NC unconnected Not connected for the MCP3561 (no internal function stated).
13 CS input SPI chip select (Schmitt-triggered); communication starts on the falling edge and ends on the rising edge, and no communication occurs while high.
14 SCK input SPI serial clock input (Schmitt-triggered), maximum 20 MHz, with data latched in on the rising edge and clocked out on the falling edge.
15 SDI input SPI serial data input (Schmitt-triggered), latching data on the SCK rising edge; command byte is clocked in just after CS falls.
16 SDO tri_state SPI serial data output, clocked out on the SCK falling edge, and high-impedance when CS is high or during write/Fast command periods after the command byte.
17 IRQ/MDAT output Digital output configured by IRQ_MODE[1] as interrupt output (inactive state high-Z or logic high per IRQ_MODE[0]) or modulator data output; in high-Z mode an external pull-up of about 100-200 kΩ to DVDD is required.
18 MCLK bidirectional Master clock input for the ADC or analog master clock (AMCLK) output depending on CLK_SEL bits; typical frequency 4.9152 MHz and required continuously during conversions.
19 DGND power_in Digital ground for internal digital circuitry, to be connected to the same ground as AGND and not internally connected to AGND.
20 DVDD power_in Digital supply for internal digital circuitry, to be kept within the Electrical Characteristics range of 1.8 V to 3.6 V, with a 10 µF ceramic in parallel with a 0.1 µF ceramic recommended for bypass.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TSSOP-20
Category Data Converters
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
DVDD, AVDD supply voltage DVDD, AVDD -0.3 4 V 5
Digital inputs and outputs w.r.t. DGND -0.3 V 5
Analog inputs w.r.t. AGND -0.3 V 5
Current at input pins -5 5 mA 5
Current at output and supply pins -20 20 mA 5
Storage temperature -65 150 °C 5
Ambient temperature with power applied -65 125 °C 5
Maximum junction temperature (TJ) TJ 150 °C 5
ESD on all pins 6 kV HBM 5
Analog Operating Voltage AVDD 2.7 3.6 V 6
Digital Operating Voltage DVDD 1.8 V DVDD ≤ 3.6V 6
Operating Temperature Range TA -40 125 °C 10
Analog Operating Current AIDD 0.56 0.81 mA BOOST[1:0] = 00, 0.5x 6
Analog Operating Current AIDD 0.69 0.96 mA BOOST[1:0] = 01, 0.66x 6
Analog Operating Current AIDD 0.93 1.3 mA BOOST[1:0] = 10, 1x 6
Analog Operating Current AIDD 1.65 2.2 mA BOOST[1:0] = 11, 2x 6
Digital Operating Current DIDD 0.25 0.37 mA Note 8 6
Analog Partial Shutdown Current AIDDS_PS 22 µA 6
Digital Partial Shutdown Current DIDDS_PS 158 µA 6
Analog Full Shutdown Current AIDDS_FS 0.83 µA CONFIG0 = 0x00, TA = +105°C, MCLK input in Idle mode (Note 2) 6
Analog Full Shutdown Current AIDDS_FS 1.1 µA CONFIG0 = 0x00, TA = +125°C, MCLK input in Idle mode 6
Digital Full Shutdown Current DIDDS_FS 2.4 µA CONFIG0 = 0x00, TA = +105°C, MCLK input in Idle mode (Note 2) 6
Digital Full Shutdown Current DIDDS_FS 5 µA CONFIG0 = 0x00, TA = +125°C, MCLK input in Idle mode 6
Analog Input Leakage Current During ADC Shutdown ILI_A -10 10 nA 7
Reference Voltage Range (VREF+, VREF-) VREF 0.6 V 7
Resolution 24 Bits OSR ≥ 256 (Note 1) 7
Gain Error GE -3 3 % Note 6 7
Gain Error Temperature Coefficient GE_DRIFT 0.5 2 ppm/°C GAIN: 1x, 2x, 4x (Note 2) 7
Gain Error Temperature Coefficient GE_DRIFT 1 4 ppm/°C GAIN: 8x (Note 2) 7
Gain Error Temperature Coefficient GE_DRIFT 2 8 ppm/°C GAIN: 0.33x, 16x (Note 2) 7
Integral Nonlinearity INL -10 10 ppm FSR GAIN = 0.33x (Note 2) 8
Integral Nonlinearity INL -7 7 ppm FSR GAIN = 1x (Note 2) 8
Integral Nonlinearity INL -20 20 ppm FSR GAIN = 8x (Note 2) 8
Integral Nonlinearity INL -32 32 ppm FSR GAIN = 16x (Note 2) 8
Signal-to-Noise and Distortion Ratio SINAD 105.8 106.7 dB AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) 8
Signal-to-Noise Ratio SNR 106.7 107.2 dBc AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) 8
Total Harmonic Distortion THD -116 -111 dB AVDD = DVDD =VREF = 3.3V and TA = +25°C, includes the first 10 harmonics (Note 2) 8
Spurious-Free Dynamic Range SFDR 110 120 dBc AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) 8
External Master Clock Input Frequency Range fMCLK_EXT 1 20 MHz DVDD ≥ 2.7V 9
External Master Clock Input Frequency Range fMCLK_EXT 1 10 MHz DVDD < 2.7V 9
Master Clock Input Duty Cycle fMCLK_DUTY 45 55 % 9
Internal Master Clock Frequency fMCLK_INT 3.3 6.6 MHz CLK_SEL[1] = 1 9
Internal Temperature Sensor Measurement Accuracy (printed ±5) TAcc -5 5 °C 9
Data Transfer Time to DR (Data Ready) tDODR 50 ns 9
Modulator Output Valid from AMCLK High tDOMDAT 100 ns 2.7V ≤ DVDD ≤ 3.6V 9
Modulator Output Valid from AMCLK High tDOMDAT 200 ns 1.8V ≤ DVDD ≤ 2.7V 9
SCAN Mode Time Delay Between Sampling Channels TDLY_SCAN 0 512 DMCLK periods 9
Data Ready Pulse High Time TDRH 16 DMCLK periods See Figure 5-15 9
Serial Clock Frequency (Table 1-1, DVDD = 2.7V to 3.6V) fSCK 20 MHz 10
Data Setup Time (Table 1-1, DVDD = 2.7V to 3.6V) tSU 5 ns 10
Data Hold Time (Table 1-1, DVDD = 2.7V to 3.6V) tHD 10 ns 10
CS Setup Time (Table 1-1, DVDD = 2.7V to 3.6V) tCSS 25 ns 10
CS Hold Time (Table 1-1, DVDD = 2.7V to 3.6V) tCSH 50 ns 10
CS Disable Time (Table 1-1, DVDD = 2.7V to 3.6V) tCSD 50 ns 10
Output Valid from SCK Low (Table 1-1, DVDD = 2.7V to 3.6V) tDO 25 ns 10
Output Disable Time (Table 1-1, DVDD = 2.7V to 3.6V) tDIS 25 ns Measured with a 1.5 mA pull-up current source on SDO pin 10
POR IRQ Disable Time (Table 1-1, DVDD = 2.7V to 3.6V) tCSIRQ 52 ns Measured with a 1.5 mA pull-up current source on IRQ pin 10
Thermal Resistance, 20-Lead TSSOP JA 44 °C/W 10

CAD (KiCad official)

  • Symbol: MCP3561-E
  • Footprint: Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm
  • 3D model: TSSOP-20 (KiCad packages3D, STEP)
  • 3D model files: mcp3561-e-etched.step / mcp3561-e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp3561-e.step / mcp3561-e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (108 pp, sha256 c8ad778bd923d8b9, retrieved 2026-10-24, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF