Generated by kicad-footprint-generator · KiCad file format 20260206
MAX6966AEE+
Maxim Integrated · LED Drivers · QSOP-16-150mil
MAX6966AEE+ from Maxim Integrated, in a QSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCLK | input | Serial-clock input that shifts data into the shift register on its rising edge and clocks data out of DOUT on its falling edge, active only while CS is low. |
| 2 | CS | input | Chip-select input; serial data is loaded into the shift register while CS is low, and the most recent 16 bits latch on its rising edge. |
| 3 | P0 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 4 | P1 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 5 | P2 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 6 | P3 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 7 | P4 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 8 | GND | power_in | Ground; connect to the system ground and bypass V+ to it with a 0.1µF ceramic capacitor. |
| 9 | P5 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 10 | P6 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 11 | P7 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 12 | P8 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 13 | P9 | bidirectional | I/O port configurable as an open-drain current-sink output rated 20mA maximum, a CMOS logic input, or an open-drain logic output; loads must connect to a supply no higher than 7V. |
| 14 | DOUT/OSC | bidirectional | Serial-data output (push-pull) valid 15.5 clock cycles after DIN, or OSC square-wave CMOS clock input up to 100kHz; the MAX6966 powers up as DOUT and the MAX6967 powers up as OSC. |
| 15 | DIN | input | Serial-data input that loads into the internal 16-bit shift register on SCLK's rising edge. |
| 16 | V+ | power_in | Positive supply voltage for 2.25V to 3.6V operation; bypass to GND with a 0.1µF ceramic capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Maxim Integrated |
| Package | QSOP-16-150mil |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Supply Voltage | V+ | 2.25 | 3.6 | V | 2 | ||
| Output Load External Supply Voltage P0-P9 | VEXT | 7 | V | 2 | |||
| Standby Current (TA = +25°C) | ISTBY | 0.7 | 1.5 | µA | TA = +25°C; CS at V+; other digital inputs at V+ or GND; interface idle, CS run disabled, PWM disabled, all ports high impedance | 2 | |
| Standby Current (TA = TMIN to +85°C) | ISTBY | 1.7 | µA | TA = TMIN to +85°C; CS at V+; other digital inputs at V+ or GND | 2 | ||
| Standby Current (TA = TMIN to TMAX) | ISTBY | 1.9 | µA | TA = TMIN to TMAX; CS at V+; other digital inputs at V+ or GND | 2 | ||
| Supply Current Interface Only (TA = +25°C) | I+ | 390 | 620 | µA | TA = +25°C; fSCLK = 26MHz, other digital inputs at V+ or GND; DOUT unloaded | 2 | |
| Supply Current Interface Only (TA = TMIN to +85°C) | I+ | 680 | µA | TA = TMIN to +85°C; fSCLK = 26MHz, other digital inputs at V+ or GND; DOUT unloaded | 2 | ||
| Supply Current Interface Only (TA = TMIN to TMAX) | I+ | 730 | µA | TA = TMIN to TMAX; fSCLK = 26MHz, other digital inputs at V+ or GND; DOUT unloaded | 2 | ||
| Delta Supply Current per 10mA Port (TA = +25°C) | ΔI+10 | 1.58 | 1.8 | mA | TA = +25°C; interface idle, global current register 0x07, one port output register 0x02 with current bit cleared, others 0x00/0x01/0xFF; digital inputs at V+ or GND | 2 | |
| Delta Supply Current per 10mA Port (TA = TMIN to +85°C) | ΔI+10 | 1.9 | mA | TA = TMIN to +85°C; interface idle, global current register 0x07; digital inputs at V+ or GND | 2 | ||
| Delta Supply Current per 10mA Port (TA = TMIN to TMAX) | ΔI+10 | 2 | mA | TA = TMIN to TMAX; interface idle, global current register 0x07; digital inputs at V+ or GND | 2 | ||
| Delta Supply Current per 20mA Port (TA = +25°C) | ΔI+20 | 3.2 | 3.6 | mA | TA = +25°C; interface idle, global current register 0x07, one port output register 0x02 with current bit set, others 0x00/0x01/0xFF; digital inputs at V+ or GND | 2 | |
| Delta Supply Current per 20mA Port (TA = TMIN to +85°C) | ΔI+20 | 3.8 | mA | TA = TMIN to +85°C; interface idle, global current register 0x07; digital inputs at V+ or GND | 2 | ||
| Delta Supply Current per 20mA Port (TA = TMIN to TMAX) | ΔI+20 | 4 | mA | TA = TMIN to TMAX; interface idle, global current register 0x07; digital inputs at V+ or GND | 2 | ||
| Input High Voltage (P0-P9, DIN, SCLK, CS, OSC) | VIH | 0.7 | x V+ | P0-P9: output register set to 0x01 | 3 | ||
| Input Low Voltage (P0-P9, DIN, SCLK, CS, OSC) | VIL | 0.3 | x V+ | P0-P9: output register set to 0x01 | 3 | ||
| Input Leakage Current (P0-P9, DIN, SCLK, CS, OSC) | IIH, IIL | -0.2 | 0.2 | µA | 3 | ||
| Port Nominal Sink Constant Current (TA = +25°C, 20mA range) | IOUT | 19.3 | 20 | 21.1 | mA | TA = +25°C; global current register 0x07; output register set to 0x02; V+ = 3.3V; VEXT - VLED = 1V to 2.5V | 3 |
| Port Nominal Sink Constant Current (TA = +25°C, 10mA range) | IOUT | 9.5 | 10 | 10.7 | mA | TA = +25°C; global current register 0x07; output register set to 0x02; V+ = 3.3V; VEXT - VLED = 1V to 2.5V | 3 |
| Port Nominal Sink Constant Current (TA = TMIN to +85°C, 20mA range) | IOUT | 18.8 | 21.8 | mA | TA = TMIN to +85°C; global current register 0x07; output register set to 0x02; V+ = 3.3V; VEXT - VLED = 1V to 2.5V | 3 | |
| Port Nominal Sink Constant Current (TA = TMIN to +85°C, 10mA range) | IOUT | 9.1 | 11 | mA | TA = TMIN to +85°C; global current register 0x07; output register set to 0x02; V+ = 3.3V; VEXT - VLED = 1V to 2.5V | 3 | |
| Port Logic Output Low Voltage | VOLP_ | 0.4 | V | Output register set to 0x00, ISINK = 0.5mA | 3 | ||
| Port Logic Output Low Short-Circuit Current | 10.8 | 20 | mA | Output register set to 0x00, VOLP_ = 5V | 3 | ||
| Port Slew Time | 2 | µs | From 20% current to 80% current | 3 | |||
| Port Sink Constant-Current Matching (20mA) | ΔIOUT | -4 | 4 | % | TA = +25°C, V+ = 3.3V, VEXT - VLED = 1.4V, IOUT = 20mA | 3 | |
| Port Sink Constant-Current Matching (10mA) | ΔIOUT | -5 | 5 | % | TA = +25°C, V+ = 3.3V, VEXT - VLED = 1.4V, IOUT = 10mA | 3 | |
| Output Low Voltage (DOUT) | VOLDOUT | 0.3 | V | ISINK = 6mA | 3 | ||
| Internal PWM Clock Frequency | fINT | 27000 | 45000 | Hz | 4 | ||
| External PWM Clock Frequency | fOSC | 100 | kHz | 4 | |||
| SCLK Clock Period | tCP | 38.4 | ns | 4 | |||
| SCLK Pulse Width High | tCH | 19 | ns | 4 | |||
| SCLK Pulse Width Low | tCL | 19 | ns | 4 | |||
| CS Fall to SCLK Rise Setup Time | tCSS | 9.5 | ns | 4 | |||
| SCLK Rise to CS Rise Hold Time | tCSH | 0 | ns | 4 | |||
| DIN Setup Time | tDS | 9.5 | ns | 4 | |||
| DIN Hold Time | tDH | 0 | ns | 4 | |||
| Output Data Propagation Delay | tDO | 21 | ns | 4 | |||
| DOUT Output Rise and Fall Times | tFT | 10 | ns | CLOAD = 20pF | 4 | ||
| Minimum CS Pulse High | tCSW | 38.4 | ns | 4 | |||
| CS Pulse Low to Not Activate CS Run | tCSRUN | 640 | µs | CS run enabled | 4 | ||
| CS Pulse Width to Activate CS Run | tCSRUN | 3 | ms | CS run enabled | 4 | ||
| Supply Voltage (absolute maximum) | V+ | -0.3 | 4 | V | Voltage with respect to GND | 2 | |
| Logic Input/Output Voltage SCLK, DIN, CS, DOUT/OSC | -0.3 | V | Upper limit V+ + 0.3V | 2 | |||
| Port Voltage P_ | P_ | -0.3 | 8 | V | Voltage with respect to GND | 2 | |
| DC Current into DOUT/OSC | 10 | mA | 2 | ||||
| Operating Temperature Range | TA | -40 | 125 | °C | TMIN to TMAX | 2 | |
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Lead Temperature | 300 | °C | Soldering, 10s | 2 |
CAD (KiCad official)
- Symbol:
MAX6966AEE+ - Footprint:
Package_SO:QSOP-16_3.9x4.9mm_P0.635mm - 3D model: QSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
max6966aee-etched.step/max6966aee-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max6966aee.step/max6966aee.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Maxim Integrated datasheet (28 pp, sha256
8d195ff40537777f, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).