Generated by kicad-footprint-generator · KiCad file format 20260206
MAX32664GTGC+
MAXIM INTEGRATED · Global Sourcing Parts · TQFN-24-EP(3x3)
MAX32664GTGC+ from MAXIM INTEGRATED, in a TQFN-24-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MFIO | bidirectional | Multifunction I/O that the host asserts low to communicate with the sensor hub, and when held low during reset it enters bootloader mode. |
| 2 | D.N.C. | unconnected | Internally connected; do not make any electrical connection, including VSS, to this pin. |
| 3 | NC | unconnected | Not connected to the die and can be used to route any signal. |
| 4 | D.N.C. | unconnected | Internally connected; do not make any electrical connection, including VSS, to this pin. |
| 5 | D.N.C. | unconnected | Internally connected; do not make any electrical connection, including VSS, to this pin. |
| 6 | RSTN | input | External active-low system reset input with an internal pullup to VDD; a noise snubber circuit should be placed as close to the device as possible. |
| 7 | VSS | power_in | Digital ground for the device. |
| 8 | 32KOUT | output | 32.768kHz crystal oscillator output for RTC operation; leave unconnected if an external clock drives 32KIN. |
| 9 | 32KIN | input | 32.768kHz crystal oscillator input; a crystal connects between 32KIN and 32KOUT, or an external clock can be driven on 32KIN when 32KOUT is unconnected. |
| 10 | VSS | power_in | Digital ground for the device. |
| 11 | VDD | power_in | Digital supply voltage; bypass to VSS with a 1.0μF capacitor as close as possible to the package. |
| 12 | VCORE | power_out | Core supply voltage; bypass to VSS with a 1.0μF capacitor as close as possible to the package and do not connect to any other circuit. |
| 13 | SENSOR_SDA | bidirectional | I2C master data line that connects to the SDA of the slave sensors; pullup resistors are required. |
| 14 | SENSOR_SCL | bidirectional | I2C master clock line that connects to the SCL of the slave sensors; pullup resistors are required. |
| 15 | NC | unconnected | Not connected to the die and can be used to route any signal. |
| 16 | D.N.C. | unconnected | Internally connected; do not make any electrical connection, including VSS, to this pin. |
| 17 | D.N.C. | unconnected | Internally connected; do not make any electrical connection, including VSS, to this pin. |
| 18 | HR_INT | input | Input connected to the heart rate/PPG monitor sensor interrupt output. |
| 19 | ACCEL_INT | input | Input connected to the accelerometer sensor interrupt output. |
| 20 | LDO_EN | output | LDO enable output connected to the heart rate/PPG monitor sensor LDO enable pin. |
| 21 | GPIO | bidirectional | General-purpose input/output that is open drain when programmed as an output (active low) and connects to the heart rate/PPG monitor sensor GPIO pin. |
| 22 | VDD | power_in | Digital supply voltage; bypass to VSS with a 1.0μF capacitor as close as possible to the package. |
| 23 | SLAVE_SDA | bidirectional | I2C slave data line that connects to the host I2C master SDA. |
| 24 | SLAVE_SCL | input | I2C slave clock input that connects to the host I2C master SCL. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MAXIM INTEGRATED |
| Package | TQFN-24-EP(3x3) |
| Category | Global Sourcing Parts |
| Pins | 25 |
CAD (KiCad official)
- Symbol:
MAX32664GTGC+ - Footprint:
Package_DFN_QFN:QFN-24-1EP_3x3mm_P0.4mm_EP1.75x1.6mm - 3D model: TQFN-24-EP(3x3), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
max32664gtgc-etched.step/max32664gtgc-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max32664gtgc.step/max32664gtgc.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MAXIM INTEGRATED datasheet (33 pp, sha256
8b84ad33ec5681dc, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).