Generated by kicad-footprint-generator · KiCad file format 20260206
LTC1563-2CGN#PBF
Analog Devices · Pre-ordered Chips · SSOP-16-150mil
LTC1563-2CGN#PBF from Analog Devices, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LP | input | Low Power mode select: a logic high or open pin selects High Speed mode (a small pull-up defaults the part to High Speed if left open), and a logic low or connection to V- selects Low Power mode. |
| 2 | SA | passive | Section A summing point for signals fed forward and backward; capacitance on this pin causes peaking near cutoff, so the section A resistors should be placed as close as possible to it. |
| 3 | NC | unconnected | Not connected internally; for best performance it should be connected to ground. |
| 4 | INVA | input | Inverting input of the section A op amp; it is a high-impedance, noise-sensitive node, so its printed circuit connection must be kept as short as possible. |
| 5 | NC | unconnected | Not connected internally; for best performance it should be connected to ground. |
| 6 | LPA | output | Section A lowpass output from a rail-to-rail op amp, designed to drive a nominal net load of 5kΩ and 20pF. |
| 7 | AGND | power_in | Analog ground, the midpoint of an internal resistive divider between V+ and V- with a nominal series equivalent resistance of 10kΩ, serving as the internal ground reference; the analog ground plane should connect to digital ground at a single point. |
| 8 | V- | power_in | Negative supply pin, to be bypassed with a 0.1µF capacitor as close to the pin as possible; total supply voltage (V+ to V-) must not exceed 11V. |
| 9 | EN | input | Enable: a logic high or open pin puts the part in shutdown (outputs and AGND high impedance), and it must be connected to V- or a logic low to enable normal operation. |
| 10 | NC | unconnected | Not connected internally; for best performance it should be connected to ground. |
| 11 | SB | passive | Section B summing point for signals fed forward and backward; capacitance on this pin causes peaking near cutoff, so the section B resistors should be placed as close as possible to it. |
| 12 | NC | unconnected | Not connected internally; for best performance it should be connected to ground. |
| 13 | INVB | input | Inverting input of the section B op amp; it is a high-impedance, noise-sensitive node, so its printed circuit connection must be kept as short as possible. |
| 14 | NC | unconnected | Not connected internally; for best performance it should be connected to ground. |
| 15 | LPB | output | Section B lowpass output from a rail-to-rail op amp, designed to drive a nominal net load of 5kΩ and 20pF. |
| 16 | V+ | power_in | Positive supply pin, to be bypassed with a 0.1µF capacitor as close to the pin as possible; total supply voltage (V+ to V-) must not exceed 11V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SSOP-16-150mil |
| Category | Interface ICs |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Total Supply Voltage (V+ to V-) | 11 | V | 2 | ||||
| Operating Temperature Range (LTC1563C) | 0 | 70 | °C | LTC1563C | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Power Dissipation | 500 | mW | 2 | ||||
| Total Supply Voltage (VS), HS Mode | 3 | 11 | V | 2 | |||
| Total Supply Voltage (VS), LP Mode | 2.7 | 11 | V | 2 | |||
| Output Voltage Swing High (LPB Pin) | 2.9 | 2.95 | V | HS Mode; VS = 3V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Voltage Swing High (LPB Pin) | 4.55 | 4.7 | V | HS Mode; VS = 4.75V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Voltage Swing High (LPB Pin) | 4.8 | 4.9 | V | HS Mode; VS = ±5V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Voltage Swing Low (LPB Pin) | 0.015 | 0.05 | V | HS Mode; VS = 3V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Voltage Swing Low (LPB Pin) | 0.02 | 0.05 | V | HS Mode; VS = 4.75V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Voltage Swing Low (LPB Pin) | -4.95 | -4.9 | V | HS Mode; VS = ±5V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Swing High (LPB Pin) | 2.6 | 2.65 | V | LP Mode; VS = 2.7V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Swing High (LPB Pin) | 4.55 | 4.65 | V | LP Mode; VS = 4.75V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Swing High (LPB Pin) | 4.8 | 4.9 | V | LP Mode; VS = ±5V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Swing Low (LPB Pin) | 0.01 | 0.05 | V | LP Mode; VS = 2.7V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Swing Low (LPB Pin) | 0.015 | 0.05 | V | LP Mode; VS = 4.75V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| Output Swing Low (LPB Pin) | -4.95 | -4.9 | V | LP Mode; VS = ±5V, fC = 25.6kHz, RFIL = 100k, RL = 10k to GND | 2 | ||
| DC Offset Voltage, HS Mode (Section A Only) | -3 | 1.5 | 3 | mV | VS = 3V, fC = 25.6kHz, RFIL = 100k | 2 | |
| DC Offset Voltage, HS Mode (Section A Only) | -3 | 1 | 3 | mV | VS = 4.75V, fC = 25.6kHz, RFIL = 100k | 2 | |
| DC Offset Voltage, LP Mode (Section A Only) | -6 | 2 | 6 | mV | VS = 2.7V, fC = 25.6kHz, RFIL = 100k | 2 | |
| DC Offset Voltage, LP Mode (Section A Only) | -7 | 2 | 7 | mV | VS = ±5V, fC = 25.6kHz, RFIL = 100k | 2 | |
| DC Offset Voltage, HS Mode (Input to Output, Sections A, B Cascaded) | -3 | 1.5 | 3 | mV | VS = 3V, fC = 25.6kHz, RFIL = 100k | 2 | |
| DC Offset Voltage, HS Mode (Input to Output, Sections A, B Cascaded) | -3 | 1 | 3 | mV | VS = 4.75V, fC = 25.6kHz, RFIL = 100k | 2 | |
| DC Offset Voltage, LP Mode (Input to Output, Sections A, B Cascaded) | -7 | 2 | 7 | mV | VS = 2.7V, fC = 25.6kHz, RFIL = 100k | 3 | |
| DC Offset Voltage, LP Mode (Input to Output, Sections A, B Cascaded) | -8 | 2 | 8 | mV | VS = ±5V, fC = 25.6kHz, RFIL = 100k | 3 | |
| Power Supply Current, HS Mode | 8 | 14 | mA | VS = 3V, fC = 25.6kHz, RFIL = 100k | 3 | ||
| Power Supply Current, HS Mode | 10.5 | 17 | mA | VS = 4.75V, fC = 25.6kHz, RFIL = 100k | 3 | ||
| Power Supply Current, HS Mode | 15 | 23 | mA | VS = ±5V, fC = 25.6kHz, RFIL = 100k | 3 | ||
| Power Supply Current, LP Mode | 1 | 1.8 | mA | VS = 2.7V, fC = 25.6kHz, RFIL = 100k | 3 | ||
| Power Supply Current, LP Mode | 1.4 | 2.5 | mA | VS = 4.75V, fC = 25.6kHz, RFIL = 100k | 3 | ||
| Power Supply Current, LP Mode | 2.3 | 3.5 | mA | VS = ±5V, fC = 25.6kHz, RFIL = 100k | 3 | ||
| Shutdown Mode Supply Current | 1 | 20 | µA | VS = 4.75V, fC = 25.6kHz, RFIL = 100k | 3 | ||
| AGND Voltage | 2.35 | 2.375 | 2.4 | V | VS = 4.75V, fC = 25.6kHz, RFIL = 100k | 3 | |
| EN Input Logic Low Level | 0.8 | V | VS = 3V | 3 | |||
| EN Input Logic Low Level | 1 | V | VS = 4.75V | 3 | |||
| EN Input Logic High Level | 2.5 | V | VS = 3V | 3 | |||
| EN Input Logic High Level | 4.3 | V | VS = 4.75V | 3 | |||
| EN Input Logic High Level | 4.4 | V | VS = ±5V | 3 | |||
| LP Logic Low Level | 0.8 | V | VS = 3V | 3 | |||
| LP Logic Low Level | 1 | V | VS = 4.75V | 3 | |||
| LP Logic High Level | 2.5 | V | VS = 3V | 3 | |||
| LP Logic High Level | 4.3 | V | VS = 4.75V | 3 | |||
| LP Logic High Level | 4.4 | V | VS = ±5V | 3 | |||
| Cutoff Frequency Accuracy, HS Mode (fC = 25.6kHz) | -2 | 1.5 | 3.5 | % | VS = 3V, RFIL = 100k | 3 | |
| Cutoff Frequency Accuracy, HS Mode (fC = 256kHz) | -5 | 1.5 | 2.5 | % | VS = 3V, RFIL = 10k | 3 | |
| Cutoff Frequency Accuracy, LP Mode (fC = 25.6kHz) | -3 | 1.5 | 3 | % | VS = 2.7V, RFIL = 100k | 3 | |
| Thermal Resistance, Junction to Ambient (GN Package) | θJA | 135 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LTC1563-2CGN#PBF - Footprint:
Package_SO:SSOP-16_3.9x4.9mm_P0.635mm - 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
ltc1563-2cgn-etched.step/ltc1563-2cgn-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc1563-2cgn.step/ltc1563-2cgn.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
8acdc1ffd2c413d5, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).