Generated by kicad-footprint-generator · KiCad file format 20260206
LT3988EMSE#PBF
Analog Devices · DC-DC Converters · MSOP-16-EP
LT3988EMSE#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DA1 | passive | Connects to the anode of the channel 1 external Schottky catch diode; switching is disabled if the DA pin current exceeds 1.32A until it falls below 1.32A. |
| 2 | SW1 | output | Output of the channel 1 internal power switch, connected to the inductor, catch diode and boost capacitor. |
| 3 | BOOST1 | passive | Provides a drive voltage higher than the input voltage to the channel 1 internal NPN power switch. |
| 4 | BD | power_in | Internal boost diodes connect between BD and the BOOST pins; connect BD to a 3V or higher supply such as VOUT (20V absolute maximum). |
| 5 | EN/UVLO | input | Shuts down the LT3988; can be driven from logic, tied to the input, or used as undervoltage lockout via a resistor divider from VIN1 (1.2V typ rising threshold, 80V absolute maximum). |
| 6 | BOOST2 | passive | Provides a drive voltage higher than the input voltage to the channel 2 internal NPN power switch. |
| 7 | SW2 | output | Output of the channel 2 internal power switch, connected to the inductor, catch diode and boost capacitor. |
| 8 | DA2 | passive | Connects to the anode of the channel 2 external Schottky catch diode; switching is disabled if the DA pin current exceeds 1.32A until it falls below 1.32A. |
| 9 | VIN2 | power_in | Supplies current to the channel 2 internal power switch and must be locally bypassed; connect to VIN1 unless channel 2 has a separate source, must exceed 2.6V (typ), and must be tied to VIN1 if driven above 60V. |
| 10 | TRACK/SS2 | passive | Soft-start or tracking input for channel 2: tie a capacitor for soft-start (internal -1.2µA charging current) or a resistor divider from the tracked output; leave disconnected if unused. |
| 11 | FB2 | input | Channel 2 feedback pin regulated to 0.750V; connect the feedback resistor divider tap here. |
| 12 | SYNC | input | Synchronizes the oscillator to an external logic-level clock with positive and negative pulse widths of at least 100ns (0.25 to 2.5MHz); connect to ground if unused. |
| 13 | RT | passive | Sets the internal oscillator frequency with a resistor from RT to GND (250kHz to 2.5MHz). |
| 14 | FB1 | input | Channel 1 feedback pin regulated to 0.750V; connect the feedback resistor divider tap here. |
| 15 | TRACK/SS1 | passive | Soft-start or tracking input for channel 1: tie a capacitor for soft-start (internal -1.2µA charging current) or a resistor divider from the tracked output; leave disconnected if unused. |
| 16 | VIN1 | power_in | Supplies the internal circuitry and the channel 1 power switch and must be locally bypassed; must exceed 3.9V (typ) for either channel to operate. |
| 17 | GND | power_in | Exposed pad providing electrical ground and thermal contact to the PCB; must be soldered to the board for proper operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN1 Undervoltage Lockout | 3.9 | 4.1 | V | VIN1 Rising | 2 | ||
| VIN1 Overvoltage Lockout | 60 | 64 | 66 | V | VIN1 Rising | 2 | |
| VIN2 Undervoltage Lockout | 2 | 2.6 | 3.1 | V | VIN2 Rising, VIN1 = 4.1V | 2 | |
| EN/UVLO Input Current | -0.5 | 0.5 | µA | VEN/UVLO = 1.2V | 2 | ||
| EN/UVLO Undervoltage Threshold | 1.1 | 1.2 | 1.3 | V | VEN/UVLO = Rising | 2 | |
| EN/UVLO Enable Threshold | 300 | 500 | mV | 2 | |||
| VIN1 Quiescent Current | 2.7 | 4.5 | mA | VFB1 = 0.9V, VBD = 0V | 3 | ||
| VIN1 Quiescent Current | 1.6 | 3 | mA | VFB1 = 0.9V, VBD = 5V | 3 | ||
| VIN2 Quiescent Current | 250 | 1000 | µA | VFB2 = 0.9V, VBD = 5V | 3 | ||
| BD Pin Current | -8 | -30 | µA | VBD = 0V | 3 | ||
| BD Pin Quiescent Current | 1.1 | 2.2 | mA | VBD = 5V | 3 | ||
| Shutdown Current (IVIN1+IVIN2) | 0.1 | 1 | µA | VEN/UVLO ≤ 0.3V | 3 | ||
| FB Voltage | 0.74 | 0.75 | 0.76 | V | 3 | ||
| FB Voltage (full temperature range) | 0.735 | 0.75 | 0.765 | V | over full operating temperature range | 3 | |
| FB Pin Bias Current | -5 | -100 | nA | VFB = 0.75V | 3 | ||
| Switching Frequency | 0.9 | 1 | 1.1 | MHz | RT = 40.2k | 3 | |
| Switching Phase, SW1 to SW2 | 150 | 180 | 210 | Deg | RT = 40.2k | 3 | |
| DA Comparator Current Threshold | 1.1 | 1.32 | 1.58 | A | 3 | ||
| Switch Current Limit | 1.4 | 1.87 | 2.25 | A | Duty Cycle = 35% | 3 | |
| Switch Leakage Current | 0.01 | 1 | µA | 3 | |||
| Minimum Boost Voltage | 2 | 2.5 | V | 3 | |||
| Boost Pin Current | 20 | 50 | mA | ISW = 1A | 3 | ||
| Boost Diode Forward Voltage | 0.7 | 0.9 | V | IBD = 50mA | 3 | ||
| Boost Diode Leakage Current | 0.1 | 5 | µA | VR = 5V | 3 | ||
| TRACK/SS Pin Current | -0.8 | -1.3 | -2.2 | µA | VTRACK/SS = 1V | 3 | |
| SYNC Input High Voltage | VIH | 1.5 | V | 3 | |||
| SYNC Input Low Voltage | VIL | 0.4 | V | 3 | |||
| SYNC Input Frequency | 0.25 | 2.5 | MHz | 3 | |||
| SYNC Pin Input Current | 0.3 | µA | VSYNC = 1.5V | 3 | |||
| VIN1 Undervoltage Lockout Hysteresis | 260 | mV | 2 | ||||
| VIN1 Overvoltage Lockout Hysteresis | 2.1 | V | 2 | ||||
| VIN2 Undervoltage Lockout Hysteresis | 135 | mV | 2 | ||||
| EN/UVLO Undervoltage Threshold Hysteresis | 120 | mV | 2 | ||||
| Switch VSAT | 850 | mV | ISW = 1A | 3 | |||
| Switching Frequency | 250 | kHz | RT = 200k | 3 | |||
| Switching Frequency | 2.15 | MHz | RT = 14.7k | 3 | |||
| FB Line Voltage Regulation | 0.01 | %/V | 5V < VIN < 60V | 3 | |||
| VIN Absolute Maximum | VIN | -0.3 | 80 | V | Notes 7, 8 | 2 | |
| BOOST Absolute Maximum | BOOST | 80 | V | 2 | |||
| EN/UVLO Absolute Maximum | EN/UVLO | 80 | V | Note 7 | 2 | ||
| BOOST above SW | 30 | V | 2 | ||||
| EN/UVLO above VIN1 | 6 | V | 2 | ||||
| RT, SYNC Absolute Maximum | 6 | V | 2 | ||||
| TRACK/SS, FB Absolute Maximum | 5 | V | 2 | ||||
| BD Absolute Maximum | BD | 20 | V | 2 | |||
| Operating Junction Temperature Range (LT3988E) | -40 | 125 | °C | Note 2 | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering, 10 sec) | 300 | °C | 2 | ||||
| Thermal Resistance Junction-to-Ambient | θJA | 40 | °C/W | 16-lead MSOP (MSE) | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 10 | °C/W | 16-lead MSOP (MSE) | 2 |
CAD (KiCad official)
- Symbol:
LT3988EMSE#PBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt3988emse-pbf-etched.step/lt3988emse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3988emse-pbf.step/lt3988emse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
0d50e10a117d9cb6, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).