main
Ray Publish 0.1.0 7d1552f

LT3988EMSE#PBF

Analog Devices · DC-DC Converters · MSOP-16-EP

LT3988EMSE#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DA1 passive Connects to the anode of the channel 1 external Schottky catch diode; switching is disabled if the DA pin current exceeds 1.32A until it falls below 1.32A.
2 SW1 output Output of the channel 1 internal power switch, connected to the inductor, catch diode and boost capacitor.
3 BOOST1 passive Provides a drive voltage higher than the input voltage to the channel 1 internal NPN power switch.
4 BD power_in Internal boost diodes connect between BD and the BOOST pins; connect BD to a 3V or higher supply such as VOUT (20V absolute maximum).
5 EN/UVLO input Shuts down the LT3988; can be driven from logic, tied to the input, or used as undervoltage lockout via a resistor divider from VIN1 (1.2V typ rising threshold, 80V absolute maximum).
6 BOOST2 passive Provides a drive voltage higher than the input voltage to the channel 2 internal NPN power switch.
7 SW2 output Output of the channel 2 internal power switch, connected to the inductor, catch diode and boost capacitor.
8 DA2 passive Connects to the anode of the channel 2 external Schottky catch diode; switching is disabled if the DA pin current exceeds 1.32A until it falls below 1.32A.
9 VIN2 power_in Supplies current to the channel 2 internal power switch and must be locally bypassed; connect to VIN1 unless channel 2 has a separate source, must exceed 2.6V (typ), and must be tied to VIN1 if driven above 60V.
10 TRACK/SS2 passive Soft-start or tracking input for channel 2: tie a capacitor for soft-start (internal -1.2µA charging current) or a resistor divider from the tracked output; leave disconnected if unused.
11 FB2 input Channel 2 feedback pin regulated to 0.750V; connect the feedback resistor divider tap here.
12 SYNC input Synchronizes the oscillator to an external logic-level clock with positive and negative pulse widths of at least 100ns (0.25 to 2.5MHz); connect to ground if unused.
13 RT passive Sets the internal oscillator frequency with a resistor from RT to GND (250kHz to 2.5MHz).
14 FB1 input Channel 1 feedback pin regulated to 0.750V; connect the feedback resistor divider tap here.
15 TRACK/SS1 passive Soft-start or tracking input for channel 1: tie a capacitor for soft-start (internal -1.2µA charging current) or a resistor divider from the tracked output; leave disconnected if unused.
16 VIN1 power_in Supplies the internal circuitry and the channel 1 power switch and must be locally bypassed; must exceed 3.9V (typ) for either channel to operate.
17 GND power_in Exposed pad providing electrical ground and thermal contact to the PCB; must be soldered to the board for proper operation.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN1 Undervoltage Lockout 3.9 4.1 V VIN1 Rising 2
VIN1 Overvoltage Lockout 60 64 66 V VIN1 Rising 2
VIN2 Undervoltage Lockout 2 2.6 3.1 V VIN2 Rising, VIN1 = 4.1V 2
EN/UVLO Input Current -0.5 0.5 µA VEN/UVLO = 1.2V 2
EN/UVLO Undervoltage Threshold 1.1 1.2 1.3 V VEN/UVLO = Rising 2
EN/UVLO Enable Threshold 300 500 mV 2
VIN1 Quiescent Current 2.7 4.5 mA VFB1 = 0.9V, VBD = 0V 3
VIN1 Quiescent Current 1.6 3 mA VFB1 = 0.9V, VBD = 5V 3
VIN2 Quiescent Current 250 1000 µA VFB2 = 0.9V, VBD = 5V 3
BD Pin Current -8 -30 µA VBD = 0V 3
BD Pin Quiescent Current 1.1 2.2 mA VBD = 5V 3
Shutdown Current (IVIN1+IVIN2) 0.1 1 µA VEN/UVLO ≤ 0.3V 3
FB Voltage 0.74 0.75 0.76 V 3
FB Voltage (full temperature range) 0.735 0.75 0.765 V over full operating temperature range 3
FB Pin Bias Current -5 -100 nA VFB = 0.75V 3
Switching Frequency 0.9 1 1.1 MHz RT = 40.2k 3
Switching Phase, SW1 to SW2 150 180 210 Deg RT = 40.2k 3
DA Comparator Current Threshold 1.1 1.32 1.58 A 3
Switch Current Limit 1.4 1.87 2.25 A Duty Cycle = 35% 3
Switch Leakage Current 0.01 1 µA 3
Minimum Boost Voltage 2 2.5 V 3
Boost Pin Current 20 50 mA ISW = 1A 3
Boost Diode Forward Voltage 0.7 0.9 V IBD = 50mA 3
Boost Diode Leakage Current 0.1 5 µA VR = 5V 3
TRACK/SS Pin Current -0.8 -1.3 -2.2 µA VTRACK/SS = 1V 3
SYNC Input High Voltage VIH 1.5 V 3
SYNC Input Low Voltage VIL 0.4 V 3
SYNC Input Frequency 0.25 2.5 MHz 3
SYNC Pin Input Current 0.3 µA VSYNC = 1.5V 3
VIN1 Undervoltage Lockout Hysteresis 260 mV 2
VIN1 Overvoltage Lockout Hysteresis 2.1 V 2
VIN2 Undervoltage Lockout Hysteresis 135 mV 2
EN/UVLO Undervoltage Threshold Hysteresis 120 mV 2
Switch VSAT 850 mV ISW = 1A 3
Switching Frequency 250 kHz RT = 200k 3
Switching Frequency 2.15 MHz RT = 14.7k 3
FB Line Voltage Regulation 0.01 %/V 5V < VIN < 60V 3
VIN Absolute Maximum VIN -0.3 80 V Notes 7, 8 2
BOOST Absolute Maximum BOOST 80 V 2
EN/UVLO Absolute Maximum EN/UVLO 80 V Note 7 2
BOOST above SW 30 V 2
EN/UVLO above VIN1 6 V 2
RT, SYNC Absolute Maximum 6 V 2
TRACK/SS, FB Absolute Maximum 5 V 2
BD Absolute Maximum BD 20 V 2
Operating Junction Temperature Range (LT3988E) -40 125 °C Note 2 2
Storage Temperature Range -65 150 °C 2
Lead Temperature (Soldering, 10 sec) 300 °C 2
Thermal Resistance Junction-to-Ambient θJA 40 °C/W 16-lead MSOP (MSE) 2
Thermal Resistance Junction-to-Case θJC 10 °C/W 16-lead MSOP (MSE) 2

CAD (KiCad official)

  • Symbol: LT3988EMSE#PBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt3988emse-pbf-etched.step / lt3988emse-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3988emse-pbf.step / lt3988emse-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (24 pp, sha256 0d50e10a117d9cb6, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF