main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lt3761emse-pbf: viewers · Ray
lt3761emse-pbf-etched.glb Publish 0.1.0 · Ray
lt3761emse-pbf-etched.step lt3761emse-pbf: factory component page (tier=mfr) · Ray
lt3761emse-pbf-hero.glb lt3761emse-pbf: hero GLB from the etched model (keeps the MPN mark) · Ray
lt3761emse-pbf-hero.overlay.json Publish 0.1.0 · Ray
lt3761emse-pbf.glb Publish 0.1.0 · Ray
lt3761emse-pbf.kicad_mod Publish 0.1.0 · Ray
lt3761emse-pbf.kicad_sym Publish 0.1.0 · Ray
lt3761emse-pbf.lbr Publish 0.1.0 · Ray
lt3761emse-pbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

LT3761EMSE#PBF

Analog Devices · LED Drivers · MSOP-16-EP

LT3761EMSE#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PWMOUT output Buffered PWM signal driven from INTVCC for an LED load disconnect NMOS or level shift, toggling if FB exceeds VFB plus 60mV (typical).
2 FB input Voltage loop feedback regulated to 1.25V (nominal) that must not be left open and must be connected to GND if unused, with FB overvoltage threshold of VFB plus 60mV (typical).
3 ISN input Negative terminal connection of the current feedback resistor, with input bias current typically 20µA flowing into the pin when ISN is greater than INTVCC.
4 ISP input Positive terminal connection of the current feedback resistor, where an ISP-ISN difference above 600mV (typical) triggers an overcurrent event that drives GATE and PWMOUT low.
5 VC passive Transconductance error amplifier output that requires a capacitor to GND with a series resistor recommended for fast transient response, and is high impedance when PWM is low.
6 CTRL input Current sense threshold adjustment input that must not be left open, with VISP-ISN reaching the full-scale 250mV for CTRL above 1.2V.
7 VREF power_in Voltage reference output, typically 2V, that can supply up to 185µA (typical) to a resistor divider for the CTRL pin.
8 PWM input PWM input where a signal low turns off the switcher, and which must be connected to INTVCC if not used, with a capacitor to GND invoking a self-driving oscillator.
9 OPENLED output Open-drain pull-down output (LT3761 only) that asserts when FB is above VFB minus 50mV (typical) and ISP-ISN is below 25mV, and requires an external pull-up, usually to INTVCC.
10 DIM/SS passive Soft-start and PWMOUT dimming signal generator programming pin with a 12µA (typical) internal pull-up and a capacitor to GND of minimum 560pF when the PWMOUT generator is used.
11 RT passive Switching frequency adjustment pin set by a resistor to GND, which must not be left open and should be placed close to the IC.
12 EN/UVLO input Enable and undervoltage detect pin with a 1.22V falling threshold and 1.24V (typical) rising enable threshold, which must be tied to 0.4V or less to disable the device.
13 INTVCC power_out Current limited low dropout linear regulator output regulating to 7.85V (typical) from VIN, which must be bypassed with a 1µF ceramic capacitor placed close to the pin and exposed pad GND.
14 VIN power_in Power supply input for internal loads and the INTVCC regulator, which must be locally bypassed with a 0.22µF (or larger) low ESR capacitor placed close to the pin.
15 SENSE input Current sense input for the switch control loop that must be Kelvin connected to the positive terminal of the switch current sense resistor in the source of the external NFET.
16 GATE output N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states.
17 GND power_in Exposed pad ground that must be soldered directly to the ground plane and also serves as the sense return for the switch current sense resistor.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Display Modules / LED Drivers / Display Drivers
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Minimum Operating Voltage VIN 4.5 V VIN Tied to INTVCC 2
VIN Shutdown IQ IQ 1 µA EN/UVLO = 0V, PWM = 0V 2
VIN Shutdown IQ IQ 6 µA EN/UVLO = 1.15V, PWM = 0V 2
VIN Operating IQ (Not Switching) IQ 2.2 mA PWM = 0V 2
VREF Voltage VREF 1.955 2.02 2.05 V -100µA ≤ IVREF ≤ 0µA 2
VREF Pull-Up Current 150 185 210 µA VREF = 0V 2
SENSE Current Limit Threshold 98 105 118 mV 2
DIM/SS Pull-Up Current 10 12 14 µA Current Out of Pin, DIM/SS = 0V 2
Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) VISP-ISN 242 250 258 mV CTRL ≥ 1.2V, ISP = 48V 3
Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) VISP-ISN 243 257 268 mV CTRL ≥ 1.2V, ISN = 0V 3
1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) VISP-ISN 21 25 30 mV CTRL = 0.2V, ISP = 48V 3
1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) VISP-ISN 17 28 39 mV CTRL = 0.2V, ISN = 0V 3
Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) VISP-ISN 96 100 104 mV CTRL = 0.5V, ISP = 48V 3
Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) VISP-ISN 95 105 115 mV CTRL = 0.5V, ISN = 0V 3
ISP/ISN Current Sense Amplifier Input Common Mode Range (VISN) VISN 0 80 V 3
CTRL Pin Range for Linear Current Sense Threshold Adjustment CTRL 0 1 V 3
CTRL Input Bias Current 50 100 nA Current Out of Pin 3
VC Standby Input Bias Current -20 20 nA PWM = 0V 3
FB Regulation Voltage (VFB) VFB 1.225 1.255 1.275 V ISP = ISN = 48V, 0V 3
FB Pin Input Bias Current 40 100 nA Current Out of Pin, FB = VFB 3
C/10 Inhibit for OPENLED Assertion (VISP-ISN) VISP-ISN 14 25 39 mV FB = VFB, ISN = 48V, 0V (LT3761 Only) 3
Switching Frequency fOSC 85 100 115 kHz RT = 95.3kΩ 3
Switching Frequency fOSC 925 1000 1050 kHz RT = 8.87kΩ 3
INTVCC Regulation Voltage INTVCC 7.6 7.85 8.05 V 10V ≤ VIN ≤ 60V 3
INTVCC Maximum Operating Voltage INTVCC 8.1 V 3
INTVCC Minimum Operating Voltage INTVCC 4.5 V 3
INTVCC Undervoltage Lockout 3.9 4.1 4.4 V EN/UVLO = 2V 4
INTVCC Current Limit 30 36 42 mA INTVCC = 6V, 8V ≤ VIN ≤ 60V 4
INTVCC Current in Shutdown 8 13 µA EN/UVLO = 0V, INTVCC = 8V 4
EN/UVLO Threshold Voltage Falling 1.18 1.22 1.26 V Falling 4
EN/UVLO Input Low Voltage 0.4 V IVIN Drops Below 1µA 4
EN/UVLO Pin Bias Current Low 1.7 2.3 2.7 µA EN/UVLO = 1.15V 4
EN/UVLO Pin Bias Current High 10 100 nA EN/UVLO = 1.33V 4
OPENLED Output Low 200 mV IOPENLED = 1mA (LT3761 Only) 4
PWM Falling Threshold 0.78 0.83 0.88 V 4
PWM Threshold Hysteresis (VPWMHYS) VPWMHYS 0.35 0.4 0.6 V IDIM/SS = 0µA 4
PWM Pull-Up Current (IPWMUP) IPWMUP 6 7.5 9 µA PWM = 0.7V, IDIM/SS = 0µA 4
PWM Pull-Down Current (IPWMDN) IPWMDN 68 88 110 µA PWM = 1.5V, IDIM/SS = 0µA 4
PWMOUT Duty Ratio for PWM Signal Generator 3.1 4.1 5.2 % IDIM/SS = -6.5µA 4
PWMOUT Duty Ratio for PWM Signal Generator 6.8 7.9 9.2 % IDIM/SS = 0µA 4
PWMOUT Duty Ratio for PWM Signal Generator 40 47.8 56 % IDIM/SS = 21.5µA 4
PWMOUT Duty Ratio for PWM Signal Generator 95 96.5 98 % IDIM/SS = 52µA 4
PWMOUT Signal Generator Frequency 215 300 435 Hz PWM = 47nF to GND, IDIM/SS = 0µA 4
PWMOUT Output Low (VOL) VOL 0.05 V PWM = 0V 4
GATE Output Low (VOL) VOL 0.1 V 4
Absolute Maximum VIN, EN/UVLO VIN, EN/UVLO 60 V 2
Absolute Maximum ISP, ISN ISP, ISN 80 V 2
Absolute Maximum INTVCC INTVCC 9.6 V 2
Absolute Maximum CTRL, OPENLED CTRL, OPENLED 15 V 2
Absolute Maximum FB, PWM, SYNC FB, PWM, SYNC 9.6 V 2
Absolute Maximum VC, VREF VC, VREF 3 V 2
Absolute Maximum RT, DIM/SS RT, DIM/SS 1.5 V 2
Absolute Maximum SENSE SENSE 0.5 V 2
Operating Ambient Temperature Range (LT3761E) TA -40 125 °C LT3761E 2
Storage Temperature Range TSTG -65 150 °C 2
Maximum Junction Temperature (E-grade) TJMAX 125 °C E-GRADE 2
Thermal Resistance Junction to Ambient θJA 43 °C/W 2
Thermal Resistance Junction to Case θJC 4 °C/W 2

CAD (KiCad official)

  • Symbol: LT3761EMSE#PBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt3761emse-pbf-etched.step / lt3761emse-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3761emse-pbf.step / lt3761emse-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (32 pp, sha256 733340007eac0a67, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF