3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3761EMSE#PBF
Analog Devices · LED Drivers · MSOP-16-EP
LT3761EMSE#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWMOUT | output | Buffered PWM signal driven from INTVCC for an LED load disconnect NMOS or level shift, toggling if FB exceeds VFB plus 60mV (typical). |
| 2 | FB | input | Voltage loop feedback regulated to 1.25V (nominal) that must not be left open and must be connected to GND if unused, with FB overvoltage threshold of VFB plus 60mV (typical). |
| 3 | ISN | input | Negative terminal connection of the current feedback resistor, with input bias current typically 20µA flowing into the pin when ISN is greater than INTVCC. |
| 4 | ISP | input | Positive terminal connection of the current feedback resistor, where an ISP-ISN difference above 600mV (typical) triggers an overcurrent event that drives GATE and PWMOUT low. |
| 5 | VC | passive | Transconductance error amplifier output that requires a capacitor to GND with a series resistor recommended for fast transient response, and is high impedance when PWM is low. |
| 6 | CTRL | input | Current sense threshold adjustment input that must not be left open, with VISP-ISN reaching the full-scale 250mV for CTRL above 1.2V. |
| 7 | VREF | power_in | Voltage reference output, typically 2V, that can supply up to 185µA (typical) to a resistor divider for the CTRL pin. |
| 8 | PWM | input | PWM input where a signal low turns off the switcher, and which must be connected to INTVCC if not used, with a capacitor to GND invoking a self-driving oscillator. |
| 9 | OPENLED | output | Open-drain pull-down output (LT3761 only) that asserts when FB is above VFB minus 50mV (typical) and ISP-ISN is below 25mV, and requires an external pull-up, usually to INTVCC. |
| 10 | DIM/SS | passive | Soft-start and PWMOUT dimming signal generator programming pin with a 12µA (typical) internal pull-up and a capacitor to GND of minimum 560pF when the PWMOUT generator is used. |
| 11 | RT | passive | Switching frequency adjustment pin set by a resistor to GND, which must not be left open and should be placed close to the IC. |
| 12 | EN/UVLO | input | Enable and undervoltage detect pin with a 1.22V falling threshold and 1.24V (typical) rising enable threshold, which must be tied to 0.4V or less to disable the device. |
| 13 | INTVCC | power_out | Current limited low dropout linear regulator output regulating to 7.85V (typical) from VIN, which must be bypassed with a 1µF ceramic capacitor placed close to the pin and exposed pad GND. |
| 14 | VIN | power_in | Power supply input for internal loads and the INTVCC regulator, which must be locally bypassed with a 0.22µF (or larger) low ESR capacitor placed close to the pin. |
| 15 | SENSE | input | Current sense input for the switch control loop that must be Kelvin connected to the positive terminal of the switch current sense resistor in the source of the external NFET. |
| 16 | GATE | output | N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states. |
| 17 | GND | power_in | Exposed pad ground that must be soldered directly to the ground plane and also serves as the sense return for the switch current sense resistor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Minimum Operating Voltage | VIN | 4.5 | V | VIN Tied to INTVCC | 2 | ||
| VIN Shutdown IQ | IQ | 1 | µA | EN/UVLO = 0V, PWM = 0V | 2 | ||
| VIN Shutdown IQ | IQ | 6 | µA | EN/UVLO = 1.15V, PWM = 0V | 2 | ||
| VIN Operating IQ (Not Switching) | IQ | 2.2 | mA | PWM = 0V | 2 | ||
| VREF Voltage | VREF | 1.955 | 2.02 | 2.05 | V | -100µA ≤ IVREF ≤ 0µA | 2 |
| VREF Pull-Up Current | 150 | 185 | 210 | µA | VREF = 0V | 2 | |
| SENSE Current Limit Threshold | 98 | 105 | 118 | mV | 2 | ||
| DIM/SS Pull-Up Current | 10 | 12 | 14 | µA | Current Out of Pin, DIM/SS = 0V | 2 | |
| Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 242 | 250 | 258 | mV | CTRL ≥ 1.2V, ISP = 48V | 3 |
| Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 243 | 257 | 268 | mV | CTRL ≥ 1.2V, ISN = 0V | 3 |
| 1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 21 | 25 | 30 | mV | CTRL = 0.2V, ISP = 48V | 3 |
| 1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 17 | 28 | 39 | mV | CTRL = 0.2V, ISN = 0V | 3 |
| Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 96 | 100 | 104 | mV | CTRL = 0.5V, ISP = 48V | 3 |
| Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 95 | 105 | 115 | mV | CTRL = 0.5V, ISN = 0V | 3 |
| ISP/ISN Current Sense Amplifier Input Common Mode Range (VISN) | VISN | 0 | 80 | V | 3 | ||
| CTRL Pin Range for Linear Current Sense Threshold Adjustment | CTRL | 0 | 1 | V | 3 | ||
| CTRL Input Bias Current | 50 | 100 | nA | Current Out of Pin | 3 | ||
| VC Standby Input Bias Current | -20 | 20 | nA | PWM = 0V | 3 | ||
| FB Regulation Voltage (VFB) | VFB | 1.225 | 1.255 | 1.275 | V | ISP = ISN = 48V, 0V | 3 |
| FB Pin Input Bias Current | 40 | 100 | nA | Current Out of Pin, FB = VFB | 3 | ||
| C/10 Inhibit for OPENLED Assertion (VISP-ISN) | VISP-ISN | 14 | 25 | 39 | mV | FB = VFB, ISN = 48V, 0V (LT3761 Only) | 3 |
| Switching Frequency | fOSC | 85 | 100 | 115 | kHz | RT = 95.3kΩ | 3 |
| Switching Frequency | fOSC | 925 | 1000 | 1050 | kHz | RT = 8.87kΩ | 3 |
| INTVCC Regulation Voltage | INTVCC | 7.6 | 7.85 | 8.05 | V | 10V ≤ VIN ≤ 60V | 3 |
| INTVCC Maximum Operating Voltage | INTVCC | 8.1 | V | 3 | |||
| INTVCC Minimum Operating Voltage | INTVCC | 4.5 | V | 3 | |||
| INTVCC Undervoltage Lockout | 3.9 | 4.1 | 4.4 | V | EN/UVLO = 2V | 4 | |
| INTVCC Current Limit | 30 | 36 | 42 | mA | INTVCC = 6V, 8V ≤ VIN ≤ 60V | 4 | |
| INTVCC Current in Shutdown | 8 | 13 | µA | EN/UVLO = 0V, INTVCC = 8V | 4 | ||
| EN/UVLO Threshold Voltage Falling | 1.18 | 1.22 | 1.26 | V | Falling | 4 | |
| EN/UVLO Input Low Voltage | 0.4 | V | IVIN Drops Below 1µA | 4 | |||
| EN/UVLO Pin Bias Current Low | 1.7 | 2.3 | 2.7 | µA | EN/UVLO = 1.15V | 4 | |
| EN/UVLO Pin Bias Current High | 10 | 100 | nA | EN/UVLO = 1.33V | 4 | ||
| OPENLED Output Low | 200 | mV | IOPENLED = 1mA (LT3761 Only) | 4 | |||
| PWM Falling Threshold | 0.78 | 0.83 | 0.88 | V | 4 | ||
| PWM Threshold Hysteresis (VPWMHYS) | VPWMHYS | 0.35 | 0.4 | 0.6 | V | IDIM/SS = 0µA | 4 |
| PWM Pull-Up Current (IPWMUP) | IPWMUP | 6 | 7.5 | 9 | µA | PWM = 0.7V, IDIM/SS = 0µA | 4 |
| PWM Pull-Down Current (IPWMDN) | IPWMDN | 68 | 88 | 110 | µA | PWM = 1.5V, IDIM/SS = 0µA | 4 |
| PWMOUT Duty Ratio for PWM Signal Generator | 3.1 | 4.1 | 5.2 | % | IDIM/SS = -6.5µA | 4 | |
| PWMOUT Duty Ratio for PWM Signal Generator | 6.8 | 7.9 | 9.2 | % | IDIM/SS = 0µA | 4 | |
| PWMOUT Duty Ratio for PWM Signal Generator | 40 | 47.8 | 56 | % | IDIM/SS = 21.5µA | 4 | |
| PWMOUT Duty Ratio for PWM Signal Generator | 95 | 96.5 | 98 | % | IDIM/SS = 52µA | 4 | |
| PWMOUT Signal Generator Frequency | 215 | 300 | 435 | Hz | PWM = 47nF to GND, IDIM/SS = 0µA | 4 | |
| PWMOUT Output Low (VOL) | VOL | 0.05 | V | PWM = 0V | 4 | ||
| GATE Output Low (VOL) | VOL | 0.1 | V | 4 | |||
| Absolute Maximum VIN, EN/UVLO | VIN, EN/UVLO | 60 | V | 2 | |||
| Absolute Maximum ISP, ISN | ISP, ISN | 80 | V | 2 | |||
| Absolute Maximum INTVCC | INTVCC | 9.6 | V | 2 | |||
| Absolute Maximum CTRL, OPENLED | CTRL, OPENLED | 15 | V | 2 | |||
| Absolute Maximum FB, PWM, SYNC | FB, PWM, SYNC | 9.6 | V | 2 | |||
| Absolute Maximum VC, VREF | VC, VREF | 3 | V | 2 | |||
| Absolute Maximum RT, DIM/SS | RT, DIM/SS | 1.5 | V | 2 | |||
| Absolute Maximum SENSE | SENSE | 0.5 | V | 2 | |||
| Operating Ambient Temperature Range (LT3761E) | TA | -40 | 125 | °C | LT3761E | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Maximum Junction Temperature (E-grade) | TJMAX | 125 | °C | E-GRADE | 2 | ||
| Thermal Resistance Junction to Ambient | θJA | 43 | °C/W | 2 | |||
| Thermal Resistance Junction to Case | θJC | 4 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT3761EMSE#PBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt3761emse-pbf-etched.step/lt3761emse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3761emse-pbf.step/lt3761emse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
733340007eac0a67, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).