main
History Download
Ray lmr38020sddar: specified limits as data (metadata.characteristics, 38 rows from the datasheet) 3987e8d

LMR38020SDDAR

Texas Instruments · DC-DC Converters · SOP-8-EP

LMR38020SDDAR from Texas Instruments, in a SOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Power and analog ground terminal; all electrical parameters measured with respect to this pin.
2 EN input Enable input to regulator; high = ON, low = OFF; can be connected directly to VIN; do not float.
3 VIN power_in Input supply to the regulator; requires high-quality bypass capacitor with short and wide traces to GND.
4 RT/SYNC input Resistor timing or external clock input; internal amplifier sets switching frequency from external resistor to ground; above PLL threshold becomes synchronization input for external clock.
5 FB input Feedback input to the regulator; connect to feedback voltage divider; do not float; do not ground.
6 PG tri_state Open-drain power-good flag output; high = power OK, low = power bad; pulls low when EN = low.
7 BOOT power_in Bootstrap supply voltage for the internal high-side driver; requires 100-nF capacitor to SW pin.
8 SW output Regulator switch node; connect to a power inductor.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOP-8-EP
Category Power Management (PMIC)
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range after start-up 4.2 80 V 4
Output voltage range for adjustable version 1 75 V 4
Frequency adjustment range 200 2200 kHz 4
Synchronization frequency range 300 2100 kHz 4
Output DC current range 0 2 A LMR38020 4
Operating junction temperature range TJ -40 150 °C 4
VIN to PGND -0.3 85 V 4
EN to PGND -0.3 V 4
FB to PGND -0.3 5.5 V 4
RT/SYNC to PGND -0.3 5.5 V 4
BOOT to SW -0.3 5.5 V 4
SW to PGND -0.3 85 V 4
SW to PGND transient -5 85.3 V less than 10-ns transients 4
PGOOD to PGND -0.3 20 V 4
Junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
Enable input high level VEN-H 1.1 1.25 1.4 V VEN rising 5
Enable input low level VEN-L 0.95 1.1 1.22 V VEN falling 5
Feedback reference voltage VREF 0.99 1 1.01 V Vin=4.2V to 80V, TJ=25°C, FPWM 5
Feedback reference voltage VREF 0.985 1 1.015 V FPWM 5
High-side current limit IHS-LIMIT 2.6 3.2 3.8 A 2A Version 5
Low-side current limit ILS-LIMIT 1.8 2.3 2.8 A 2A Version 5
Switching frequency FOSC 430 525 650 kHz RT = 49.9 kΩ 5
Shutdown quiescent current; measured at VIN pin ISD 3 10 µA VEN = 0 V 5
Minimum switch on-time tON-MIN 80 131 ns VIN =24 V, Iout = 1 A 5
Minimum switch off-time tOFF-MIN 190 300 ns 5
Spread of internal oscillator with spread spectrum enabled FSPREAD -8 8 % Spread spectrum enabled 6
Power-good upper threshold, rising, % of FB voltage VPG-HIGH-UP 110 112 114 % rising, % of FB voltage 6
Power-good lower threshold, falling, % of FB voltage VPG-LOW-DN 90 92 94 % falling, % of FB voltage 6
VIN operating input voltage range VIN 4.2 80 V 7
Adjustable output voltage regulation VOUT -1.5 2.5 % PFM operation 7
Junction-to-ambient thermal resistance RθJA 42.9 °C/W DDA (HSOIC), 8 pins 5
Junction-to-ambient thermal resistance with TI EVM board RθJA(Effecitve) 29 °C/W DDA (HSOIC), 8 pins 5
Junction-to-case (top) thermal resistance RθJC(top) 54 °C/W DDA (HSOIC), 8 pins 5
Junction-to-board thermal resistance RθJB 13.6 °C/W DDA (HSOIC), 8 pins 5
Junction-to-top characterization parameter ψJT 4.3 °C/W DDA (HSOIC), 8 pins 5
Junction-to-board characterization parameter ψJB 13.8 °C/W DDA (HSOIC), 8 pins 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 4.3 °C/W DDA (HSOIC), 8 pins 5

CAD (KiCad official)

  • Symbol: LMR38020SDDAR
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm
  • 3D model: SOP-8-EP (KiCad packages3D, STEP)
  • 3D model files: lmr38020sddar-etched.step / lmr38020sddar-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmr38020sddar.step / lmr38020sddar.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (41 pp, sha256 c0ab9b6fcda93544, retrieved 2026-10-03, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF