Generated by kicad-footprint-generator · KiCad file format 20260206
LMR38020SDDAR
Texas Instruments · DC-DC Converters · SOP-8-EP
LMR38020SDDAR from Texas Instruments, in a SOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Power and analog ground terminal; all electrical parameters measured with respect to this pin. |
| 2 | EN | input | Enable input to regulator; high = ON, low = OFF; can be connected directly to VIN; do not float. |
| 3 | VIN | power_in | Input supply to the regulator; requires high-quality bypass capacitor with short and wide traces to GND. |
| 4 | RT/SYNC | input | Resistor timing or external clock input; internal amplifier sets switching frequency from external resistor to ground; above PLL threshold becomes synchronization input for external clock. |
| 5 | FB | input | Feedback input to the regulator; connect to feedback voltage divider; do not float; do not ground. |
| 6 | PG | tri_state | Open-drain power-good flag output; high = power OK, low = power bad; pulls low when EN = low. |
| 7 | BOOT | power_in | Bootstrap supply voltage for the internal high-side driver; requires 100-nF capacitor to SW pin. |
| 8 | SW | output | Regulator switch node; connect to a power inductor. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOP-8-EP |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range after start-up | 4.2 | 80 | V | 4 | |||
| Output voltage range for adjustable version | 1 | 75 | V | 4 | |||
| Frequency adjustment range | 200 | 2200 | kHz | 4 | |||
| Synchronization frequency range | 300 | 2100 | kHz | 4 | |||
| Output DC current range | 0 | 2 | A | LMR38020 | 4 | ||
| Operating junction temperature range | TJ | -40 | 150 | °C | 4 | ||
| VIN to PGND | -0.3 | 85 | V | 4 | |||
| EN to PGND | -0.3 | V | 4 | ||||
| FB to PGND | -0.3 | 5.5 | V | 4 | |||
| RT/SYNC to PGND | -0.3 | 5.5 | V | 4 | |||
| BOOT to SW | -0.3 | 5.5 | V | 4 | |||
| SW to PGND | -0.3 | 85 | V | 4 | |||
| SW to PGND transient | -5 | 85.3 | V | less than 10-ns transients | 4 | ||
| PGOOD to PGND | -0.3 | 20 | V | 4 | |||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Enable input high level | VEN-H | 1.1 | 1.25 | 1.4 | V | VEN rising | 5 |
| Enable input low level | VEN-L | 0.95 | 1.1 | 1.22 | V | VEN falling | 5 |
| Feedback reference voltage | VREF | 0.99 | 1 | 1.01 | V | Vin=4.2V to 80V, TJ=25°C, FPWM | 5 |
| Feedback reference voltage | VREF | 0.985 | 1 | 1.015 | V | FPWM | 5 |
| High-side current limit | IHS-LIMIT | 2.6 | 3.2 | 3.8 | A | 2A Version | 5 |
| Low-side current limit | ILS-LIMIT | 1.8 | 2.3 | 2.8 | A | 2A Version | 5 |
| Switching frequency | FOSC | 430 | 525 | 650 | kHz | RT = 49.9 kΩ | 5 |
| Shutdown quiescent current; measured at VIN pin | ISD | 3 | 10 | µA | VEN = 0 V | 5 | |
| Minimum switch on-time | tON-MIN | 80 | 131 | ns | VIN =24 V, Iout = 1 A | 5 | |
| Minimum switch off-time | tOFF-MIN | 190 | 300 | ns | 5 | ||
| Spread of internal oscillator with spread spectrum enabled | FSPREAD | -8 | 8 | % | Spread spectrum enabled | 6 | |
| Power-good upper threshold, rising, % of FB voltage | VPG-HIGH-UP | 110 | 112 | 114 | % | rising, % of FB voltage | 6 |
| Power-good lower threshold, falling, % of FB voltage | VPG-LOW-DN | 90 | 92 | 94 | % | falling, % of FB voltage | 6 |
| VIN operating input voltage range | VIN | 4.2 | 80 | V | 7 | ||
| Adjustable output voltage regulation | VOUT | -1.5 | 2.5 | % | PFM operation | 7 | |
| Junction-to-ambient thermal resistance | RθJA | 42.9 | °C/W | DDA (HSOIC), 8 pins | 5 | ||
| Junction-to-ambient thermal resistance with TI EVM board | RθJA(Effecitve) | 29 | °C/W | DDA (HSOIC), 8 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 54 | °C/W | DDA (HSOIC), 8 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 13.6 | °C/W | DDA (HSOIC), 8 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 4.3 | °C/W | DDA (HSOIC), 8 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 13.8 | °C/W | DDA (HSOIC), 8 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.3 | °C/W | DDA (HSOIC), 8 pins | 5 |
CAD (KiCad official)
- Symbol:
LMR38020SDDAR - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
lmr38020sddar-etched.step/lmr38020sddar-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr38020sddar.step/lmr38020sddar.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (41 pp, sha256
c0ab9b6fcda93544, retrieved 2026-10-03, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).