Generated by kicad-footprint-generator · KiCad file format 20260206
LMR33610BDDAR
Texas Instruments · DC-DC Converters · SO-8
LMR33610BDDAR from Texas Instruments, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PGND | power_in | Power ground pin that connects to system ground and AGND with bypass capacitor using short wide traces. |
| 2 | VIN | power_in | Input supply to regulator rated 3.8 V to 36 V with high-quality bypass capacitor connected directly to this pin and PGND. |
| 3 | EN | input | Enable input to regulator where high = ON and low = OFF, can be connected directly to VIN, and must not float. |
| 4 | PG | output | Open-drain power-good flag output where high = power OK and low = power bad, pulls low when EN = low, and requires current limiting resistor to suitable voltage supply. |
| 5 | FB | input | Feedback input to regulator nominally 1 V for regulation, connected to tap point of feedback voltage divider, must not float or be grounded. |
| 6 | VCC | power_out | Internal 5-V LDO output (4.75 V to 5.25 V) supplying internal control circuits, requires 1-µF capacitor connected from this pin to GND, and must not be loaded with external circuits. |
| 7 | BOOT | power_in | Bootstrap supply voltage for internal high-side driver with 2.2 V undervoltage lockout threshold, requires 100-nF capacitor connected from this pin to SW. |
| 8 | SW | output | Regulator switch node driven between GND and VIN that connects to the power inductor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SO-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to PGND | VIN | -0.3 | 38 | V | 4 | ||
| EN to AGND | EN | -0.3 | V | 4 | |||
| FB to AGND | FB | -0.3 | 5.5 | V | 4 | ||
| PG to AGND | PG | 0 | 22 | V | 4 | ||
| AGND to PGND | AGND | -0.3 | 0.3 | V | 4 | ||
| SW to PGND | SW | -0.3 | V | 4 | |||
| SW to PGND less than 100-ns transients | SW | -3.5 | 38 | V | 4 | ||
| BOOT to SW | BOOT | -0.3 | 5.5 | V | 4 | ||
| VCC to AGND | VCC | -0.3 | 5.5 | V | 4 | ||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| Input voltage VIN to PGND | VIN | 3.8 | 36 | V | 4 | ||
| EN | EN | 0 | V | 4 | |||
| PG | PG | 0 | 18 | V | 4 | ||
| Adjustable output voltage | VOUT | 1 | 24 | V | 4 | ||
| Output current | IOUT | 0 | 1 | A | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Minimum operating input voltage | VIN | 3.8 | V | 5 | |||
| Non-switching input current; measured at VIN pin | IQ | 24 | 34 | µA | VFB = 1.2 V | 5 | |
| Shutdown quiescent current; measured at VIN pin | ISD | 5 | 10 | µA | EN = 0 | 5 | |
| EN input level required to start switching (rising threshold) | VEN-H | 1.2 | 1.231 | 1.26 | V | Rising threshold | 5 |
| Current into FB pin | IFB | 0.2 | 50 | nA | FB = 1 V | 5 | |
| Internal LDO output voltage appearing at the VCC pin | VCC | 4.75 | 5 | 5.25 | V | 6 V ≤ VIN ≤ 36 V | 5 |
| Feedback voltage | VFB | 0.985 | 1 | 1.015 | V | 5 | |
| High-side current limit | ISC | 2.9 | 3.4 | 4 | A | LMR33610 | 5 |
| Low-side current limit | ILIMIT | 1.95 | 2.35 | 2.9 | A | LMR33610 | 5 |
| Internal soft-start time | tSS | 2.9 | 4 | 6 | ms | 5 | |
| Power-good upper threshold - rising, % of FB voltage | VPG-HIGH-UP | 105 | 107 | 110 | % | 6 | |
| Power-good upper threshold – falling, % of FB voltage | VPG-HIGH-DN | 103 | 105 | 108 | % | 6 | |
| Power-good lower threshold – rising, % of FB voltage | VPG-LOW-UP | 92 | 94 | 97 | % | 6 | |
| Power-good lower threshold – falling, % of FB voltage | VPG-LOW-DN | 90 | 92 | 95 | % | 6 | |
| Power-good glitch filter delay | tPG | 60 | 170 | µs | 6 | ||
| Power-good flag RDSON | RPG | 76 | 150 | Ω | VIN = 12 V, VEN = 4 V | 6 | |
| Power-good flag RDSON | RPG | 35 | 60 | Ω | VEN = 0 V | 6 | |
| Switching frequency "B" version | fSW | 1.2 | 1.4 | 1.6 | MHz | 6 | |
| High-side MOSFET ON-resistance | RDS-ON-HS | 95 | 160 | mΩ | DDA package | 6 | |
| Low-side MOSFET ON-resistance | RDS-ON-LS | 66 | 110 | mΩ | DDA package | 6 | |
| Minimum switch on time | tON-MIN | 75 | 108 | ns | DDA package | 6 | |
| Minimum switch off time | tOFF-MIN | 50 | 85 | ns | DDA package | 6 | |
| Maximum switch on time | tON-MAX | 7 | 9 | µs | 6 | ||
| Output voltage regulation for VOUT = 5 V | VOUT | -1.5 | 2.5 | % | VOUT = 5 V, VIN = 7 V to 36 V, IOUT = 0 A to max. load | 7 | |
| Output voltage regulation for VOUT = 5 V | VOUT | -1.5 | 1.5 | % | VOUT = 5 V, VIN = 7 V to 36 V, IOUT = 1 A to max. load | 7 | |
| Output voltage regulation for VOUT = 3.3 V | VOUT | -1.5 | 2.5 | % | VOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 0 A to max. load | 7 | |
| Output voltage regulation for VOUT = 3.3 V | VOUT | -1.5 | 1.5 | % | VOUT = 3.3 V, VIN = 3.8 V to 36 V, IOUT = 1 A to max. load | 7 | |
| EN input level required to turn on internal LDO (rising threshold) | VEN-VCC-H | 1 | V | Rising threshold | 5 | ||
| EN input level required to turn off internal LDO (falling threshold) | VEN-VCC-L | 0.3 | V | Falling threshold | 5 | ||
| Hysteresis below VEN-H | VEN-HYS | 100 | mV | Hysteresis below VEN-H; falling | 5 | ||
| Enable input leakage current | ILKG-EN | 0.2 | nA | VEN = 3.3 V | 5 | ||
| Bootstrap voltage undervoltage lock-out threshold | VBOOT-UVLO | 2.2 | V | 5 | |||
| Minimum peak inductor current | IPEAK-MIN | 0.6 | A | LMR33610 | 5 | ||
| Minimum input voltage for proper PG function | VIN-PG | 2 | V | 50-µA, EN = 0 V | 6 | ||
| PG logic low output | VPG | 0.2 | V | 50-µA, EN = 0 V, VIN = 2V | 6 | ||
| Input supply current when in regulation | ISUPPLY | 25 | µA | VIN = 12 V, VOUT = 3.3 V, IOUT = 0 A, RFBT = 1 MΩ | 7 | ||
| Dropout voltage (VIN – VOUT) | VDROP | 150 | mV | VOUT = 5 V, IOUT = 1A; dropout at -1% of regulation, fSW = 140 kHz | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 42.9 | °C/W | DDA (HSOIC) 8 pins; JESD 51-7, 4-layer JEDEC board | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 54 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 13.6 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 4.3 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 13.8 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.3 | °C/W | DDA (HSOIC) 8 pins | 5 |
CAD (KiCad official)
- Symbol:
LMR33610BDDAR - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
lmr33610bddar-etched.step/lmr33610bddar-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr33610bddar.step/lmr33610bddar.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (41 pp, sha256
2dcad538089d5df2, retrieved 2026-09-24, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).