main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lmh6881sq: viewers rendered from the public page · Ray
lmh6881sq-etched.glb Publish 0.1.0 · Ray
lmh6881sq-etched.step lmh6881sq: factory component page (tier=mfr) · Ray
lmh6881sq-hero.glb lmh6881sq: hero GLB from the etched model (keeps the MPN mark) · Ray
lmh6881sq-hero.overlay.json Publish 0.1.0 · Ray
lmh6881sq.glb Publish 0.1.0 · Ray
lmh6881sq.kicad_mod Publish 0.1.0 · Ray
lmh6881sq.kicad_sym Publish 0.1.0 · Ray
lmh6881sq.lbr Publish 0.1.0 · Ray
lmh6881sq.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 25 pins · Ray

LMH6881SQ

Texas Instruments · Differential OpAmps · WQFN-24-EP(4x4)

LMH6881SQ from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected Not connected; the datasheet gives no function for this pin.
2 OCM input Output common-mode control with a gain of 2; OCM should be 1 V to 1.5 V to set the output common mode at 2 V to 3 V, must be driven from a low-noise external source, and must not be left floating.
3 D1, SDI input In parallel mode it is attenuator control bit 1 (weight 2); in serial mode it is the SPI serial data input (SDI), with logic levels of VIL 0.4 V max and VIH 2.0 V to 5.0 V.
4 D0, SDO bidirectional In parallel mode it is attenuator control bit 0 (internally biased low); in serial mode it is the open-emitter SPI serial data output (SDO), which requires an external bias resistor of 180 Ω to 400 Ω.
5 SPI input Mode select: logic 0 (or left open, via internal weak pulldown) selects parallel mode and logic 1 selects serial SPI mode.
6 GND power_in Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins.
7 GND power_in Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins.
8 INMS input Single-ended input minus (negative) with 50 Ω termination; an external 50-Ω resistor is required for single-ended signals and the differential inputs must be left disconnected in that case.
9 INMD input Differential input minus (negative) with an internal 100-Ω resistive termination; single-ended inputs must be left disconnected when used.
10 INPD input Differential input plus (positive) with an internal 100-Ω resistive termination; single-ended inputs must be left disconnected when used.
11 INPS input Single-ended input plus (positive) with 50 Ω termination; an external 50-Ω resistor is required for single-ended signals and the differential inputs must be left disconnected in that case.
12 GND power_in Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins.
13 GND power_in Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins.
14 NC unconnected Not connected; the datasheet gives no function for this pin.
15 D2, CLK input In parallel mode it is attenuator control bit 2 (weight 2); in serial mode it is the SPI serial clock (CLK), which registers SDI on the rising edge.
16 D3, CS input In parallel mode it is attenuator control bit 3 (weight 2); in serial mode it is the active-low SPI chip select (CS), with each write being 16 bits.
17 SD input Shutdown in parallel mode: 0 = amplifier on, 1 = amplifier off; the pin is disabled in serial mode.
18 NC unconnected Not connected; the datasheet gives no function for this pin.
19 VCC power_in Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V).
20 VCC power_in Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V).
21 OUTM output Differential output minus (negative) with low impedance; the output common mode is set by the OCM pin.
22 OUTP output Differential output plus (positive) with low impedance; the output common mode is set by the OCM pin.
23 VCC power_in Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V).
24 VCC power_in Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V).
25 GND (exposed thermal pad) power_in Exposed thermal pad, internally bonded to the ground pins, which is the primary heat path and should be soldered to the PCB.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-24-EP(4x4)
Category Operational Amplifier/Comparator
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (VCC) VCC 4.75 5.25 V Over operating free-air temperature range 5
Temperature Range -40 85 °C 5
Differential Voltage Between Any Two Grounds 10 mV 5
Analog Input Voltage Range, AC Coupled 0 V AC coupled 5
Positive Supply Voltage (VCC) VCC -0.6 5.5 V 4
Differential Voltage between Any Two Grounds 200 mV 4
Analog Input Voltage Range -0.6 5.5 V 4
Digital Input Voltage Range -0.6 5.5 V 4
Junction Temperature 150 °C 4
Soldering Information 260 °C Infrared or Convection (30 sec) 4
Storage temperature range Tstg -65 150 °C 4
Maximum Input Voltage Swing 2.85 VPPD Volts peak to peak, differential 6
Maximum Differential Output Voltage Swing 6 VPPD Differential, f < 10 MHz 6
Minimum Gain 6 dB Parallel Inputs, Rs = 100 Ω 6
Maximum Voltage Gain 26 dB Parallel Inputs (INPD and INMD), Rs = 100 Ω 6
Maximum Voltage Gain 26.6 dB Single-ended input (INMS or INPS), 50-Ω Rs and 50-Ω termination on unused input. 6
Gain Step Error -0.125 0.125 dB Any two adjacent steps over entire range 6
Gain Step Phase Shift -3 3 Degrees Any two adjacent steps over entire range 6
Supply Current ICC 100 135 mA 6
Logic Input Low Voltage VIL 0.4 V 6
Logic Input High Voltage VIH 2 5 V 6
SPI Clock Frequency fCLK 10 50 MHz 50% duty cycle 6
Junction-to-ambient thermal resistance RθJA 38.1 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 39.9 °C/W 5
Junction-to-board thermal resistance RθJB 16.7 °C/W 5
Junction-to-top characterization parameter ψJT 0.5 °C/W 5
Junction-to-board characterization parameter ψJB 16.8 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 5.8 °C/W 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper underneath the input and output pins of the device also helps in minimizing parasitic capacitance affecting the high-frequency signals near the PCB and package junctions. The LMH6881 evaluation board 27

CAD (KiCad official)

  • Symbol: LMH6881SQ
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lmh6881sq-etched.step / lmh6881sq-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmh6881sq.step / lmh6881sq.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (37 pp, sha256 8ca06ef36842f1bc, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF