3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLMH6881SQ
Texas Instruments · Differential OpAmps · WQFN-24-EP(4x4)
LMH6881SQ from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Not connected; the datasheet gives no function for this pin. |
| 2 | OCM | input | Output common-mode control with a gain of 2; OCM should be 1 V to 1.5 V to set the output common mode at 2 V to 3 V, must be driven from a low-noise external source, and must not be left floating. |
| 3 | D1, SDI | input | In parallel mode it is attenuator control bit 1 (weight 2); in serial mode it is the SPI serial data input (SDI), with logic levels of VIL 0.4 V max and VIH 2.0 V to 5.0 V. |
| 4 | D0, SDO | bidirectional | In parallel mode it is attenuator control bit 0 (internally biased low); in serial mode it is the open-emitter SPI serial data output (SDO), which requires an external bias resistor of 180 Ω to 400 Ω. |
| 5 | SPI | input | Mode select: logic 0 (or left open, via internal weak pulldown) selects parallel mode and logic 1 selects serial SPI mode. |
| 6 | GND | power_in | Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins. |
| 7 | GND | power_in | Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins. |
| 8 | INMS | input | Single-ended input minus (negative) with 50 Ω termination; an external 50-Ω resistor is required for single-ended signals and the differential inputs must be left disconnected in that case. |
| 9 | INMD | input | Differential input minus (negative) with an internal 100-Ω resistive termination; single-ended inputs must be left disconnected when used. |
| 10 | INPD | input | Differential input plus (positive) with an internal 100-Ω resistive termination; single-ended inputs must be left disconnected when used. |
| 11 | INPS | input | Single-ended input plus (positive) with 50 Ω termination; an external 50-Ω resistor is required for single-ended signals and the differential inputs must be left disconnected in that case. |
| 12 | GND | power_in | Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins. |
| 13 | GND | power_in | Ground pin; connect to a low-impedance ground plane, as all pin voltages are referenced to the ground pins. |
| 14 | NC | unconnected | Not connected; the datasheet gives no function for this pin. |
| 15 | D2, CLK | input | In parallel mode it is attenuator control bit 2 (weight 2); in serial mode it is the SPI serial clock (CLK), which registers SDI on the rising edge. |
| 16 | D3, CS | input | In parallel mode it is attenuator control bit 3 (weight 2); in serial mode it is the active-low SPI chip select (CS), with each write being 16 bits. |
| 17 | SD | input | Shutdown in parallel mode: 0 = amplifier on, 1 = amplifier off; the pin is disabled in serial mode. |
| 18 | NC | unconnected | Not connected; the datasheet gives no function for this pin. |
| 19 | VCC | power_in | Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V). |
| 20 | VCC | power_in | Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V). |
| 21 | OUTM | output | Differential output minus (negative) with low impedance; the output common mode is set by the OCM pin. |
| 22 | OUTP | output | Differential output plus (positive) with low impedance; the output common mode is set by the OCM pin. |
| 23 | VCC | power_in | Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V). |
| 24 | VCC | power_in | Power supply pin; valid supply range is 4.75 V to 5.25 V (nominal 5 V). |
| 25 | GND (exposed thermal pad) | power_in | Exposed thermal pad, internally bonded to the ground pins, which is the primary heat path and should be soldered to the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24-EP(4x4) |
| Category | Operational Amplifier/Comparator |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VCC) | VCC | 4.75 | 5.25 | V | Over operating free-air temperature range | 5 | |
| Temperature Range | -40 | 85 | °C | 5 | |||
| Differential Voltage Between Any Two Grounds | 10 | mV | 5 | ||||
| Analog Input Voltage Range, AC Coupled | 0 | V | AC coupled | 5 | |||
| Positive Supply Voltage (VCC) | VCC | -0.6 | 5.5 | V | 4 | ||
| Differential Voltage between Any Two Grounds | 200 | mV | 4 | ||||
| Analog Input Voltage Range | -0.6 | 5.5 | V | 4 | |||
| Digital Input Voltage Range | -0.6 | 5.5 | V | 4 | |||
| Junction Temperature | 150 | °C | 4 | ||||
| Soldering Information | 260 | °C | Infrared or Convection (30 sec) | 4 | |||
| Storage temperature range | Tstg | -65 | 150 | °C | 4 | ||
| Maximum Input Voltage Swing | 2.85 | VPPD | Volts peak to peak, differential | 6 | |||
| Maximum Differential Output Voltage Swing | 6 | VPPD | Differential, f < 10 MHz | 6 | |||
| Minimum Gain | 6 | dB | Parallel Inputs, Rs = 100 Ω | 6 | |||
| Maximum Voltage Gain | 26 | dB | Parallel Inputs (INPD and INMD), Rs = 100 Ω | 6 | |||
| Maximum Voltage Gain | 26.6 | dB | Single-ended input (INMS or INPS), 50-Ω Rs and 50-Ω termination on unused input. | 6 | |||
| Gain Step Error | -0.125 | 0.125 | dB | Any two adjacent steps over entire range | 6 | ||
| Gain Step Phase Shift | -3 | 3 | Degrees | Any two adjacent steps over entire range | 6 | ||
| Supply Current | ICC | 100 | 135 | mA | 6 | ||
| Logic Input Low Voltage | VIL | 0.4 | V | 6 | |||
| Logic Input High Voltage | VIH | 2 | 5 | V | 6 | ||
| SPI Clock Frequency | fCLK | 10 | 50 | MHz | 50% duty cycle | 6 | |
| Junction-to-ambient thermal resistance | RθJA | 38.1 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 39.9 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 16.7 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 0.5 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 16.8 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 5.8 | °C/W | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | underneath the input and output pins of the device also helps in minimizing parasitic capacitance affecting the high-frequency signals near the PCB and package junctions. The LMH6881 evaluation board | 27 |
CAD (KiCad official)
- Symbol:
LMH6881SQ - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lmh6881sq-etched.step/lmh6881sq-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmh6881sq.step/lmh6881sq.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
8ca06ef36842f1bc, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).