Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM536035QPWPRQ1

Texas Instruments · DC-DC Converters · HTSSOP-16

LM536035QPWPRQ1 from Texas Instruments, in a HTSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW output Regulator switching node connected to power inductor; maximum voltage VIN+0.3V with transient tolerance to 42V for 100ns.
2 SW output Regulator switching node connected to power inductor; connect directly to pin 1 at PCB; maximum voltage VIN+0.3V.
3 CBOOT power_in Bootstrap capacitor supply for high-side gate driver; maximum voltage 3.6V relative to SW; connect 470nF capacitor to SW.
4 VCC power_out Internal regulated 3.15V supply output for control circuits; maximum voltage 4.2V; connect 3.3µF capacitor to GND, no external loads.
5 BIAS input Feedback input connected to output voltage point for regulator control; maximum voltage 16V; current draw 47-78µA at VBIAS=5V.
6 SYNC input Synchronization clock input for frequency synchronization; range 1.9-2.3MHz; logic levels VIH=1.5V, VIL=0.4V; connect to GND if unused.
7 FPWM input PWM/PFM mode selection input; high enables forced PWM, low enables automatic mode; logic levels VIH=1.5V, VIL=0.4V.
8 RESET tri_state Open-drain power-status output; maximum current 1.2mA; low when EN=low or fault detected, high when output ≥107% nominal voltage.
9 FB input Feedback voltage input for output regulation; input impedance 1MΩ for both 5V and 3.3V options; do not float or ground.
10 AGND power_in Analog ground reference for all electrical measurements; maximum differential to PGND ±2V for transients ≤1µs per absolute maximum.
11 EN input Enable input for regulator control; threshold rising 1.7V, falling 0.8V with 0.45V hysteresis; maximum voltage 40V; high=ON, low=OFF.
12 VIN power_in Input power supply; voltage range 3.9-36V nominal, maximum sustained 42V for ≤500ms; connect high-quality bypass capacitor(s) to PGND.
13 VIN power_in Input power supply; voltage range 3.9-36V nominal, maximum sustained 42V for ≤500ms; connect directly to pin 12 at PCB.
14 N/C unconnected No internal connection to device.
15 PGND power_in Power ground for low-side MOSFET driver; connect to AGND and system ground; connect directly to pin 16 at PCB.
16 PGND power_in Power ground for low-side MOSFET driver; connect to AGND and system ground; connect directly to pin 15 at PCB.
17 EP power_in Exposed die-attach paddle providing power ground; junction-to-case thermal resistance 1.7°C/W; connect to ground plane for thermal and EMI control.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16
Category Power Management (PMIC)
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN 3.9 36 V 5
Output voltage: fixed 5 V 0 5 V Fixed 5 V option 5
Output current for LM53603-Q1 0 3 A 5
RESET pin current 0 1 mA 5
Operating junction temperature TJ -40 150 °C 5
Initial reference voltage accuracy -1 1 % VIN = 3.8 V to 36 V, FPWM, TJ = 25°C; FB for 5 V and 3.3 V options 6
Initial reference voltage accuracy -1.25 1.25 % VIN = 3.8 V to 36 V, FPWM 6
Absolute maximum VIN to AGND, PGND VIN -0.3 40 V 4
Absolute maximum SW to AGND, PGND SW -0.3 V 4
Absolute maximum CBOOT to SW CBOOT -0.3 3.6 V 4
Absolute maximum EN to AGND, PGND EN -0.3 40 V 4
Absolute maximum BIAS to AGND, PGND BIAS -0.3 16 V 4
Absolute maximum FB to AGND, PGND FB -0.3 16 V Fixed 5 V and 3.3 V 4
Absolute maximum RESET to AGND, PGND RESET -0.3 8 V 4
Absolute maximum SYNC, FPWM to AGND, PGND SYNC, FPWM -0.3 5.5 V 4
Absolute maximum VCC to AGND, PGND VCC -0.3 4.2 V 4
Absolute maximum RESET pin current RESET -0.1 1.2 mA 4
Absolute maximum AGND to PGND AGND-PGND -0.3 0.3 V 4
Storage temperature Tstg -40 150 °C 4
Minimum input voltage to operate, rising VIN-operate 3.2 3.95 V Rising 6
Minimum input voltage to operate, falling VIN-operate 2.9 3.55 V Falling 6
Operating quiescent current IQ 8 13 µA VBIAS = 5 V, measured at VIN pin; TJ = -40°C to 125°C 6
Current into the BIAS pin IB 47 78 µA VBIAS = 5 V, FPWM = 3.3 V 6
RESET upper threshold voltage VRESET 105 107 110 % Rising, % of nominal Vout 6
RESET lower threshold voltage VRESET 92 94 96.5 % Falling, % of nominal Vout 6
Low level RESET pin output voltage VOL 0.4 V 50 µA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V 6
Minimum input voltage for proper RESET function VMIN 1.5 V 50 µA pull-up to RESET pin, VEN = 0 V, TJ = 25°C 6
Enable input threshold voltage, rising VEN 1.7 2 V Rising 6
Enable input threshold voltage, hysteresis 0.45 0.55 V Hysteresis, below 6
Enable input threshold for full shutdown, falling VEN-off 0.8 V Falling; EN input voltage required for complete shutdown of the regulator 6
Logic input high level, FPWM and SYNC pins VIH 1.5 V Logic input levels on FPWM and SYNC pins 6
Logic input low level, FPWM and SYNC pins VIL 0.4 V Logic input levels on FPWM and SYNC pins 6
High side switch current limit IHS 4.5 6.2 A LM53603-Q1 6
Low side switch current limit ILS 3 3.6 4.3 A LM53603-Q1 7
High side MOSFET resistance Rdson 135 290 mΩ 7
Low side MOSFET resistance Rdson 60 125 mΩ 7
Switching frequency FSW 1.85 2.1 2.35 MHz VIN = 3.8 V to 18 V 7
Synchronizing frequency range FSYNC 1.9 2.1 2.3 MHz 7
Thermal shutdown threshold, rising TSD 162 178 °C Rising 7
Minimum switch on-time TON 50 80 ns VIN = 20 V 8
Minimum switch off-time TOFF 125 200 ns VIN = 3.8 V 8
Delay time to RESET high signal TRESET-act 2 3 4 ms 8
Glitch filter time for RESET function TRESET-filter 12 25 45 µs 8
Soft-start time TSS 1 2 3 ms 8
Turn-on delay TEN 0.7 0.8 ms CVCC = 1 µF 8
Junction-to-ambient thermal resistance RθJA 38.9 °C/W JESD 51-7, 4-layer JEDEC board 5
Junction-to-case (top) thermal resistance RθJC(top) 24.3 °C/W JESD 51-7, 4-layer JEDEC board 5
Junction-to-board thermal resistance RθJB 19.9 °C/W JESD 51-7, 4-layer JEDEC board 5
Junction-to-top characterization parameter ψJT 0.7 °C/W JESD 51-7, 4-layer JEDEC board 5
Junction-to-board characterization parameter ψJB 19.7 °C/W JESD 51-7, 4-layer JEDEC board 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 1.7 °C/W JESD 51-7, 4-layer JEDEC board 5

CAD (KiCad official)

  • Symbol: LM536035QPWPRQ1
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16 (KiCad packages3D, STEP)
  • 3D model files: lm536035qpwprq1-etched.step / lm536035qpwprq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm536035qpwprq1.step / lm536035qpwprq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (42 pp, sha256 b2d0d78814aaf2aa, retrieved 2026-10-06, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF