Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LM536035QPWPRQ1
Texas Instruments · DC-DC Converters · HTSSOP-16
LM536035QPWPRQ1 from Texas Instruments, in a HTSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Regulator switching node connected to power inductor; maximum voltage VIN+0.3V with transient tolerance to 42V for 100ns. |
| 2 | SW | output | Regulator switching node connected to power inductor; connect directly to pin 1 at PCB; maximum voltage VIN+0.3V. |
| 3 | CBOOT | power_in | Bootstrap capacitor supply for high-side gate driver; maximum voltage 3.6V relative to SW; connect 470nF capacitor to SW. |
| 4 | VCC | power_out | Internal regulated 3.15V supply output for control circuits; maximum voltage 4.2V; connect 3.3µF capacitor to GND, no external loads. |
| 5 | BIAS | input | Feedback input connected to output voltage point for regulator control; maximum voltage 16V; current draw 47-78µA at VBIAS=5V. |
| 6 | SYNC | input | Synchronization clock input for frequency synchronization; range 1.9-2.3MHz; logic levels VIH=1.5V, VIL=0.4V; connect to GND if unused. |
| 7 | FPWM | input | PWM/PFM mode selection input; high enables forced PWM, low enables automatic mode; logic levels VIH=1.5V, VIL=0.4V. |
| 8 | RESET | tri_state | Open-drain power-status output; maximum current 1.2mA; low when EN=low or fault detected, high when output ≥107% nominal voltage. |
| 9 | FB | input | Feedback voltage input for output regulation; input impedance 1MΩ for both 5V and 3.3V options; do not float or ground. |
| 10 | AGND | power_in | Analog ground reference for all electrical measurements; maximum differential to PGND ±2V for transients ≤1µs per absolute maximum. |
| 11 | EN | input | Enable input for regulator control; threshold rising 1.7V, falling 0.8V with 0.45V hysteresis; maximum voltage 40V; high=ON, low=OFF. |
| 12 | VIN | power_in | Input power supply; voltage range 3.9-36V nominal, maximum sustained 42V for ≤500ms; connect high-quality bypass capacitor(s) to PGND. |
| 13 | VIN | power_in | Input power supply; voltage range 3.9-36V nominal, maximum sustained 42V for ≤500ms; connect directly to pin 12 at PCB. |
| 14 | N/C | unconnected | No internal connection to device. |
| 15 | PGND | power_in | Power ground for low-side MOSFET driver; connect to AGND and system ground; connect directly to pin 16 at PCB. |
| 16 | PGND | power_in | Power ground for low-side MOSFET driver; connect to AGND and system ground; connect directly to pin 15 at PCB. |
| 17 | EP | power_in | Exposed die-attach paddle providing power ground; junction-to-case thermal resistance 1.7°C/W; connect to ground plane for thermal and EMI control. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16 |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 3.9 | 36 | V | 5 | ||
| Output voltage: fixed 5 V | 0 | 5 | V | Fixed 5 V option | 5 | ||
| Output current for LM53603-Q1 | 0 | 3 | A | 5 | |||
| RESET pin current | 0 | 1 | mA | 5 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Initial reference voltage accuracy | -1 | 1 | % | VIN = 3.8 V to 36 V, FPWM, TJ = 25°C; FB for 5 V and 3.3 V options | 6 | ||
| Initial reference voltage accuracy | -1.25 | 1.25 | % | VIN = 3.8 V to 36 V, FPWM | 6 | ||
| Absolute maximum VIN to AGND, PGND | VIN | -0.3 | 40 | V | 4 | ||
| Absolute maximum SW to AGND, PGND | SW | -0.3 | V | 4 | |||
| Absolute maximum CBOOT to SW | CBOOT | -0.3 | 3.6 | V | 4 | ||
| Absolute maximum EN to AGND, PGND | EN | -0.3 | 40 | V | 4 | ||
| Absolute maximum BIAS to AGND, PGND | BIAS | -0.3 | 16 | V | 4 | ||
| Absolute maximum FB to AGND, PGND | FB | -0.3 | 16 | V | Fixed 5 V and 3.3 V | 4 | |
| Absolute maximum RESET to AGND, PGND | RESET | -0.3 | 8 | V | 4 | ||
| Absolute maximum SYNC, FPWM to AGND, PGND | SYNC, FPWM | -0.3 | 5.5 | V | 4 | ||
| Absolute maximum VCC to AGND, PGND | VCC | -0.3 | 4.2 | V | 4 | ||
| Absolute maximum RESET pin current | RESET | -0.1 | 1.2 | mA | 4 | ||
| Absolute maximum AGND to PGND | AGND-PGND | -0.3 | 0.3 | V | 4 | ||
| Storage temperature | Tstg | -40 | 150 | °C | 4 | ||
| Minimum input voltage to operate, rising | VIN-operate | 3.2 | 3.95 | V | Rising | 6 | |
| Minimum input voltage to operate, falling | VIN-operate | 2.9 | 3.55 | V | Falling | 6 | |
| Operating quiescent current | IQ | 8 | 13 | µA | VBIAS = 5 V, measured at VIN pin; TJ = -40°C to 125°C | 6 | |
| Current into the BIAS pin | IB | 47 | 78 | µA | VBIAS = 5 V, FPWM = 3.3 V | 6 | |
| RESET upper threshold voltage | VRESET | 105 | 107 | 110 | % | Rising, % of nominal Vout | 6 |
| RESET lower threshold voltage | VRESET | 92 | 94 | 96.5 | % | Falling, % of nominal Vout | 6 |
| Low level RESET pin output voltage | VOL | 0.4 | V | 50 µA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V | 6 | ||
| Minimum input voltage for proper RESET function | VMIN | 1.5 | V | 50 µA pull-up to RESET pin, VEN = 0 V, TJ = 25°C | 6 | ||
| Enable input threshold voltage, rising | VEN | 1.7 | 2 | V | Rising | 6 | |
| Enable input threshold voltage, hysteresis | 0.45 | 0.55 | V | Hysteresis, below | 6 | ||
| Enable input threshold for full shutdown, falling | VEN-off | 0.8 | V | Falling; EN input voltage required for complete shutdown of the regulator | 6 | ||
| Logic input high level, FPWM and SYNC pins | VIH | 1.5 | V | Logic input levels on FPWM and SYNC pins | 6 | ||
| Logic input low level, FPWM and SYNC pins | VIL | 0.4 | V | Logic input levels on FPWM and SYNC pins | 6 | ||
| High side switch current limit | IHS | 4.5 | 6.2 | A | LM53603-Q1 | 6 | |
| Low side switch current limit | ILS | 3 | 3.6 | 4.3 | A | LM53603-Q1 | 7 |
| High side MOSFET resistance | Rdson | 135 | 290 | mΩ | 7 | ||
| Low side MOSFET resistance | Rdson | 60 | 125 | mΩ | 7 | ||
| Switching frequency | FSW | 1.85 | 2.1 | 2.35 | MHz | VIN = 3.8 V to 18 V | 7 |
| Synchronizing frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | 7 | |
| Thermal shutdown threshold, rising | TSD | 162 | 178 | °C | Rising | 7 | |
| Minimum switch on-time | TON | 50 | 80 | ns | VIN = 20 V | 8 | |
| Minimum switch off-time | TOFF | 125 | 200 | ns | VIN = 3.8 V | 8 | |
| Delay time to RESET high signal | TRESET-act | 2 | 3 | 4 | ms | 8 | |
| Glitch filter time for RESET function | TRESET-filter | 12 | 25 | 45 | µs | 8 | |
| Soft-start time | TSS | 1 | 2 | 3 | ms | 8 | |
| Turn-on delay | TEN | 0.7 | 0.8 | ms | CVCC = 1 µF | 8 | |
| Junction-to-ambient thermal resistance | RθJA | 38.9 | °C/W | JESD 51-7, 4-layer JEDEC board | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 24.3 | °C/W | JESD 51-7, 4-layer JEDEC board | 5 | ||
| Junction-to-board thermal resistance | RθJB | 19.9 | °C/W | JESD 51-7, 4-layer JEDEC board | 5 | ||
| Junction-to-top characterization parameter | ψJT | 0.7 | °C/W | JESD 51-7, 4-layer JEDEC board | 5 | ||
| Junction-to-board characterization parameter | ψJB | 19.7 | °C/W | JESD 51-7, 4-layer JEDEC board | 5 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.7 | °C/W | JESD 51-7, 4-layer JEDEC board | 5 |
CAD (KiCad official)
- Symbol:
LM536035QPWPRQ1 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
lm536035qpwprq1-etched.step/lm536035qpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm536035qpwprq1.step/lm536035qpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
b2d0d78814aaf2aa, retrieved 2026-10-06, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).