main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lm5045sq: viewers · Ray
lm5045sq-etched.glb Publish 0.1.0 · Ray
lm5045sq-etched.step lm5045sq: factory component page (tier=lcsc) · Ray
lm5045sq-hero.glb lm5045sq: hero GLB from the etched model (keeps the MPN mark) · Ray
lm5045sq-hero.overlay.json Publish 0.1.0 · Ray
lm5045sq.glb Publish 0.1.0 · Ray
lm5045sq.kicad_mod Publish 0.1.0 · Ray
lm5045sq.kicad_sym Publish 0.1.0 · Ray
lm5045sq.lbr Publish 0.1.0 · Ray
lm5045sq.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

LM5045SQ

Texas Instruments · AC-DC Controllers & Regulators · WQFN-28-EP(5x5)

LM5045SQ from Texas Instruments, in a WQFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SLOPE output Provides a 0 to 100µA ramp current source for slope compensation in current-mode control; must be grounded if slope compensation is not needed.
2 COMP input PWM input where an external optocoupler sinks current into an internal NPN current mirror; maximum duty cycle at zero input current and zero duty cycle at 1mA.
3 REF power_out 5V reference output with 15mA maximum output current; decouple locally with a 0.1µF capacitor.
4 RT/SYNC input Oscillator frequency set by a resistor to AGND; synchronization by AC-coupled pulses that raise the pin at least 1.5V above the 2V nominal bias level.
5 AGND power_in Analog ground, connected directly to the power ground.
6 RD1 passive Synchronous rectifier leading-edge delay: resistor to AGND sets the delay from the falling edge of SR1/SR2 to the rising edge of HO2/LO1 or HO1/LO2.
7 RD2 passive Synchronous rectifier trailing-edge delay: resistor to AGND sets the delay from the falling edge of HO1/LO2 or HO2/LO1 to the rising edge of SR2 or SR1.
8 RES passive Restart timer: 30µA flows into the RES capacitor on each cycle-by-cycle current limit and at 1.0V the SS capacitor is discharged to disable outputs, then 8 ramps between 2V and 4V occur before restart.
9 SS passive Soft-start input charged by an internal 20µA source; pulling it below 200mV stops PWM pulses on HO1, HO2, LO1, LO2 and turns the synchronous rectifier FETs off.
10 SSSR passive Secondary-side soft-start: external capacitor with an internal 20µA source sets the synchronous rectifier soft-start ramp, enabled when SS > 2V and ICOMP < 800µA.
11 SSOFF input Soft-stop disable: connected to AGND gives soft stop on VIN UVLO and hiccup current limit; connected to REF gives hard stop on any fault.
12 HS2 passive Switch node connection: common connection of the high-side FET source, low-side FET drain and transformer primary; absolute maximum -5V to 105V to GND.
13 HO2 output High-side PWM output driving the upper bridge MOSFET with 1.5A peak source and 2A peak sink current.
14 BST2 passive Gate-drive bootstrap: capacitor to HS2 supplies the high-side HO2 driver, with an external diode from VCC charging it when HS2 is low.
15 SR2 output Synchronous rectifier gate control output with 100mA peak source and 400mA peak sink current.
16 LO2 output Low-side PWM gate driver output with 1.5A peak source and 2A peak sink current.
17 VCC power_out Startup regulator output regulated to 9.5V initially, falling to 7.7V once SSSR reaches 1V; recommended external voltage range 10V to 14V, with the startup regulator shutting off if an auxiliary winding raises it above the setpoint.
18 PGND power_in Power ground, connected directly to the analog ground.
19 LO1 output Low-side PWM gate driver output with 1.5A peak source and 2A peak sink current.
20 SR1 output Synchronous rectifier gate control output with 100mA peak source and 400mA peak sink current.
21 BST1 passive Gate-drive bootstrap: capacitor to HS1 supplies the high-side HO1 driver, with an external diode from VCC charging it when HS1 is low.
22 HO1 output High-side PWM output driving the upper bridge MOSFET with 1.5A peak source and 2A peak sink current.
23 HS1 passive Switch node connection: common connection of the high-side FET source, low-side FET drain and transformer primary; absolute maximum -5V to 105V to GND.
24 VIN power_in Input supply to the startup regulator with operating range 14V to 100V; can be bypassed by biasing VCC externally.
25 UVLO input Line undervoltage lockout: VCC and REF regulators enable at the 0.4V threshold and the controller enters run mode at the 1.25V threshold, with 20µA hysteresis current sink.
26 OVP/OTP input Overvoltage protection input with 1.25V threshold and 20µA hysteresis current; can also be used with an NTC thermistor divider for over-temperature shutdown.
27 RAMP input PWM comparator modulation ramp input, either a primary current signal (current mode) or proportional to input voltage (feed-forward voltage mode), reset to GND each cycle.
28 CS input Current sense input that terminates the PWM pulse when above 750mV (cycle-by-cycle limit), with an internal switch holding CS low for 40ns after output turn-on for leading-edge blanking.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-28-EP(5x5)
Category Power Supply Chip
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN to GND VIN -0.3 105 V 6
HS to GND HS -5 105 V 6
BST1/BST2 to GND BST -0.3 116 V 6
BST1/BST2 to HS1/HS2 -0.3 16 V 6
VCC to GND VCC -0.3 16 V 6
REF, SSOFF, RT, OVP, UVLO to GND -0.3 7 V 6
RAMP -0.3 7 V 6
COMP input current 10 mA 6
Junction temperature TJ 150 °C 6
Storage temperature Tstg -55 150 °C 6
ESD HBM V(ESD) -2000 2000 V HBM, ANSI/ESDA/JEDEC JS-001 6
ESD CDM V(ESD) -750 750 V CDM, JESD22-C101 6
VIN voltage VIN 14 100 V 6
External voltage applied to VCC VCC 10 14 V 6
Junction temperature TJ -40 125 °C 6
SLOPE SLOPE -0.3 2 V 6
Junction-to-ambient thermal resistance RθJA 40 °C/W RSG 28-pin 6
Junction-to-case (top) thermal resistance RθJC(top) 4 °C/W RSG 28-pin 6
VCC voltage 1 VCC1 9.3 9.6 9.9 V ICC= 10 mA (SSSR < 1 V) 7
VCC voltage 2 VCC2 7.5 7.8 8.1 V ICC= 10 mA (SSSR > 1 V) 7
VCC current limit ICC(Lim) 60 80 mA VCC = 6V 7
VCC undervoltage threshold, negative-going VCC(UV) 5.9 6.3 6.7 V Negative-going VCC 7
VIN shutdown current 300 520 µA VIN = 20V, VUVLO = 0V 7
VIN shutdown current 350 550 µA VIN = 100V, VUVLO = 0V 7
REF voltage VREF 4.85 5 5.15 V IREF = 0mA 7
REF current limit IREF(Lim) 15 20 mA VREF = 4.5V 7
VREF undervoltage threshold VREFUV 4.3 4.5 4.7 V Positive-going VREF 7
UVLO threshold VUVLO 1.18 1.25 1.32 V 7
UVLO hysteresis current IUVLO 16 20 24 µA UVLO pin sink current when VUVLO < 1.25V 7
Undervoltage standby enable threshold 0.32 0.4 0.48 V UVLO voltage rising 7
OVP shutdown threshold VOVP 1.18 1.25 1.32 V OVP rising 7
OVP hysteresis current 16 20 24 µA OVP source current when OVP > 1.25V 7
SS charge current ISS 16 20 24 µA VSS = 0V 7
SS threshold for SSSR charge current enable 1.93 2 2.2 V ICOMP < 800µA 7
SSSR charge current ISSSR 16 20 24 µA VSS > 2V, ICOMP < 800µA 7
SSSR discharge current 1 ISSSR-DIS1 54 65 75 µA VUVLO < 1.25V 7
SSSR discharge current 2 ISSSR-DIS2 109 125 147 µA VRES > 1V 7
Current limit threshold VCS 0.71 0.75 0.785 V 7
CS sink impedance (clock edge) RCS 18 45 Ω Internal FET sink impedance 8
Frequency (LO1, half oscillator frequency) FSW1 185 200 215 kHz RT = 25kΩ 8
Frequency (LO1, half oscillator frequency) FSW2 420 480 540 kHz RT = 10kΩ 8
RT sync threshold 2.8 3 3.3 V 8
SR trailing edge delay T1 T1 45 65 90 ns SR off to HO&LO on, RD1 = 20kΩ 9
SR trailing edge delay T1 T1 232 300 388 ns SR off to HO&LO on, RD1 = 100kΩ 9
SR leading edge T2 T2 43 65 90 ns HO or LO off to SR on, RD2 = 20kΩ 9
SR leading edge T2 T2 227 300 384 ns HO or LO off to SR on, RD2 = 100kΩ 9
COMP current to RAMP offset voltage VPWM-OS 680 800 940 µA VRAMP = 0V 9
SS to RAMP offset voltage VSS-OS 0.78 1 1.22 V VRAMP = 0V 9
COMP current for SSSR charge current enable 690 800 915 µA VSS > 2V 9
BST undervoltage threshold VBST uv 3.8 4.7 5.6 V VBST, VHS rising 9
HO/LO low-state output voltage VOL 0.16 0.32 V IHO/LO = 100mA 9
HO/LO high-state output voltage VOH 0.27 0.495 V IHO/LO = 100mA, VOHL = VCC, VLO, VOHH = VBST, VHO 9
SR low-state output voltage VOL 0.05 0.1 V ISR1/SR2 = 10mA 9
SR high-state output voltage VOH 0.17 0.28 V ISR1/SR2 = 10mA, VOH = VREF, VSR 9
Thermal shutdown temperature TSD 160 °C 9

CAD (KiCad official)

  • Symbol: LM5045SQ
  • Footprint: Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm
  • 3D model: WQFN-28-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: lm5045sq-etched.step / lm5045sq-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5045sq.step / lm5045sq.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (47 pp, sha256 47e7c49a68c6bd8e, retrieved 2026-10-26, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF