main
Ray
Publish 0.1.0
2d3d900
LM5045SQ
Texas Instruments · AC-DC Controllers & Regulators · WQFN-28-EP(5x5)
LM5045SQ from Texas Instruments, in a WQFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SLOPE | output | Provides a 0 to 100µA ramp current source for slope compensation in current-mode control; must be grounded if slope compensation is not needed. |
| 2 | COMP | input | PWM input where an external optocoupler sinks current into an internal NPN current mirror; maximum duty cycle at zero input current and zero duty cycle at 1mA. |
| 3 | REF | power_out | 5V reference output with 15mA maximum output current; decouple locally with a 0.1µF capacitor. |
| 4 | RT/SYNC | input | Oscillator frequency set by a resistor to AGND; synchronization by AC-coupled pulses that raise the pin at least 1.5V above the 2V nominal bias level. |
| 5 | AGND | power_in | Analog ground, connected directly to the power ground. |
| 6 | RD1 | passive | Synchronous rectifier leading-edge delay: resistor to AGND sets the delay from the falling edge of SR1/SR2 to the rising edge of HO2/LO1 or HO1/LO2. |
| 7 | RD2 | passive | Synchronous rectifier trailing-edge delay: resistor to AGND sets the delay from the falling edge of HO1/LO2 or HO2/LO1 to the rising edge of SR2 or SR1. |
| 8 | RES | passive | Restart timer: 30µA flows into the RES capacitor on each cycle-by-cycle current limit and at 1.0V the SS capacitor is discharged to disable outputs, then 8 ramps between 2V and 4V occur before restart. |
| 9 | SS | passive | Soft-start input charged by an internal 20µA source; pulling it below 200mV stops PWM pulses on HO1, HO2, LO1, LO2 and turns the synchronous rectifier FETs off. |
| 10 | SSSR | passive | Secondary-side soft-start: external capacitor with an internal 20µA source sets the synchronous rectifier soft-start ramp, enabled when SS > 2V and ICOMP < 800µA. |
| 11 | SSOFF | input | Soft-stop disable: connected to AGND gives soft stop on VIN UVLO and hiccup current limit; connected to REF gives hard stop on any fault. |
| 12 | HS2 | passive | Switch node connection: common connection of the high-side FET source, low-side FET drain and transformer primary; absolute maximum -5V to 105V to GND. |
| 13 | HO2 | output | High-side PWM output driving the upper bridge MOSFET with 1.5A peak source and 2A peak sink current. |
| 14 | BST2 | passive | Gate-drive bootstrap: capacitor to HS2 supplies the high-side HO2 driver, with an external diode from VCC charging it when HS2 is low. |
| 15 | SR2 | output | Synchronous rectifier gate control output with 100mA peak source and 400mA peak sink current. |
| 16 | LO2 | output | Low-side PWM gate driver output with 1.5A peak source and 2A peak sink current. |
| 17 | VCC | power_out | Startup regulator output regulated to 9.5V initially, falling to 7.7V once SSSR reaches 1V; recommended external voltage range 10V to 14V, with the startup regulator shutting off if an auxiliary winding raises it above the setpoint. |
| 18 | PGND | power_in | Power ground, connected directly to the analog ground. |
| 19 | LO1 | output | Low-side PWM gate driver output with 1.5A peak source and 2A peak sink current. |
| 20 | SR1 | output | Synchronous rectifier gate control output with 100mA peak source and 400mA peak sink current. |
| 21 | BST1 | passive | Gate-drive bootstrap: capacitor to HS1 supplies the high-side HO1 driver, with an external diode from VCC charging it when HS1 is low. |
| 22 | HO1 | output | High-side PWM output driving the upper bridge MOSFET with 1.5A peak source and 2A peak sink current. |
| 23 | HS1 | passive | Switch node connection: common connection of the high-side FET source, low-side FET drain and transformer primary; absolute maximum -5V to 105V to GND. |
| 24 | VIN | power_in | Input supply to the startup regulator with operating range 14V to 100V; can be bypassed by biasing VCC externally. |
| 25 | UVLO | input | Line undervoltage lockout: VCC and REF regulators enable at the 0.4V threshold and the controller enters run mode at the 1.25V threshold, with 20µA hysteresis current sink. |
| 26 | OVP/OTP | input | Overvoltage protection input with 1.25V threshold and 20µA hysteresis current; can also be used with an NTC thermistor divider for over-temperature shutdown. |
| 27 | RAMP | input | PWM comparator modulation ramp input, either a primary current signal (current mode) or proportional to input voltage (feed-forward voltage mode), reset to GND each cycle. |
| 28 | CS | input | Current sense input that terminates the PWM pulse when above 750mV (cycle-by-cycle limit), with an internal switch holding CS low for 40ns after output turn-on for leading-edge blanking. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-28-EP(5x5) |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | VIN | -0.3 | 105 | V | 6 | ||
| HS to GND | HS | -5 | 105 | V | 6 | ||
| BST1/BST2 to GND | BST | -0.3 | 116 | V | 6 | ||
| BST1/BST2 to HS1/HS2 | -0.3 | 16 | V | 6 | |||
| VCC to GND | VCC | -0.3 | 16 | V | 6 | ||
| REF, SSOFF, RT, OVP, UVLO to GND | -0.3 | 7 | V | 6 | |||
| RAMP | -0.3 | 7 | V | 6 | |||
| COMP input current | 10 | mA | 6 | ||||
| Junction temperature | TJ | 150 | °C | 6 | |||
| Storage temperature | Tstg | -55 | 150 | °C | 6 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | HBM, ANSI/ESDA/JEDEC JS-001 | 6 | |
| ESD CDM | V(ESD) | -750 | 750 | V | CDM, JESD22-C101 | 6 | |
| VIN voltage | VIN | 14 | 100 | V | 6 | ||
| External voltage applied to VCC | VCC | 10 | 14 | V | 6 | ||
| Junction temperature | TJ | -40 | 125 | °C | 6 | ||
| SLOPE | SLOPE | -0.3 | 2 | V | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 40 | °C/W | RSG 28-pin | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 4 | °C/W | RSG 28-pin | 6 | ||
| VCC voltage 1 | VCC1 | 9.3 | 9.6 | 9.9 | V | ICC= 10 mA (SSSR < 1 V) | 7 |
| VCC voltage 2 | VCC2 | 7.5 | 7.8 | 8.1 | V | ICC= 10 mA (SSSR > 1 V) | 7 |
| VCC current limit | ICC(Lim) | 60 | 80 | mA | VCC = 6V | 7 | |
| VCC undervoltage threshold, negative-going | VCC(UV) | 5.9 | 6.3 | 6.7 | V | Negative-going VCC | 7 |
| VIN shutdown current | 300 | 520 | µA | VIN = 20V, VUVLO = 0V | 7 | ||
| VIN shutdown current | 350 | 550 | µA | VIN = 100V, VUVLO = 0V | 7 | ||
| REF voltage | VREF | 4.85 | 5 | 5.15 | V | IREF = 0mA | 7 |
| REF current limit | IREF(Lim) | 15 | 20 | mA | VREF = 4.5V | 7 | |
| VREF undervoltage threshold | VREFUV | 4.3 | 4.5 | 4.7 | V | Positive-going VREF | 7 |
| UVLO threshold | VUVLO | 1.18 | 1.25 | 1.32 | V | 7 | |
| UVLO hysteresis current | IUVLO | 16 | 20 | 24 | µA | UVLO pin sink current when VUVLO < 1.25V | 7 |
| Undervoltage standby enable threshold | 0.32 | 0.4 | 0.48 | V | UVLO voltage rising | 7 | |
| OVP shutdown threshold | VOVP | 1.18 | 1.25 | 1.32 | V | OVP rising | 7 |
| OVP hysteresis current | 16 | 20 | 24 | µA | OVP source current when OVP > 1.25V | 7 | |
| SS charge current | ISS | 16 | 20 | 24 | µA | VSS = 0V | 7 |
| SS threshold for SSSR charge current enable | 1.93 | 2 | 2.2 | V | ICOMP < 800µA | 7 | |
| SSSR charge current | ISSSR | 16 | 20 | 24 | µA | VSS > 2V, ICOMP < 800µA | 7 |
| SSSR discharge current 1 | ISSSR-DIS1 | 54 | 65 | 75 | µA | VUVLO < 1.25V | 7 |
| SSSR discharge current 2 | ISSSR-DIS2 | 109 | 125 | 147 | µA | VRES > 1V | 7 |
| Current limit threshold | VCS | 0.71 | 0.75 | 0.785 | V | 7 | |
| CS sink impedance (clock edge) | RCS | 18 | 45 | Ω | Internal FET sink impedance | 8 | |
| Frequency (LO1, half oscillator frequency) | FSW1 | 185 | 200 | 215 | kHz | RT = 25kΩ | 8 |
| Frequency (LO1, half oscillator frequency) | FSW2 | 420 | 480 | 540 | kHz | RT = 10kΩ | 8 |
| RT sync threshold | 2.8 | 3 | 3.3 | V | 8 | ||
| SR trailing edge delay T1 | T1 | 45 | 65 | 90 | ns | SR off to HO&LO on, RD1 = 20kΩ | 9 |
| SR trailing edge delay T1 | T1 | 232 | 300 | 388 | ns | SR off to HO&LO on, RD1 = 100kΩ | 9 |
| SR leading edge T2 | T2 | 43 | 65 | 90 | ns | HO or LO off to SR on, RD2 = 20kΩ | 9 |
| SR leading edge T2 | T2 | 227 | 300 | 384 | ns | HO or LO off to SR on, RD2 = 100kΩ | 9 |
| COMP current to RAMP offset voltage | VPWM-OS | 680 | 800 | 940 | µA | VRAMP = 0V | 9 |
| SS to RAMP offset voltage | VSS-OS | 0.78 | 1 | 1.22 | V | VRAMP = 0V | 9 |
| COMP current for SSSR charge current enable | 690 | 800 | 915 | µA | VSS > 2V | 9 | |
| BST undervoltage threshold | VBST uv | 3.8 | 4.7 | 5.6 | V | VBST, VHS rising | 9 |
| HO/LO low-state output voltage | VOL | 0.16 | 0.32 | V | IHO/LO = 100mA | 9 | |
| HO/LO high-state output voltage | VOH | 0.27 | 0.495 | V | IHO/LO = 100mA, VOHL = VCC, VLO, VOHH = VBST, VHO | 9 | |
| SR low-state output voltage | VOL | 0.05 | 0.1 | V | ISR1/SR2 = 10mA | 9 | |
| SR high-state output voltage | VOH | 0.17 | 0.28 | V | ISR1/SR2 = 10mA, VOH = VREF, VSR | 9 | |
| Thermal shutdown temperature | TSD | 160 | °C | 9 |
CAD (KiCad official)
- Symbol:
LM5045SQ - Footprint:
Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm - 3D model: WQFN-28-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
lm5045sq-etched.step/lm5045sq-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5045sq.step/lm5045sq.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (47 pp, sha256
47e7c49a68c6bd8e, retrieved 2026-10-26, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM5045SQ
**Texas Instruments** · AC-DC Controllers & Regulators · WQFN-28-EP(5x5)
LM5045SQ from Texas Instruments, in a WQFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SLOPE | output | Provides a 0 to 100µA ramp current source for slope compensation in current-mode control; must be grounded if slope compensation is not needed. |
| 2 | COMP | input | PWM input where an external optocoupler sinks current into an internal NPN current mirror; maximum duty cycle at zero input current and zero duty cycle at 1mA. |
| 3 | REF | power_out | 5V reference output with 15mA maximum output current; decouple locally with a 0.1µF capacitor. |
| 4 | RT/SYNC | input | Oscillator frequency set by a resistor to AGND; synchronization by AC-coupled pulses that raise the pin at least 1.5V above the 2V nominal bias level. |
| 5 | AGND | power_in | Analog ground, connected directly to the power ground. |
| 6 | RD1 | passive | Synchronous rectifier leading-edge delay: resistor to AGND sets the delay from the falling edge of SR1/SR2 to the rising edge of HO2/LO1 or HO1/LO2. |
| 7 | RD2 | passive | Synchronous rectifier trailing-edge delay: resistor to AGND sets the delay from the falling edge of HO1/LO2 or HO2/LO1 to the rising edge of SR2 or SR1. |
| 8 | RES | passive | Restart timer: 30µA flows into the RES capacitor on each cycle-by-cycle current limit and at 1.0V the SS capacitor is discharged to disable outputs, then 8 ramps between 2V and 4V occur before restart. |
| 9 | SS | passive | Soft-start input charged by an internal 20µA source; pulling it below 200mV stops PWM pulses on HO1, HO2, LO1, LO2 and turns the synchronous rectifier FETs off. |
| 10 | SSSR | passive | Secondary-side soft-start: external capacitor with an internal 20µA source sets the synchronous rectifier soft-start ramp, enabled when SS > 2V and ICOMP < 800µA. |
| 11 | SSOFF | input | Soft-stop disable: connected to AGND gives soft stop on VIN UVLO and hiccup current limit; connected to REF gives hard stop on any fault. |
| 12 | HS2 | passive | Switch node connection: common connection of the high-side FET source, low-side FET drain and transformer primary; absolute maximum -5V to 105V to GND. |
| 13 | HO2 | output | High-side PWM output driving the upper bridge MOSFET with 1.5A peak source and 2A peak sink current. |
| 14 | BST2 | passive | Gate-drive bootstrap: capacitor to HS2 supplies the high-side HO2 driver, with an external diode from VCC charging it when HS2 is low. |
| 15 | SR2 | output | Synchronous rectifier gate control output with 100mA peak source and 400mA peak sink current. |
| 16 | LO2 | output | Low-side PWM gate driver output with 1.5A peak source and 2A peak sink current. |
| 17 | VCC | power_out | Startup regulator output regulated to 9.5V initially, falling to 7.7V once SSSR reaches 1V; recommended external voltage range 10V to 14V, with the startup regulator shutting off if an auxiliary winding raises it above the setpoint. |
| 18 | PGND | power_in | Power ground, connected directly to the analog ground. |
| 19 | LO1 | output | Low-side PWM gate driver output with 1.5A peak source and 2A peak sink current. |
| 20 | SR1 | output | Synchronous rectifier gate control output with 100mA peak source and 400mA peak sink current. |
| 21 | BST1 | passive | Gate-drive bootstrap: capacitor to HS1 supplies the high-side HO1 driver, with an external diode from VCC charging it when HS1 is low. |
| 22 | HO1 | output | High-side PWM output driving the upper bridge MOSFET with 1.5A peak source and 2A peak sink current. |
| 23 | HS1 | passive | Switch node connection: common connection of the high-side FET source, low-side FET drain and transformer primary; absolute maximum -5V to 105V to GND. |
| 24 | VIN | power_in | Input supply to the startup regulator with operating range 14V to 100V; can be bypassed by biasing VCC externally. |
| 25 | UVLO | input | Line undervoltage lockout: VCC and REF regulators enable at the 0.4V threshold and the controller enters run mode at the 1.25V threshold, with 20µA hysteresis current sink. |
| 26 | OVP/OTP | input | Overvoltage protection input with 1.25V threshold and 20µA hysteresis current; can also be used with an NTC thermistor divider for over-temperature shutdown. |
| 27 | RAMP | input | PWM comparator modulation ramp input, either a primary current signal (current mode) or proportional to input voltage (feed-forward voltage mode), reset to GND each cycle. |
| 28 | CS | input | Current sense input that terminates the PWM pulse when above 750mV (cycle-by-cycle limit), with an internal switch holding CS low for 40ns after output turn-on for leading-edge blanking. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-28-EP(5x5) |
| Category | Power Supply Chip |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | VIN | -0.3 | | 105 | V | | 6 |
| HS to GND | HS | -5 | | 105 | V | | 6 |
| BST1/BST2 to GND | BST | -0.3 | | 116 | V | | 6 |
| BST1/BST2 to HS1/HS2 | | -0.3 | | 16 | V | | 6 |
| VCC to GND | VCC | -0.3 | | 16 | V | | 6 |
| REF, SSOFF, RT, OVP, UVLO to GND | | -0.3 | | 7 | V | | 6 |
| RAMP | | -0.3 | | 7 | V | | 6 |
| COMP input current | | | | 10 | mA | | 6 |
| Junction temperature | TJ | | | 150 | °C | | 6 |
| Storage temperature | Tstg | -55 | | 150 | °C | | 6 |
| ESD HBM | V(ESD) | -2000 | | 2000 | V | HBM, ANSI/ESDA/JEDEC JS-001 | 6 |
| ESD CDM | V(ESD) | -750 | | 750 | V | CDM, JESD22-C101 | 6 |
| VIN voltage | VIN | 14 | | 100 | V | | 6 |
| External voltage applied to VCC | VCC | 10 | | 14 | V | | 6 |
| Junction temperature | TJ | -40 | | 125 | °C | | 6 |
| SLOPE | SLOPE | -0.3 | | 2 | V | | 6 |
| Junction-to-ambient thermal resistance | RθJA | | 40 | | °C/W | RSG 28-pin | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 4 | | °C/W | RSG 28-pin | 6 |
| VCC voltage 1 | VCC1 | 9.3 | 9.6 | 9.9 | V | ICC= 10 mA (SSSR < 1 V) | 7 |
| VCC voltage 2 | VCC2 | 7.5 | 7.8 | 8.1 | V | ICC= 10 mA (SSSR > 1 V) | 7 |
| VCC current limit | ICC(Lim) | 60 | 80 | | mA | VCC = 6V | 7 |
| VCC undervoltage threshold, negative-going | VCC(UV) | 5.9 | 6.3 | 6.7 | V | Negative-going VCC | 7 |
| VIN shutdown current | | | 300 | 520 | µA | VIN = 20V, VUVLO = 0V | 7 |
| VIN shutdown current | | | 350 | 550 | µA | VIN = 100V, VUVLO = 0V | 7 |
| REF voltage | VREF | 4.85 | 5 | 5.15 | V | IREF = 0mA | 7 |
| REF current limit | IREF(Lim) | 15 | 20 | | mA | VREF = 4.5V | 7 |
| VREF undervoltage threshold | VREFUV | 4.3 | 4.5 | 4.7 | V | Positive-going VREF | 7 |
| UVLO threshold | VUVLO | 1.18 | 1.25 | 1.32 | V | | 7 |
| UVLO hysteresis current | IUVLO | 16 | 20 | 24 | µA | UVLO pin sink current when VUVLO < 1.25V | 7 |
| Undervoltage standby enable threshold | | 0.32 | 0.4 | 0.48 | V | UVLO voltage rising | 7 |
| OVP shutdown threshold | VOVP | 1.18 | 1.25 | 1.32 | V | OVP rising | 7 |
| OVP hysteresis current | | 16 | 20 | 24 | µA | OVP source current when OVP > 1.25V | 7 |
| SS charge current | ISS | 16 | 20 | 24 | µA | VSS = 0V | 7 |
| SS threshold for SSSR charge current enable | | 1.93 | 2 | 2.2 | V | ICOMP < 800µA | 7 |
| SSSR charge current | ISSSR | 16 | 20 | 24 | µA | VSS > 2V, ICOMP < 800µA | 7 |
| SSSR discharge current 1 | ISSSR-DIS1 | 54 | 65 | 75 | µA | VUVLO < 1.25V | 7 |
| SSSR discharge current 2 | ISSSR-DIS2 | 109 | 125 | 147 | µA | VRES > 1V | 7 |
| Current limit threshold | VCS | 0.71 | 0.75 | 0.785 | V | | 7 |
| CS sink impedance (clock edge) | RCS | | 18 | 45 | Ω | Internal FET sink impedance | 8 |
| Frequency (LO1, half oscillator frequency) | FSW1 | 185 | 200 | 215 | kHz | RT = 25kΩ | 8 |
| Frequency (LO1, half oscillator frequency) | FSW2 | 420 | 480 | 540 | kHz | RT = 10kΩ | 8 |
| RT sync threshold | | 2.8 | 3 | 3.3 | V | | 8 |
| SR trailing edge delay T1 | T1 | 45 | 65 | 90 | ns | SR off to HO&LO on, RD1 = 20kΩ | 9 |
| SR trailing edge delay T1 | T1 | 232 | 300 | 388 | ns | SR off to HO&LO on, RD1 = 100kΩ | 9 |
| SR leading edge T2 | T2 | 43 | 65 | 90 | ns | HO or LO off to SR on, RD2 = 20kΩ | 9 |
| SR leading edge T2 | T2 | 227 | 300 | 384 | ns | HO or LO off to SR on, RD2 = 100kΩ | 9 |
| COMP current to RAMP offset voltage | VPWM-OS | 680 | 800 | 940 | µA | VRAMP = 0V | 9 |
| SS to RAMP offset voltage | VSS-OS | 0.78 | 1 | 1.22 | V | VRAMP = 0V | 9 |
| COMP current for SSSR charge current enable | | 690 | 800 | 915 | µA | VSS > 2V | 9 |
| BST undervoltage threshold | VBST uv | 3.8 | 4.7 | 5.6 | V | VBST, VHS rising | 9 |
| HO/LO low-state output voltage | VOL | | 0.16 | 0.32 | V | IHO/LO = 100mA | 9 |
| HO/LO high-state output voltage | VOH | | 0.27 | 0.495 | V | IHO/LO = 100mA, VOHL = VCC, VLO, VOHH = VBST, VHO | 9 |
| SR low-state output voltage | VOL | | 0.05 | 0.1 | V | ISR1/SR2 = 10mA | 9 |
| SR high-state output voltage | VOH | | 0.17 | 0.28 | V | ISR1/SR2 = 10mA, VOH = VREF, VSR | 9 |
| Thermal shutdown temperature | TSD | | 160 | | °C | | 9 |
## CAD (KiCad official)
- Symbol: `LM5045SQ`
- Footprint: `Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm`
- 3D model: WQFN-28-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `lm5045sq-etched.step` / `lm5045sq-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5045sq.step` / `lm5045sq.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5045) (47 pp, sha256 `47e7c49a68c6bd8e`, retrieved 2026-10-26, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm5045sq-datasheet.pdf)