main
Ray lm25122qpwprq1: specified limits as data (metadata.characteristics, 60 rows from the datasheet) aaa5ab9

LM25122QPWPRQ1

Texas Instruments · DC-DC Controllers · HTSSOP-20-EP

LM25122QPWPRQ1 from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNCOUT output Clock output pin providing 180° phase-shifted clock output for interleaved multi-phase operation; can be left floating when not used.
2 OPT input Clock synchronization selection pin for master/slave configuration; internal pullup/pulldown held at 0.15V default; must not be left floating.
3 CSN input Inverting input of current sense amplifier; connect to the negative-side of the current sense resistor with common-mode range 3V to 42V.
4 CSP input Non-inverting input of current sense amplifier with 10 V/V gain; connect to positive-side of current sense resistor with common-mode range 3V to 42V.
5 VIN power_in Supply voltage input source for VCC regulator; connect to input capacitor and source with short, low-impedance paths; operating range 4.5V to 42V at startup, minimum 3V after startup.
6 UVLO input Undervoltage lockout programming pin; voltage below 0.4V causes shutdown, 0.4V to 1.2V causes standby with VCC regulator operational, above 1.2V enables startup; maximum voltage 15V.
7 SS input Soft-start programming pin; external capacitor with internal 10-μA current source sets output voltage ramp rate during soft-start sequence from input to target voltage.
8 SYNCIN/RT input Internal oscillator frequency programming pin; resistor to AGND sets switching frequency up to 600 kHz maximum or accepts external clock synchronization pulses up to 1.2 MHz.
9 AGND power_in Analog ground connection serving as return path for internal voltage reference, error amplifier, and all analog circuits.
10 FB input Feedback inverting input of internal error amplifier with 1.2V regulation threshold; FB voltage above 2.7V at initial power-on configures slave mode operation.
11 COMP output Output of internal error amplifier (DC gain 80 dB, bandwidth 3 MHz); connect Type 2 feedback compensation network between this pin and FB pin.
12 SLOPE input Slope compensation resistor connection pin; single resistor between SLOPE and AGND programs amplitude for stability above 50% duty cycle; cannot be left floating.
13 MODE input Switching mode selection pin with 700-kΩ internal pullup and 100-kΩ pulldown held to 0.15V default; voltage above 1.2V enables forced PWM mode, below 1.2V enables diode emulation mode.
14 RES output Restart timer external capacitor connection pin for configuring hiccup mode off-time and restart delay during overload conditions; connect to AGND when hiccup mode not required.
15 PGND power_in Power ground connection pin for low-side N-channel MOSFET gate driver; must connect directly to source terminal of low-side NMOS switch.
16 LO output Low-side N-channel MOSFET gate drive output with 3A sink/source capability; connect to gate through short, low-inductance path with forced off-time 330-750 ns.
17 VCC power_out VCC bias supply pin providing internal regulated 7.6V for controller and gate drivers; decouple to PGND with 1-47 μF low-ESR capacitor placed close to device; can accept 9-14.5V external supply through blocking diode.
18 SW bidirectional Switching node of boost regulator connecting bootstrap capacitor, high-side NMOS source, and low-side NMOS drain; maximum voltage 60V with typical swing 0V to output voltage.
19 HO output High-side N-channel MOSFET gate drive output with 3A sink/source capability and 100% duty cycle capacity via internal charge pump; connect to high-side gate through short, low-inductance path.
20 BST power_out Bootstrap supply voltage for high-side gate driver connected to bootstrap diode cathode; internal charge pump sources 200-μA current to bootstrap capacitor for full high-side drive capability.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-20-EP
Category Power Supply Chip
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input VIN, CSP, CSN -0.3 50 V 4
BST to SW, FB, MODE, UVLO, OPT, VCC -0.3 15 V 4
SW -5 60 V 4
BST -0.3 75 V 4
SS, SLOPE, SYNCIN/RT -0.3 7 V 4
CSP to CSN, PGND -0.3 0.3 V 4
HO to SW -0.3 V 4
LO -0.3 V 4
COMP, RES, SYNCOUT -0.3 7 V 4
Thermal Junction Temperature -40 150 ºC 4
Storage temperature Tstg -55 150 °C 4
Input supply voltage VIN 4.5 42 V 5
Low-side driver bias voltage VCC 14 V 5
High-side driver bias voltage BST to SW 3.8 14 V 5
Current sense common mode range CSP, CSN 3 42 V 5
Switch node voltage SW 50 V 5
Junction temperature TJ -40 125 ºC 5
VIN shutdown current ISHUTDOWN 9 17 µA VUVLO = 0 V 6
VIN operating current (exclude the current into RT resistor) IBIAS 4 5 mA VUVLO = 2 V, non-switching 6
VCC regulation VCC(REG) 6.9 7.6 8.3 V No load 6
VCC dropout (VIN to VCC) 0.28 0.5 V VVIN = 4.5 V, IVCC = 25 mA 6
VCC sourcing current limit 50 62 mA VVCC = 0 V 6
VCC operating current (exclude the current into RT resistor) IVCC 3.5 5 mA VVCC = 8.3 V 6
VCC undervoltage threshold 3.9 4 4.1 V VCC rising, VVIN = 4.5 V 6
UVLO threshold 1.17 1.2 1.23 V UVLO rising 6
UVLO hysteresis current 7 10 13 µA VUVLO = 1.4 V 6
UVLO standby enable threshold 0.3 0.4 0.5 V UVLO rising 6
Diode emulation mode threshold 1.2 1.24 1.28 V MODE rising 6
Default MODE voltage 145 155 170 mV 6
FB reference voltage VREF 1.188 1.2 1.212 V Measured at FB, VFB= VCOMP 6
Slave mode threshold 2.7 3.4 V FB rising 6
SLOPE output voltage 1.17 1.2 1.23 V 7
Slope compensation amplitude VSLOPE 1.375 1.65 1.925 V RSLOPE = 20 kΩ, fSW = 100 kHz, 50% duty cycle, TJ = –40ºC to +125ºC 7
SS current source ISS-SOURCE 7.5 10 12 µA VSS = 0 V 7
Forced LO off-time tLO-OFF 330 400 ns VVCC = 5.5 V 7
Forced LO off-time tLO-OFF 560 750 ns VVCC = 4.5 V 7
COMP to PWM voltage drop 0.95 1.1 1.25 V TJ = –40ºC to +125ºC 7
Cycle-by-cycle current limit threshold VCS-TH1 65.5 75 87.5 mV CSP to CSN, TJ = –40ºC to +125ºC 7
Cycle-by-cycle current limit threshold VCS-TH1 67 75 86 mV CSP to CSN, TJ = 25ºC 7
Zero cross detection threshold VCS-ZCD 0.5 6 12 mV CSP to CSN, falling 7
Bias current matching ICSP - ICSN -1.75 1 3.75 µA 7
VRES restart threshold VRES 1.15 1.2 1.25 V RES rising 7
RES current source1 IRES-SOURCE1 20 30 40 µA Fault-state charging current 7
HO high-state voltage drop VOHH 0.15 0.24 V IHO = –100 mA, VOHH = VBST –VHO 8
HO low-state voltage drop VOLH 0.1 0.18 V IHO = 100 mA, VOLH = VHO –VSW 8
BST charge pump sourcing current IBST 100 200 µA VVIN = VSW = 9.0 V, VBST - VSW = 5.0 V 8
BST charge pump regulation 5.3 6.2 6.75 V BST to SW, IBST= –70 μA, VVIN = VSW = 9.0 V 8
BST charge pump regulation 7 8.5 9 V BST to SW, IBST = –70 μA, VVIN = VSW = 12 V 8
BST to SW undervoltage 2 3 3.5 V 8
BST DC bias current 30 45 µA VBST - VSW = 12 V, VSW = 0 V 8
LO high-state voltage drop VOHL 0.15 0.25 V ILO = –100 mA, VOHL = VVCC –VLO 8
LO low-state voltage drop VOLL 0.1 0.17 V ILO = 100 mA, VOLL = VLO 8
LO fall to HO rise delay tDLH 50 80 115 ns No load, 50% to 50% 8
HO fall to LO rise delay tDHL 60 80 105 ns No load, 50% to 50% 8
Junction-to-ambient thermal resistance RθJA 36 ºC/W 5
Junction-to-case (top) thermal resistance RθJC(top) 20.1 ºC/W 5
Junction-to-board thermal resistance RθJB 16.8 ºC/W 5
Junction-to-top characterization parameter ψJT 0.4 ºC/W 5
Junction-to-board characterization parameter ψJB 16.7 ºC/W 5
Junction-to-case (bottom) thermal resistance ψJCbot 1.7 ºC/W 5

CAD (KiCad official)

  • Symbol: LM25122QPWPRQ1
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: lm25122qpwprq1-etched.step / lm25122qpwprq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm25122qpwprq1.step / lm25122qpwprq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (49 pp, sha256 958379e72596a27b, retrieved 2026-10-01, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF