Generated by kicad-footprint-generator · KiCad file format 20260206
LM25122QPWPRQ1
Texas Instruments · DC-DC Controllers · HTSSOP-20-EP
LM25122QPWPRQ1 from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNCOUT | output | Clock output pin providing 180° phase-shifted clock output for interleaved multi-phase operation; can be left floating when not used. |
| 2 | OPT | input | Clock synchronization selection pin for master/slave configuration; internal pullup/pulldown held at 0.15V default; must not be left floating. |
| 3 | CSN | input | Inverting input of current sense amplifier; connect to the negative-side of the current sense resistor with common-mode range 3V to 42V. |
| 4 | CSP | input | Non-inverting input of current sense amplifier with 10 V/V gain; connect to positive-side of current sense resistor with common-mode range 3V to 42V. |
| 5 | VIN | power_in | Supply voltage input source for VCC regulator; connect to input capacitor and source with short, low-impedance paths; operating range 4.5V to 42V at startup, minimum 3V after startup. |
| 6 | UVLO | input | Undervoltage lockout programming pin; voltage below 0.4V causes shutdown, 0.4V to 1.2V causes standby with VCC regulator operational, above 1.2V enables startup; maximum voltage 15V. |
| 7 | SS | input | Soft-start programming pin; external capacitor with internal 10-μA current source sets output voltage ramp rate during soft-start sequence from input to target voltage. |
| 8 | SYNCIN/RT | input | Internal oscillator frequency programming pin; resistor to AGND sets switching frequency up to 600 kHz maximum or accepts external clock synchronization pulses up to 1.2 MHz. |
| 9 | AGND | power_in | Analog ground connection serving as return path for internal voltage reference, error amplifier, and all analog circuits. |
| 10 | FB | input | Feedback inverting input of internal error amplifier with 1.2V regulation threshold; FB voltage above 2.7V at initial power-on configures slave mode operation. |
| 11 | COMP | output | Output of internal error amplifier (DC gain 80 dB, bandwidth 3 MHz); connect Type 2 feedback compensation network between this pin and FB pin. |
| 12 | SLOPE | input | Slope compensation resistor connection pin; single resistor between SLOPE and AGND programs amplitude for stability above 50% duty cycle; cannot be left floating. |
| 13 | MODE | input | Switching mode selection pin with 700-kΩ internal pullup and 100-kΩ pulldown held to 0.15V default; voltage above 1.2V enables forced PWM mode, below 1.2V enables diode emulation mode. |
| 14 | RES | output | Restart timer external capacitor connection pin for configuring hiccup mode off-time and restart delay during overload conditions; connect to AGND when hiccup mode not required. |
| 15 | PGND | power_in | Power ground connection pin for low-side N-channel MOSFET gate driver; must connect directly to source terminal of low-side NMOS switch. |
| 16 | LO | output | Low-side N-channel MOSFET gate drive output with 3A sink/source capability; connect to gate through short, low-inductance path with forced off-time 330-750 ns. |
| 17 | VCC | power_out | VCC bias supply pin providing internal regulated 7.6V for controller and gate drivers; decouple to PGND with 1-47 μF low-ESR capacitor placed close to device; can accept 9-14.5V external supply through blocking diode. |
| 18 | SW | bidirectional | Switching node of boost regulator connecting bootstrap capacitor, high-side NMOS source, and low-side NMOS drain; maximum voltage 60V with typical swing 0V to output voltage. |
| 19 | HO | output | High-side N-channel MOSFET gate drive output with 3A sink/source capability and 100% duty cycle capacity via internal charge pump; connect to high-side gate through short, low-inductance path. |
| 20 | BST | power_out | Bootstrap supply voltage for high-side gate driver connected to bootstrap diode cathode; internal charge pump sources 200-μA current to bootstrap capacitor for full high-side drive capability. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input VIN, CSP, CSN | -0.3 | 50 | V | 4 | |||
| BST to SW, FB, MODE, UVLO, OPT, VCC | -0.3 | 15 | V | 4 | |||
| SW | -5 | 60 | V | 4 | |||
| BST | -0.3 | 75 | V | 4 | |||
| SS, SLOPE, SYNCIN/RT | -0.3 | 7 | V | 4 | |||
| CSP to CSN, PGND | -0.3 | 0.3 | V | 4 | |||
| HO to SW | -0.3 | V | 4 | ||||
| LO | -0.3 | V | 4 | ||||
| COMP, RES, SYNCOUT | -0.3 | 7 | V | 4 | |||
| Thermal Junction Temperature | -40 | 150 | ºC | 4 | |||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| Input supply voltage | VIN | 4.5 | 42 | V | 5 | ||
| Low-side driver bias voltage | VCC | 14 | V | 5 | |||
| High-side driver bias voltage | BST to SW | 3.8 | 14 | V | 5 | ||
| Current sense common mode range CSP, CSN | 3 | 42 | V | 5 | |||
| Switch node voltage | SW | 50 | V | 5 | |||
| Junction temperature | TJ | -40 | 125 | ºC | 5 | ||
| VIN shutdown current | ISHUTDOWN | 9 | 17 | µA | VUVLO = 0 V | 6 | |
| VIN operating current (exclude the current into RT resistor) | IBIAS | 4 | 5 | mA | VUVLO = 2 V, non-switching | 6 | |
| VCC regulation | VCC(REG) | 6.9 | 7.6 | 8.3 | V | No load | 6 |
| VCC dropout (VIN to VCC) | 0.28 | 0.5 | V | VVIN = 4.5 V, IVCC = 25 mA | 6 | ||
| VCC sourcing current limit | 50 | 62 | mA | VVCC = 0 V | 6 | ||
| VCC operating current (exclude the current into RT resistor) | IVCC | 3.5 | 5 | mA | VVCC = 8.3 V | 6 | |
| VCC undervoltage threshold | 3.9 | 4 | 4.1 | V | VCC rising, VVIN = 4.5 V | 6 | |
| UVLO threshold | 1.17 | 1.2 | 1.23 | V | UVLO rising | 6 | |
| UVLO hysteresis current | 7 | 10 | 13 | µA | VUVLO = 1.4 V | 6 | |
| UVLO standby enable threshold | 0.3 | 0.4 | 0.5 | V | UVLO rising | 6 | |
| Diode emulation mode threshold | 1.2 | 1.24 | 1.28 | V | MODE rising | 6 | |
| Default MODE voltage | 145 | 155 | 170 | mV | 6 | ||
| FB reference voltage | VREF | 1.188 | 1.2 | 1.212 | V | Measured at FB, VFB= VCOMP | 6 |
| Slave mode threshold | 2.7 | 3.4 | V | FB rising | 6 | ||
| SLOPE output voltage | 1.17 | 1.2 | 1.23 | V | 7 | ||
| Slope compensation amplitude | VSLOPE | 1.375 | 1.65 | 1.925 | V | RSLOPE = 20 kΩ, fSW = 100 kHz, 50% duty cycle, TJ = –40ºC to +125ºC | 7 |
| SS current source | ISS-SOURCE | 7.5 | 10 | 12 | µA | VSS = 0 V | 7 |
| Forced LO off-time | tLO-OFF | 330 | 400 | ns | VVCC = 5.5 V | 7 | |
| Forced LO off-time | tLO-OFF | 560 | 750 | ns | VVCC = 4.5 V | 7 | |
| COMP to PWM voltage drop | 0.95 | 1.1 | 1.25 | V | TJ = –40ºC to +125ºC | 7 | |
| Cycle-by-cycle current limit threshold | VCS-TH1 | 65.5 | 75 | 87.5 | mV | CSP to CSN, TJ = –40ºC to +125ºC | 7 |
| Cycle-by-cycle current limit threshold | VCS-TH1 | 67 | 75 | 86 | mV | CSP to CSN, TJ = 25ºC | 7 |
| Zero cross detection threshold | VCS-ZCD | 0.5 | 6 | 12 | mV | CSP to CSN, falling | 7 |
| Bias current matching ICSP - ICSN | -1.75 | 1 | 3.75 | µA | 7 | ||
| VRES restart threshold | VRES | 1.15 | 1.2 | 1.25 | V | RES rising | 7 |
| RES current source1 | IRES-SOURCE1 | 20 | 30 | 40 | µA | Fault-state charging current | 7 |
| HO high-state voltage drop | VOHH | 0.15 | 0.24 | V | IHO = –100 mA, VOHH = VBST –VHO | 8 | |
| HO low-state voltage drop | VOLH | 0.1 | 0.18 | V | IHO = 100 mA, VOLH = VHO –VSW | 8 | |
| BST charge pump sourcing current | IBST | 100 | 200 | µA | VVIN = VSW = 9.0 V, VBST - VSW = 5.0 V | 8 | |
| BST charge pump regulation | 5.3 | 6.2 | 6.75 | V | BST to SW, IBST= –70 μA, VVIN = VSW = 9.0 V | 8 | |
| BST charge pump regulation | 7 | 8.5 | 9 | V | BST to SW, IBST = –70 μA, VVIN = VSW = 12 V | 8 | |
| BST to SW undervoltage | 2 | 3 | 3.5 | V | 8 | ||
| BST DC bias current | 30 | 45 | µA | VBST - VSW = 12 V, VSW = 0 V | 8 | ||
| LO high-state voltage drop | VOHL | 0.15 | 0.25 | V | ILO = –100 mA, VOHL = VVCC –VLO | 8 | |
| LO low-state voltage drop | VOLL | 0.1 | 0.17 | V | ILO = 100 mA, VOLL = VLO | 8 | |
| LO fall to HO rise delay | tDLH | 50 | 80 | 115 | ns | No load, 50% to 50% | 8 |
| HO fall to LO rise delay | tDHL | 60 | 80 | 105 | ns | No load, 50% to 50% | 8 |
| Junction-to-ambient thermal resistance | RθJA | 36 | ºC/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 20.1 | ºC/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 16.8 | ºC/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 0.4 | ºC/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 16.7 | ºC/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | ψJCbot | 1.7 | ºC/W | 5 |
CAD (KiCad official)
- Symbol:
LM25122QPWPRQ1 - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
lm25122qpwprq1-etched.step/lm25122qpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm25122qpwprq1.step/lm25122qpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (49 pp, sha256
958379e72596a27b, retrieved 2026-10-01, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).