main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs l6470htr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers l6470htr: viewers · Ray
l6470htr-etched.fit.json l6470htr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
l6470htr-etched.glb l6470htr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
l6470htr-etched.step l6470htr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
l6470htr.glb Publish 0.1.0 · Ray
l6470htr.kicad_mod Publish 0.1.0 · Ray
l6470htr.kicad_sym Publish 0.1.0 · Ray
l6470htr.lbr Publish 0.1.0 · Ray
l6470htr.step Publish 0.1.0 · Ray
package.json l6470htr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json l6470htr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/l6470htr · Ray

L6470HTR

STMicroelectronics · Stepper Motor Driver · HTSSOP-28

L6470HTR from STMicroelectronics, in a HTSSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT1A power_out Full bridge A phase output 1 capable of sourcing or sinking up to 7 A peak current with programmable slew rate control.
2 VSA power_in Full bridge A power supply input pin requiring 8-45 V supply voltage and must be connected to VSB.
3 STBY\RST input Active-low standby and reset pin that resets logic and disables charge pump when driven low; must be connected to VDD if not used.
4 SW input External switch input pin with internal 60-110 kΩ pull-up resistor for user-defined interrupt control; must be connected to VDD if not used.
5 ADCIN input Integrated analog-to-digital converter input pin accepting 0-VREG voltage range with 5-bit resolution sampled at PWM frequency.
6 VREG power_in Internal 3 V voltage regulator output and external 3.3 V logic supply pin capable of sourcing 40 mA with 50 mV maximum dropout; requires 22-47 µF bypass capacitor.
7 OSCIN input Oscillator input pin for connecting external crystal/resonator (8-32 MHz) or direct clock source; leave floating if using internal oscillator.
8 OSCOUT output Oscillator output pin providing 2/4/8/16 MHz clock from internal oscillator or crystal/resonator driving capability with 4 mA maximum output current.
9 AGND power_in Analog ground reference pin internally connected to PGND and DGND; differential voltage between AGND and DGND must not exceed ±0.3 V.
10 CP output Charge pump oscillator output pin supplying signal for external charge pump circuit with 660-800 kHz oscillation frequency.
11 VBOOT power_in Bootstrap voltage supply pin (maximum 55 V) for high-side gate drivers requiring 1.1-1.4 mA average charging current.
12 VSB power_in Full bridge B power supply input pin requiring 8-45 V supply voltage and must be connected to VSA.
13 PGND power_in Power ground reference pin for motor output stage; differential voltage between PGND and DGND must not exceed ±0.3 V.
14 OUT1B power_out Full bridge B phase output 1 capable of sourcing or sinking up to 7 A peak current with programmable slew rate control.
15 OUT2B power_out Full bridge B phase output 2 capable of sourcing or sinking up to 7 A peak current with programmable slew rate control.
16 VSB power_in Full bridge B power supply input pin requiring 8-45 V supply voltage and must be connected to VSA; duplicate connection for current distribution.
17 VDD power_in Logic power supply voltage (3.3 V or 5 V) for output driver pull-up reference; requires 10 µF bypass capacitor for proper operation.
18 SDO output SPI serial data output pin with 0.3 V maximum low voltage and 2.4 V minimum high voltage at 3.3 V VDD; maximum drive current 4 mA.
19 CK input SPI serial clock input pin (TTL/CMOS compatible, 3.3-5 V logic levels) with maximum frequency 5 MHz and 0.8-2 V logic thresholds.
20 SDI input SPI serial data input pin (TTL/CMOS compatible, 3.3-5 V logic levels) sampled on CK rising edges with 25 ns setup and 20 ns hold time.
21 DGND power_in Digital ground reference pin for logic circuitry; differential voltage between DGND and AGND must not exceed ±0.3 V.
22 BUSY\SYNC tri_state Open-drain output pin functioning as busy flag (pulled low during command execution) or synchronization clock signal based on SYNC_EN bit.
23 CS input SPI chip select input pin (active low, TTL/CMOS compatible) with 335-565 kΩ internal pull-up resistance and 350 ns setup time.
24 FLAG tri_state Open-drain output pin (active low) for alarm condition signaling on overcurrent, thermal shutdown/warning, UVLO, stall detection, switch events, or command errors.
25 STCK input Step-clock input pin (TTL/CMOS compatible, 3.3-5 V logic levels) for external pulse counting mode with maximum input frequency 2 MHz.
26 VSA power_in Full bridge A power supply input pin requiring 8-45 V supply voltage and must be connected to VSB; duplicate connection for current distribution.
27 PGND power_in Power ground reference pin for motor output stage; differential voltage between PGND and DGND must not exceed ±0.3 V; duplicate connection for current distribution.
28 OUT2A power_out Full bridge A phase output 2 capable of sourcing or sinking up to 7 A peak current with programmable slew rate control.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package HTSSOP-28
Category Motor Driver ICs
Pins 29

CAD (KiCad official)

  • Symbol: L6470HTR
  • Footprint: Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm
  • 3D model: HTSSOP-28 (KiCad packages3D, STEP)
  • 3D model files: l6470htr-etched.step / l6470htr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l6470htr.step / l6470htr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (73 pp, sha256 4b94ab59eec71372, retrieved 2026-09-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF