Generated by kicad-footprint-generator · KiCad file format 20260206
KSZ8091MNXCA
Microchip Tech · Ethernet ICs · QFN-32-EP(5x5)
KSZ8091MNXCA from Microchip Tech, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin for the device. |
| 2 | VDD_1.2 | power_out | 1.2V core VDD supplied by the internal regulator; decouple with 2.2 μF and 0.1 μF capacitors to ground. |
| 3 | VDDA_3.3 | power_in | 3.3V analog VDD; connect to the board 3.3V supply through a ferrite bead and decouple with 22 μF and 0.1 μF capacitors to ground. |
| 4 | RXM | bidirectional | Physical receive or transmit signal, negative differential pair. |
| 5 | RXP | bidirectional | Physical receive or transmit signal, positive differential pair. |
| 6 | TXM | bidirectional | Physical transmit or receive signal, negative differential pair. |
| 7 | TXP | bidirectional | Physical transmit or receive signal, positive differential pair. |
| 8 | XO | output | Crystal feedback for the 25 MHz crystal; no connect if an oscillator or external clock source is used. |
| 9 | XI | input | Crystal, oscillator or external clock input at 25 MHz ±50 ppm. |
| 10 | REXT | input | Sets the PHY transmit output current; connect a 6.49 kΩ resistor to ground on this pin. |
| 11 | MDIO | bidirectional | MII management data I/O with a weak pull-up, open-drain output, and a required external 1.0 kΩ pull-up resistor. |
| 12 | MDC | input | MII management clock input, synchronous to the MDIO data pin. |
| 13 | RXD3/PHYAD0 | bidirectional | MII receive data output bit 3; in config mode the pull-up/pull-down is latched as PHYADDR[0] at reset de-assertion. |
| 14 | RXD2/PHYAD1 | bidirectional | MII receive data output bit 2; in config mode the pull-up/pull-down is latched as PHYADDR[1] at reset de-assertion. |
| 15 | RXD1/PHYAD2 | bidirectional | MII receive data output bit 1; in config mode the pull-up/pull-down is latched as PHYADDR[2] at reset de-assertion. |
| 16 | RXD0/DUPLEX | bidirectional | MII receive data output bit 0; in config mode the pull-up/pull-down is latched as DUPLEX at reset de-assertion. |
| 17 | VDDIO | power_in | 3.3V, 2.5V, or 1.8V digital VDD; decouple with 22 μF and 0.1 μF capacitors to ground. |
| 18 | RXDV/CONFIG2 | bidirectional | MII receive data valid output; in config mode it is latched as CONFIG2 at reset de-assertion. |
| 19 | RXC/B-CAST_OFF | bidirectional | MII receive clock output; in config mode it is latched as B-CAST_OFF at reset de-assertion. |
| 20 | RXER/ISO | bidirectional | MII receive error output; in config mode it is latched as ISOLATE at reset de-assertion. |
| 21 | INTRP/PME_N2/NAND_Tree# | bidirectional | Programmable interrupt output, active low by default, with a weak pull-up, open-drain output, and a required 1.0 kΩ pull-up to VDDIO for interrupt and PME functions. |
| 22 | TXC/PME_EN | bidirectional | MII transmit clock output; no connection in MII back-to-back mode, and latched as PME_EN in config mode. |
| 23 | TXEN | input | MII transmit enable input. |
| 24 | TXD0 | input | MII transmit data input bit 0, synchronous to TXC. |
| 25 | TXD1 | input | MII transmit data input bit 1, synchronous to TXC. |
| 26 | TXD2 | input | MII transmit data input bit 2, synchronous to TXC. |
| 27 | TXD3 | input | MII transmit data input bit 3, synchronous to TXC. |
| 28 | COL/CONFIG0 | bidirectional | MII collision detect output; in config mode it is latched as CONFIG0 at reset de-assertion. |
| 29 | CRS/CONFIG1 | bidirectional | MII carrier sense output; in config mode it is latched as CONFIG1 at reset de-assertion and serves as the NAND tree output. |
| 30 | LED0/PME_N1/NWAYEN | bidirectional | Programmable LED0 output; in config mode it is latched as auto-negotiation enable at reset de-assertion, and can serve as an open-drain PME_N output needing a 1.0 kΩ pull-up to VDDIO. |
| 31 | TXER | input | MII transmit error input; must be pulled high by a pull-up resistor for NAND tree testing. |
| 32 | RST# | input | Chip reset, active low, with an internal weak pull-up. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-32-EP(5x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VDD_1.2) | VIN | -0.5 | 1.8 | V | 57 | ||
| Supply Voltage (VDDIO, VDDA_3.3) | VIN | -0.5 | 5 | V | 57 | ||
| Input Voltage (all inputs) | -0.5 | 5 | V | 57 | |||
| Output Voltage (all outputs) | -0.5 | 5 | V | 57 | |||
| Lead Temperature | 260 | °C | soldering, 10s | 57 | |||
| Storage Temperature | TS | -55 | 150 | °C | 57 | ||
| Supply Voltage (VDDIO_3.3, VDDA_3.3) | 3.135 | 3.465 | V | 57 | |||
| Supply Voltage (VDDIO_2.5) | 2.375 | 2.625 | V | 57 | |||
| Supply Voltage (VDDIO_1.8) | 1.71 | 1.89 | V | 57 | |||
| Ambient Temperature (TA Commercial) | TA | 0 | 70 | °C | TA Commercial grade | 57 | |
| Ambient Temperature (TA Industrial) | TA | -40 | 85 | °C | TA Industrial grade | 57 | |
| Maximum Junction Temperature | TJ | 125 | °C | 57 | |||
| Input High Voltage | VIH | 2 | V | VDDIO = 3.3V | 58 | ||
| Input High Voltage | VIH | 1.8 | V | VDDIO = 2.5V | 58 | ||
| Input High Voltage | VIH | 1.3 | V | VDDIO = 1.8V | 58 | ||
| Input Low Voltage | VIL | 0.8 | V | VDDIO = 3.3V | 58 | ||
| Input Low Voltage | VIL | 0.7 | V | VDDIO = 2.5V | 58 | ||
| Input Low Voltage | VIL | 0.5 | V | VDDIO = 1.8V | 58 | ||
| Input Current | /IIN/ | 10 | μA | VIN = GND ~ VDDIO | 58 | ||
| Output High Voltage | VOH | 2.4 | V | VDDIO = 3.3V | 58 | ||
| Output High Voltage | VOH | 2 | V | VDDIO = 2.5V | 58 | ||
| Output High Voltage | VOH | 1.5 | V | VDDIO = 1.8V | 58 | ||
| Output Low Voltage | VOL | 0.4 | V | VDDIO = 3.3V | 58 | ||
| Output Low Voltage | VOL | 0.3 | V | VDDIO = 1.8V | 58 | ||
| Output Tri-State Leakage | /IOZ/ | 10 | μA | 58 | |||
| Internal Pull-Up Resistance | pu | 30 | 45 | 73 | kΩ | VDDIO = 3.3V | 58 |
| Internal Pull-Up Resistance | pu | 39 | 61 | 102 | kΩ | VDDIO = 2.5V | 58 |
| Internal Pull-Up Resistance | pu | 48 | 99 | 178 | kΩ | VDDIO = 1.8V | 58 |
| Internal Pull-Down Resistance | pd | 26 | 43 | 79 | kΩ | VDDIO = 3.3V | 58 |
| Internal Pull-Down Resistance | pd | 34 | 59 | 113 | kΩ | VDDIO = 2.5V | 58 |
| Internal Pull-Down Resistance | pd | 53 | 99 | 200 | kΩ | VDDIO = 1.8V | 58 |
| Peak Differential Output Voltage (100BASE-TX) | VO | 0.95 | 1.05 | V | 100Ω termination across differential output | 58 | |
| Output Voltage Imbalance | VIMB | 2 | % | 100Ω termination across differential output | 58 | ||
| Rise/Fall Time (100BASE-TX) | tr/tf | 3 | 5 | ns | 58 | ||
| Duty Cycle Distortion | -0.25 | 0.25 | ns | 58 | |||
| Overshoot | 5 | % | 58 | ||||
| Peak Differential Output Voltage (10BASE-T) | VP | 2.2 | 2.8 | V | 100Ω termination across differential output | 59 | |
| Jitter Added (10BASE-T) | 3.5 | ns | Peak-to-peak | 59 | |||
| Clock Phase Delay, XI Input to MII TXC Output | 20 | 25 | ns | XI (25 MHz clock input) to MII TXC (25 MHz clock output) delay, referenced to rising edges of both clocks. Applies only to KSZ8091MNX in MII mode | 59 | ||
| Thermal Resistance (ΘJA) | ΘJA | 45.87 | °C/W | 57 | |||
| Thermal Resistance (ΘJC) | ΘJC | 15.85 | °C/W | 57 | |||
| Link Loss Reaction (Indication) Time | tllr | 4.4 | μs | Link loss detected at receive differential inputs to PHY signal indication time | 59 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | ppa | 1 = RXC clock is stoppable for 100BASE-TX | 52 |
CAD (KiCad official)
- Symbol:
KSZ8091MNXCA - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
ksz8091mnxca-etched.step/ksz8091mnxca-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz8091mnxca.step/ksz8091mnxca.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet, copy hosted by LCSC (80 pp, sha256
a7e3aab56aae2ff4, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).