main
History Download
Ray Publish 0.1.0 124a45f

KSZ8091MNXCA

Microchip Tech · Ethernet ICs · QFN-32-EP(5x5)

KSZ8091MNXCA from Microchip Tech, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground pin for the device.
2 VDD_1.2 power_out 1.2V core VDD supplied by the internal regulator; decouple with 2.2 μF and 0.1 μF capacitors to ground.
3 VDDA_3.3 power_in 3.3V analog VDD; connect to the board 3.3V supply through a ferrite bead and decouple with 22 μF and 0.1 μF capacitors to ground.
4 RXM bidirectional Physical receive or transmit signal, negative differential pair.
5 RXP bidirectional Physical receive or transmit signal, positive differential pair.
6 TXM bidirectional Physical transmit or receive signal, negative differential pair.
7 TXP bidirectional Physical transmit or receive signal, positive differential pair.
8 XO output Crystal feedback for the 25 MHz crystal; no connect if an oscillator or external clock source is used.
9 XI input Crystal, oscillator or external clock input at 25 MHz ±50 ppm.
10 REXT input Sets the PHY transmit output current; connect a 6.49 kΩ resistor to ground on this pin.
11 MDIO bidirectional MII management data I/O with a weak pull-up, open-drain output, and a required external 1.0 kΩ pull-up resistor.
12 MDC input MII management clock input, synchronous to the MDIO data pin.
13 RXD3/PHYAD0 bidirectional MII receive data output bit 3; in config mode the pull-up/pull-down is latched as PHYADDR[0] at reset de-assertion.
14 RXD2/PHYAD1 bidirectional MII receive data output bit 2; in config mode the pull-up/pull-down is latched as PHYADDR[1] at reset de-assertion.
15 RXD1/PHYAD2 bidirectional MII receive data output bit 1; in config mode the pull-up/pull-down is latched as PHYADDR[2] at reset de-assertion.
16 RXD0/DUPLEX bidirectional MII receive data output bit 0; in config mode the pull-up/pull-down is latched as DUPLEX at reset de-assertion.
17 VDDIO power_in 3.3V, 2.5V, or 1.8V digital VDD; decouple with 22 μF and 0.1 μF capacitors to ground.
18 RXDV/CONFIG2 bidirectional MII receive data valid output; in config mode it is latched as CONFIG2 at reset de-assertion.
19 RXC/B-CAST_OFF bidirectional MII receive clock output; in config mode it is latched as B-CAST_OFF at reset de-assertion.
20 RXER/ISO bidirectional MII receive error output; in config mode it is latched as ISOLATE at reset de-assertion.
21 INTRP/PME_N2/NAND_Tree# bidirectional Programmable interrupt output, active low by default, with a weak pull-up, open-drain output, and a required 1.0 kΩ pull-up to VDDIO for interrupt and PME functions.
22 TXC/PME_EN bidirectional MII transmit clock output; no connection in MII back-to-back mode, and latched as PME_EN in config mode.
23 TXEN input MII transmit enable input.
24 TXD0 input MII transmit data input bit 0, synchronous to TXC.
25 TXD1 input MII transmit data input bit 1, synchronous to TXC.
26 TXD2 input MII transmit data input bit 2, synchronous to TXC.
27 TXD3 input MII transmit data input bit 3, synchronous to TXC.
28 COL/CONFIG0 bidirectional MII collision detect output; in config mode it is latched as CONFIG0 at reset de-assertion.
29 CRS/CONFIG1 bidirectional MII carrier sense output; in config mode it is latched as CONFIG1 at reset de-assertion and serves as the NAND tree output.
30 LED0/PME_N1/NWAYEN bidirectional Programmable LED0 output; in config mode it is latched as auto-negotiation enable at reset de-assertion, and can serve as an open-drain PME_N output needing a 1.0 kΩ pull-up to VDDIO.
31 TXER input MII transmit error input; must be pulled high by a pull-up resistor for NAND tree testing.
32 RST# input Chip reset, active low, with an internal weak pull-up.
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-32-EP(5x5)
Category Communication Interface Chip/UART/485/232
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (VDD_1.2) VIN -0.5 1.8 V 57
Supply Voltage (VDDIO, VDDA_3.3) VIN -0.5 5 V 57
Input Voltage (all inputs) -0.5 5 V 57
Output Voltage (all outputs) -0.5 5 V 57
Lead Temperature 260 °C soldering, 10s 57
Storage Temperature TS -55 150 °C 57
Supply Voltage (VDDIO_3.3, VDDA_3.3) 3.135 3.465 V 57
Supply Voltage (VDDIO_2.5) 2.375 2.625 V 57
Supply Voltage (VDDIO_1.8) 1.71 1.89 V 57
Ambient Temperature (TA Commercial) TA 0 70 °C TA Commercial grade 57
Ambient Temperature (TA Industrial) TA -40 85 °C TA Industrial grade 57
Maximum Junction Temperature TJ 125 °C 57
Input High Voltage VIH 2 V VDDIO = 3.3V 58
Input High Voltage VIH 1.8 V VDDIO = 2.5V 58
Input High Voltage VIH 1.3 V VDDIO = 1.8V 58
Input Low Voltage VIL 0.8 V VDDIO = 3.3V 58
Input Low Voltage VIL 0.7 V VDDIO = 2.5V 58
Input Low Voltage VIL 0.5 V VDDIO = 1.8V 58
Input Current /IIN/ 10 μA VIN = GND ~ VDDIO 58
Output High Voltage VOH 2.4 V VDDIO = 3.3V 58
Output High Voltage VOH 2 V VDDIO = 2.5V 58
Output High Voltage VOH 1.5 V VDDIO = 1.8V 58
Output Low Voltage VOL 0.4 V VDDIO = 3.3V 58
Output Low Voltage VOL 0.3 V VDDIO = 1.8V 58
Output Tri-State Leakage /IOZ/ 10 μA 58
Internal Pull-Up Resistance pu 30 45 73 kΩ VDDIO = 3.3V 58
Internal Pull-Up Resistance pu 39 61 102 kΩ VDDIO = 2.5V 58
Internal Pull-Up Resistance pu 48 99 178 kΩ VDDIO = 1.8V 58
Internal Pull-Down Resistance pd 26 43 79 kΩ VDDIO = 3.3V 58
Internal Pull-Down Resistance pd 34 59 113 kΩ VDDIO = 2.5V 58
Internal Pull-Down Resistance pd 53 99 200 kΩ VDDIO = 1.8V 58
Peak Differential Output Voltage (100BASE-TX) VO 0.95 1.05 V 100Ω termination across differential output 58
Output Voltage Imbalance VIMB 2 % 100Ω termination across differential output 58
Rise/Fall Time (100BASE-TX) tr/tf 3 5 ns 58
Duty Cycle Distortion -0.25 0.25 ns 58
Overshoot 5 % 58
Peak Differential Output Voltage (10BASE-T) VP 2.2 2.8 V 100Ω termination across differential output 59
Jitter Added (10BASE-T) 3.5 ns Peak-to-peak 59
Clock Phase Delay, XI Input to MII TXC Output 20 25 ns XI (25 MHz clock input) to MII TXC (25 MHz clock output) delay, referenced to rising edges of both clocks. Applies only to KSZ8091MNX in MII mode 59
Thermal Resistance (ΘJA) ΘJA 45.87 °C/W 57
Thermal Resistance (ΘJC) ΘJC 15.85 °C/W 57
Link Loss Reaction (Indication) Time tllr 4.4 μs Link loss detected at receive differential inputs to PHY signal indication time 59

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing ppa 1 = RXC clock is stoppable for 100BASE-TX 52

CAD (KiCad official)

  • Symbol: KSZ8091MNXCA
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: ksz8091mnxca-etched.step / ksz8091mnxca-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ksz8091mnxca.step / ksz8091mnxca.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet, copy hosted by LCSC (80 pp, sha256 a7e3aab56aae2ff4, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF