Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

INA190A3IDDFR

Texas Instruments · Current Sense Amplifiers · TSOT-23-8

INA190A3IDDFR from Texas Instruments, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VS power_in Analog power supply, 1.7 V to 5.5 V.
2 ENABLE input Enable control pin; when driven to VS the device is enabled as a current sense amplifier, when driven to GND the device is disabled with reduced supply current and output placed in high-impedance state.
3 REF input Reference input enabling bidirectional current sensing with externally applied offset voltage.
4 GND power_in Analog ground.
5 OUT output Analog output providing the gained voltage difference from IN+ to IN- offset by the voltage applied to REF.
6 NC unconnected Not internally connected; either float or connect to any voltage between GND and VS.
7 IN+ input Current-sense amplifier positive input; connect to bus voltage side of sense resistor for high-side sensing or load side for low-side sensing.
8 IN- input Current-sense amplifier negative input; connect to load side of sense resistor for high-side sensing or ground side for low-side sensing.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSOT-23-8
Category Amplifiers/Comparators
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VS 6 V 4
Differential analog input voltage (VIN+) – (VIN–) -42 42 V 4
Analog input voltage with respect to GND VIN+, VIN– -0.3 42 V With respect to GND 4
ENABLE pin voltage VENABLE -0.3 6 V With respect to GND 4
REF, OUT pin voltage REF, OUT -0.3 0.3 V Max is (VS) + 0.3 V; min is GND – 0.3 V 4
Input current into any pin 5 mA 4
Operating temperature TA -55 150 °C 4
Junction temperature TJ 150 °C 4
Storage temperature Tstg -65 150 °C 4
Common-mode input range VCM -0.2 40 V Printed as GND – 0.2 to 40 V 4
Input pin voltage range VIN+, VIN– -0.2 40 V Printed as GND – 0.2 to 40 V 4
Operating supply voltage VS 1.7 5.5 V 4
Operating free-air temperature TA -40 125 °C 4
Common-mode rejection ratio CMRR 132 150 dB VSENSE = 0 mV, VIN+ = –0.1 V to 40 V, TA = –40°C to +125°C 5
Offset voltage, RTI VOS -15 -3 15 µV VS = 1.8 V, VSENSE = 0 mV 5
Offset drift, RTI dVOS/dT 10 80 nV/°C VSENSE = 0 mV, TA = –40°C to +125°C 5
Power-supply rejection ratio, RTI PSRR -5 -1 5 µV/V VSENSE = 0 mV, VS = 1.7 V to 5.5 V 5
Input bias current IIB 0.5 3 nA VSENSE = 0 mV 5
Input offset current IIO -0.07 0.07 nA VSENSE = 0 mV 5
Gain error (A2, A3, A4 devices) EG -0.3 -0.06 0.3 % VOUT = 0.1 V to VS – 0.1 V 5
Gain error drift 2 7 ppm/°C TA = –40°C to +125°C 5
Nonlinearity error -0.01 0.01 % VOUT = 0.1 V to VS – 0.1 V 5
Reference voltage rejection ratio (A3 devices) RVRR -4 0.5 4 µV/V VREF = 100 mV to VS – 100 mV, TA = –40°C to +125°C 5
Maximum capacitive load 1 nF No sustained oscillation 5
Swing to VS power-supply rail (offset from VS) VSP -20 -40 mV VS = 1.8 V, RL = 10 kΩ to GND, TA = –40°C to +125°C 5
Swing to GND (offset from GND) VSN 0.05 1 mV VS = 1.8 V, RL = 10 kΩ to GND, TA = –40°C to +125°C, VSENSE = –10 mV, VREF = 0 V 5
Zero current output voltage (A1, A2, A3 devices, offset from GND) VZL 1 3 mV VS = 1.8 V, RL = 10 kΩ to GND, TA = –40°C to +125°C, VSENSE = 0 mV, VREF = 0 V 5
Leakage input current (ENABLE) IEN 1 100 nA 0 V ≤ VENABLE ≤ VS 6
High-level input voltage (ENABLE) VIH 0.7 6 V Printed min as 0.7 × VS; max 6 V 6
Low-level input voltage (ENABLE) VIL 0 0.3 × VS Printed as 0 and 0.3 × VS 6
Output leakage, disabled IODIS 1 5 µA VS = 5.0 V, VOUT = 0 V to 5.0 V, VENABLE = 0 V 6
Quiescent current IQ 48 65 µA VS = 1.8 V, VSENSE = 0 mV 6
Quiescent current over temperature IQ 90 µA VS = 1.8 V, VSENSE = 0 mV, TA = –40°C to +125°C 6
Quiescent current, disabled IQDIS 10 100 nA VENABLE = 0 V, VSENSE = 0 mV 6
Junction-to-ambient thermal resistance (DDF, SOT-23) RθJA 170.7 °C/W 4
Junction-to-case (top) thermal resistance (DDF, SOT-23) RθJC(top) 132.7 °C/W 4
Junction-to-board thermal resistance (DDF, SOT-23) RθJB 65.3 °C/W 4
Junction-to-top characterization parameter (DDF, SOT-23) ΨJT 45.7 °C/W 4
Junction-to-board characterization parameter (DDF, SOT-23) ΨJB 65.2 °C/W 4

CAD (KiCad official)

  • Symbol: INA190A3IDDFR
  • Footprint: Package_TO_SOT_SMD:TSOT-23-8
  • 3D model: TSOT-23-8 (KiCad packages3D, STEP)
  • 3D model files: ina190a3iddfr-etched.step / ina190a3iddfr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina190a3iddfr.step / ina190a3iddfr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (47 pp, sha256 38a7102701707c17, retrieved 2026-09-26, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF