main
Ray
Publish 0.1.2
8df0d13
HV513WG-G
Microchip Tech · Registers · SOIC-24-300mil
HV513WG-G from Microchip Tech, in a SOIC-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connection. |
| 2 | VDD | power_in | Logic supply voltage, recommended operating range 4.5 V to 5.5 V (5 V typical). |
| 3 | DOUT | output | Data output buffer provided for cascading to the next HV513 DIN. |
| 4 | BL | input | Blanking input; a logic low sets all HVOUT outputs low, and the pin has an internal 20 kΩ pull-up resistor. |
| 5 | POL | input | Polarity bar input logic, with an internal 20 kΩ pull-up resistor. |
| 6 | CLK | input | Clock input; the shift register shifts data on the rising edge, with clock frequency 0 to 8 MHz. |
| 7 | LE | input | Latch enable bar input logic; data transfers from the shift register to the latch when LE is high and is stored when LE is low, with an internal 20 kΩ pull-up resistor. |
| 8 | SHORT | output | Short-circuit detect output; it goes low when an output does not reach its required state. |
| 9 | Hi-Z | input | High-impedance control; a logic low sets all outputs to a high-impedance state, with an internal 20 kΩ pull-up resistor. |
| 10 | DIN | input | Serial data input to the 8-bit shift register. |
| 11 | LGND | power_in | Low-voltage ground. |
| 12 | NC | unconnected | No connection. |
| 13 | HVGND | power_in | High-voltage ground; connection to all power and ground pads is required. |
| 14 | HVGND | power_in | High-voltage ground; connection to all power and ground pads is required. |
| 15 | HVOUT1 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 16 | HVOUT2 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 17 | HVOUT3 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 18 | HVOUT4 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 19 | HVOUT5 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 20 | HVOUT6 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 21 | HVOUT7 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 22 | HVOUT8 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 23 | VPP | power_in | High-voltage supply, recommended operating range 50 V to 250 V. |
| 24 | VPP | power_in | High-voltage supply, recommended operating range 50 V to 250 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-24-300mil |
| Category | Logic ICs |
| Pins | 24 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Logic Supply Voltage (absolute maximum) | VDD | -0.5 | 6 | V | 4 | ||
| Logic Input Levels (absolute maximum, lower limit) | -0.5 | V | 4 | ||||
| Ground Current | 0.3 | A | Note 1 | 4 | |||
| High-Voltage Supply Current | 0.25 | A | Note 1 | 4 | |||
| Maximum Junction Temperature | TJ(MAX) | 125 | °C | 4 | |||
| Storage Temperature | TS | -65 | 150 | °C | 4 | ||
| Continuous Total Power Dissipation, 24-lead SOW | 750 | mW | Note 2 | 4 | |||
| Logic Supply Voltage | VDD | 4.5 | 5 | 5.5 | V | 4 | |
| High-Voltage Supply Voltage | VPP | 50 | 250 | V | Note 1 | 4 | |
| Low-Level Input Voltage | VIL | 0 | 0.9 | V | 4 | ||
| Operating Junction Temperature | TJ | -40 | 85 | °C | 4 | ||
| VDD Supply Current | IDD | 4 | mA | fCLK = 8 MHz, LE = Low | 5 | ||
| Quiescent VDD Supply Current | IDDQ | 0.1 | mA | All VIN = VDD | 5 | ||
| Quiescent VDD Supply Current | IDDQ | 2 | mA | All VIN = 0V | 5 | ||
| High-Voltage Supply Current | IPP | 100 | µA | VPP = 250V, fOUT = 300 Hz, no load | 5 | ||
| Quiescent VPP Supply Voltage | IPPQ | 100 | µA | VPP = 240V, outputs are static | 5 | ||
| High-Level Logic Input Current | IIH | 10 | µA | VIH = VDD | 5 | ||
| Low-Level Logic Input Current | IIL | -10 | µA | VIL = 0V | 5 | ||
| Low-Level Logic Input Current (inputs with pull-up resistors) | IIL | -350 | µA | VIL = 0V, for inputs with pull-up resistors | 5 | ||
| High-Level Output HVOUT | VOH | 140 | V | VPP = 200V, IHVOUT = -20 mA | 5 | ||
| Low-Level Output HVOUT | VOL | 60 | V | VDD = 4.5V, IHVOUT = 20 mA | 5 | ||
| Low-Level Output Data Out | VOL | 1 | V | IDOUT = -0.1 mA | 5 | ||
| Clock Frequency | fCLK | 0 | 8 | MHz | 5 | ||
| Clock Width High and Low | tWL, tWH | 62 | ns | 5 | |||
| Data Set-Up Time before Clock Rises | tSU | 15 | ns | 5 | |||
| Data Hold Time after Clock Rises | tH | 30 | ns | 5 | |||
| Latch Enable Pulse Width | tWLE | 80 | ns | 5 | |||
| Latch Enable Delay Time after Rising Edge of Clock | tDLE | 35 | ns | 5 | |||
| Latch Enable Set-Up Time before Clock Rises | tSLE | 40 | ns | 5 | |||
| HVOUT Rise/Fall Time | tOR, tOF | 1000 | µs | CL = 100 nF, VPP = 200V | 5 | ||
| Delay Time for Output to Start Rise/Fall | tdON/OFF | 500 | ns | 5 | |||
| Delay Time Clock to Data Low to High | tDLH | 110 | ns | CL = 15 pF | 5 | ||
| Delay Time Clock to Data High to Low | tDHL | 110 | ns | CL = 15 pF | 5 | ||
| All Logic Inputs Rise/Fall Time | tr, tf | 5 | ns | 5 | |||
| Output Short-Circuit Detection | tSD | 500 | ns | CL = 15 pF, short to output fall of SHORT | 5 | ||
| Output Short-Circuit Clear | tSC | 3000 | ns | Short clear to output rise of SHORT | 5 | ||
| Output High-Z State | tHI-Z | 500 | ns | 5 | |||
| Operating Junction Temperature (temperature specifications) | TJ | -40 | 85 | °C | 6 | ||
| Maximum Junction Temperature (temperature specifications) | TJ(MAX) | 125 | °C | 6 | |||
| Storage Temperature (temperature specifications) | TS | -65 | 150 | °C | 6 | ||
| Thermal Resistance, Junction to Ambient, 24-lead SOW | JA | 44 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
HV513WG-G - Footprint:
Package_SO:SOIC-24W_7.5x15.4mm_P1.27mm - 3D model: SOIC-24-300mil (KiCad packages3D, STEP)
- 3D model files:
hv513wg-g-etched.step/hv513wg-g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hv513wg-g.step/hv513wg-g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (18 pp, sha256
5548f5efe1a70740, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# HV513WG-G
**Microchip Tech** · Registers · SOIC-24-300mil
HV513WG-G from Microchip Tech, in a SOIC-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connection. |
| 2 | VDD | power_in | Logic supply voltage, recommended operating range 4.5 V to 5.5 V (5 V typical). |
| 3 | DOUT | output | Data output buffer provided for cascading to the next HV513 DIN. |
| 4 | BL | input | Blanking input; a logic low sets all HVOUT outputs low, and the pin has an internal 20 kΩ pull-up resistor. |
| 5 | POL | input | Polarity bar input logic, with an internal 20 kΩ pull-up resistor. |
| 6 | CLK | input | Clock input; the shift register shifts data on the rising edge, with clock frequency 0 to 8 MHz. |
| 7 | LE | input | Latch enable bar input logic; data transfers from the shift register to the latch when LE is high and is stored when LE is low, with an internal 20 kΩ pull-up resistor. |
| 8 | SHORT | output | Short-circuit detect output; it goes low when an output does not reach its required state. |
| 9 | Hi-Z | input | High-impedance control; a logic low sets all outputs to a high-impedance state, with an internal 20 kΩ pull-up resistor. |
| 10 | DIN | input | Serial data input to the 8-bit shift register. |
| 11 | LGND | power_in | Low-voltage ground. |
| 12 | NC | unconnected | No connection. |
| 13 | HVGND | power_in | High-voltage ground; connection to all power and ground pads is required. |
| 14 | HVGND | power_in | High-voltage ground; connection to all power and ground pads is required. |
| 15 | HVOUT1 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 16 | HVOUT2 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 17 | HVOUT3 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 18 | HVOUT4 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 19 | HVOUT5 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 20 | HVOUT6 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 21 | HVOUT7 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 22 | HVOUT8 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |
| 23 | VPP | power_in | High-voltage supply, recommended operating range 50 V to 250 V. |
| 24 | VPP | power_in | High-voltage supply, recommended operating range 50 V to 250 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-24-300mil |
| Category | Logic ICs |
| Pins | 24 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Logic Supply Voltage (absolute maximum) | VDD | -0.5 | | 6 | V | | 4 |
| Logic Input Levels (absolute maximum, lower limit) | | -0.5 | | | V | | 4 |
| Ground Current | | | | 0.3 | A | Note 1 | 4 |
| High-Voltage Supply Current | | | | 0.25 | A | Note 1 | 4 |
| Maximum Junction Temperature | TJ(MAX) | | | 125 | °C | | 4 |
| Storage Temperature | TS | -65 | | 150 | °C | | 4 |
| Continuous Total Power Dissipation, 24-lead SOW | | | | 750 | mW | Note 2 | 4 |
| Logic Supply Voltage | VDD | 4.5 | 5 | 5.5 | V | | 4 |
| High-Voltage Supply Voltage | VPP | 50 | | 250 | V | Note 1 | 4 |
| Low-Level Input Voltage | VIL | 0 | | 0.9 | V | | 4 |
| Operating Junction Temperature | TJ | -40 | | 85 | °C | | 4 |
| VDD Supply Current | IDD | | | 4 | mA | fCLK = 8 MHz, LE = Low | 5 |
| Quiescent VDD Supply Current | IDDQ | | | 0.1 | mA | All VIN = VDD | 5 |
| Quiescent VDD Supply Current | IDDQ | | | 2 | mA | All VIN = 0V | 5 |
| High-Voltage Supply Current | IPP | | | 100 | µA | VPP = 250V, fOUT = 300 Hz, no load | 5 |
| Quiescent VPP Supply Voltage | IPPQ | | | 100 | µA | VPP = 240V, outputs are static | 5 |
| High-Level Logic Input Current | IIH | | | 10 | µA | VIH = VDD | 5 |
| Low-Level Logic Input Current | IIL | | | -10 | µA | VIL = 0V | 5 |
| Low-Level Logic Input Current (inputs with pull-up resistors) | IIL | | | -350 | µA | VIL = 0V, for inputs with pull-up resistors | 5 |
| High-Level Output HVOUT | VOH | 140 | | | V | VPP = 200V, IHVOUT = -20 mA | 5 |
| Low-Level Output HVOUT | VOL | | | 60 | V | VDD = 4.5V, IHVOUT = 20 mA | 5 |
| Low-Level Output Data Out | VOL | | | 1 | V | IDOUT = -0.1 mA | 5 |
| Clock Frequency | fCLK | 0 | | 8 | MHz | | 5 |
| Clock Width High and Low | tWL, tWH | 62 | | | ns | | 5 |
| Data Set-Up Time before Clock Rises | tSU | 15 | | | ns | | 5 |
| Data Hold Time after Clock Rises | tH | 30 | | | ns | | 5 |
| Latch Enable Pulse Width | tWLE | 80 | | | ns | | 5 |
| Latch Enable Delay Time after Rising Edge of Clock | tDLE | 35 | | | ns | | 5 |
| Latch Enable Set-Up Time before Clock Rises | tSLE | 40 | | | ns | | 5 |
| HVOUT Rise/Fall Time | tOR, tOF | | | 1000 | µs | CL = 100 nF, VPP = 200V | 5 |
| Delay Time for Output to Start Rise/Fall | tdON/OFF | | | 500 | ns | | 5 |
| Delay Time Clock to Data Low to High | tDLH | | | 110 | ns | CL = 15 pF | 5 |
| Delay Time Clock to Data High to Low | tDHL | | | 110 | ns | CL = 15 pF | 5 |
| All Logic Inputs Rise/Fall Time | tr, tf | | | 5 | ns | | 5 |
| Output Short-Circuit Detection | tSD | | | 500 | ns | CL = 15 pF, short to output fall of SHORT | 5 |
| Output Short-Circuit Clear | tSC | | | 3000 | ns | Short clear to output rise of SHORT | 5 |
| Output High-Z State | tHI-Z | | | 500 | ns | | 5 |
| Operating Junction Temperature (temperature specifications) | TJ | -40 | | 85 | °C | | 6 |
| Maximum Junction Temperature (temperature specifications) | TJ(MAX) | | | 125 | °C | | 6 |
| Storage Temperature (temperature specifications) | TS | -65 | | 150 | °C | | 6 |
| Thermal Resistance, Junction to Ambient, 24-lead SOW | JA | | 44 | | °C/W | | 6 |
## CAD (KiCad official)
- Symbol: `HV513WG-G`
- Footprint: `Package_SO:SOIC-24W_7.5x15.4mm_P1.27mm`
- 3D model: SOIC-24-300mil (KiCad packages3D, STEP)
- 3D model files: `hv513wg-g-etched.step` / `hv513wg-g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hv513wg-g.step` / `hv513wg-g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/HV513-8-Channel-Serial-to-Parallel-Converter-with-High-Voltage-Push-Pull-Outputs-Polarity-Hi-Z-and-Short-Circuit-Detect-Data-Sheet.pdf) (18 pp, sha256 `5548f5efe1a70740`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/hv513wg-g-datasheet.pdf)