main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers hv513wg-g: viewers rendered from the public page · Ray
hv513wg-g-etched.glb Publish 0.1.0 · Ray
hv513wg-g-etched.step hv513wg-g: factory component page (tier=mfr) · Ray
hv513wg-g-hero.glb hv513wg-g: hero GLB from the etched model (keeps the MPN mark) · Ray
hv513wg-g-hero.overlay.json Publish 0.1.1 · Ray
hv513wg-g.glb Publish 0.1.0 · Ray
hv513wg-g.kicad_mod Publish 0.1.0 · Ray
hv513wg-g.kicad_sym Publish 0.1.0 · Ray
hv513wg-g.lbr Publish 0.1.0 · Ray
hv513wg-g.step Publish 0.1.0 · Ray
package.json Publish 0.1.2 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.2 · Ray
verification.json Verified: Rebuilt by the parts factory: tier mfr, 24 pins · Ray

HV513WG-G

Microchip Tech · Registers · SOIC-24-300mil

HV513WG-G from Microchip Tech, in a SOIC-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connection.
2 VDD power_in Logic supply voltage, recommended operating range 4.5 V to 5.5 V (5 V typical).
3 DOUT output Data output buffer provided for cascading to the next HV513 DIN.
4 BL input Blanking input; a logic low sets all HVOUT outputs low, and the pin has an internal 20 kΩ pull-up resistor.
5 POL input Polarity bar input logic, with an internal 20 kΩ pull-up resistor.
6 CLK input Clock input; the shift register shifts data on the rising edge, with clock frequency 0 to 8 MHz.
7 LE input Latch enable bar input logic; data transfers from the shift register to the latch when LE is high and is stored when LE is low, with an internal 20 kΩ pull-up resistor.
8 SHORT output Short-circuit detect output; it goes low when an output does not reach its required state.
9 Hi-Z input High-impedance control; a logic low sets all outputs to a high-impedance state, with an internal 20 kΩ pull-up resistor.
10 DIN input Serial data input to the 8-bit shift register.
11 LGND power_in Low-voltage ground.
12 NC unconnected No connection.
13 HVGND power_in High-voltage ground; connection to all power and ground pads is required.
14 HVGND power_in High-voltage ground; connection to all power and ground pads is required.
15 HVOUT1 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
16 HVOUT2 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
17 HVOUT3 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
18 HVOUT4 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
19 HVOUT5 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
20 HVOUT6 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
21 HVOUT7 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
22 HVOUT8 output High-voltage push-pull output; it may not switch below the minimum VPP of 50 V.
23 VPP power_in High-voltage supply, recommended operating range 50 V to 250 V.
24 VPP power_in High-voltage supply, recommended operating range 50 V to 250 V.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-24-300mil
Category Logic ICs
Pins 24

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Logic Supply Voltage (absolute maximum) VDD -0.5 6 V 4
Logic Input Levels (absolute maximum, lower limit) -0.5 V 4
Ground Current 0.3 A Note 1 4
High-Voltage Supply Current 0.25 A Note 1 4
Maximum Junction Temperature TJ(MAX) 125 °C 4
Storage Temperature TS -65 150 °C 4
Continuous Total Power Dissipation, 24-lead SOW 750 mW Note 2 4
Logic Supply Voltage VDD 4.5 5 5.5 V 4
High-Voltage Supply Voltage VPP 50 250 V Note 1 4
Low-Level Input Voltage VIL 0 0.9 V 4
Operating Junction Temperature TJ -40 85 °C 4
VDD Supply Current IDD 4 mA fCLK = 8 MHz, LE = Low 5
Quiescent VDD Supply Current IDDQ 0.1 mA All VIN = VDD 5
Quiescent VDD Supply Current IDDQ 2 mA All VIN = 0V 5
High-Voltage Supply Current IPP 100 µA VPP = 250V, fOUT = 300 Hz, no load 5
Quiescent VPP Supply Voltage IPPQ 100 µA VPP = 240V, outputs are static 5
High-Level Logic Input Current IIH 10 µA VIH = VDD 5
Low-Level Logic Input Current IIL -10 µA VIL = 0V 5
Low-Level Logic Input Current (inputs with pull-up resistors) IIL -350 µA VIL = 0V, for inputs with pull-up resistors 5
High-Level Output HVOUT VOH 140 V VPP = 200V, IHVOUT = -20 mA 5
Low-Level Output HVOUT VOL 60 V VDD = 4.5V, IHVOUT = 20 mA 5
Low-Level Output Data Out VOL 1 V IDOUT = -0.1 mA 5
Clock Frequency fCLK 0 8 MHz 5
Clock Width High and Low tWL, tWH 62 ns 5
Data Set-Up Time before Clock Rises tSU 15 ns 5
Data Hold Time after Clock Rises tH 30 ns 5
Latch Enable Pulse Width tWLE 80 ns 5
Latch Enable Delay Time after Rising Edge of Clock tDLE 35 ns 5
Latch Enable Set-Up Time before Clock Rises tSLE 40 ns 5
HVOUT Rise/Fall Time tOR, tOF 1000 µs CL = 100 nF, VPP = 200V 5
Delay Time for Output to Start Rise/Fall tdON/OFF 500 ns 5
Delay Time Clock to Data Low to High tDLH 110 ns CL = 15 pF 5
Delay Time Clock to Data High to Low tDHL 110 ns CL = 15 pF 5
All Logic Inputs Rise/Fall Time tr, tf 5 ns 5
Output Short-Circuit Detection tSD 500 ns CL = 15 pF, short to output fall of SHORT 5
Output Short-Circuit Clear tSC 3000 ns Short clear to output rise of SHORT 5
Output High-Z State tHI-Z 500 ns 5
Operating Junction Temperature (temperature specifications) TJ -40 85 °C 6
Maximum Junction Temperature (temperature specifications) TJ(MAX) 125 °C 6
Storage Temperature (temperature specifications) TS -65 150 °C 6
Thermal Resistance, Junction to Ambient, 24-lead SOW JA 44 °C/W 6

CAD (KiCad official)

  • Symbol: HV513WG-G
  • Footprint: Package_SO:SOIC-24W_7.5x15.4mm_P1.27mm
  • 3D model: SOIC-24-300mil (KiCad packages3D, STEP)
  • 3D model files: hv513wg-g-etched.step / hv513wg-g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); hv513wg-g.step / hv513wg-g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (18 pp, sha256 5548f5efe1a70740, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF