← Commit history

Publish 0.1.2

Ray ·8df0d13cea · ·parent 556baed
3 files changed +95−93
README.md+32−30
@@ -2,36 +2,36 @@  **Microchip Tech** · Registers · SOIC-24-300mil -HV513WG-G from Microchip Tech, in a SOIC-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.+HV513WG-G from Microchip Tech, in a SOIC-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.  ## Pinout  | Pin | Name | Type | Function | |---|---|---|---| | 1 | NC | unconnected | No connection. |-| 2 | VDD | power_in | Logic supply voltage, recommended 4.5V to 5.5V (typ. 5V). |-| 3 | DOUT | output | Data output buffer for cascading to the next HV513; VOH is VDD-1V minimum at 0.1 mA and VOL is 1V maximum at 0.1 mA. |-| 4 | BL | input | Blanking input with internal 20 kΩ pull-up; a logic low sets all HVOUTs low. |-| 5 | POL | input | Active-low polarity input logic with internal 20 kΩ pull-up resistor. |-| 6 | CLK | input | Clock input; shift register shifts data on the low-to-high transition, up to 8 MHz at VDD = 5V. |-| 7 | LE | input | Active-low latch enable input with internal 20 kΩ pull-up; the latch stores data when LE is low and transfers the shift register to the latch when high. |-| 8 | SHORT | output | Short-circuit detect output that goes to logic 0 if an output does not reach its required state; it pulses low during normal output transitions. |-| 9 | Hi-Z | input | High-impedance control input with internal 20 kΩ pull-up; a logic low sets all outputs to a high-impedance state. |+| 2 | VDD | power_in | Logic supply voltage, recommended operating range 4.5 V to 5.5 V (5 V typical). |+| 3 | DOUT | output | Data output buffer provided for cascading to the next HV513 DIN. |+| 4 | BL | input | Blanking input; a logic low sets all HVOUT outputs low, and the pin has an internal 20 kΩ pull-up resistor. |+| 5 | POL | input | Polarity bar input logic, with an internal 20 kΩ pull-up resistor. |+| 6 | CLK | input | Clock input; the shift register shifts data on the rising edge, with clock frequency 0 to 8 MHz. |+| 7 | LE | input | Latch enable bar input logic; data transfers from the shift register to the latch when LE is high and is stored when LE is low, with an internal 20 kΩ pull-up resistor. |+| 8 | SHORT | output | Short-circuit detect output; it goes low when an output does not reach its required state. |+| 9 | Hi-Z | input | High-impedance control; a logic low sets all outputs to a high-impedance state, with an internal 20 kΩ pull-up resistor. | | 10 | DIN | input | Serial data input to the 8-bit shift register. | | 11 | LGND | power_in | Low-voltage ground. | | 12 | NC | unconnected | No connection. | | 13 | HVGND | power_in | High-voltage ground; connection to all power and ground pads is required. | | 14 | HVGND | power_in | High-voltage ground; connection to all power and ground pads is required. |-| 15 | HVOUT1 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 16 | HVOUT2 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 17 | HVOUT3 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 18 | HVOUT4 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 19 | HVOUT5 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 20 | HVOUT6 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 21 | HVOUT7 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 22 | HVOUT8 | output | High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low. |-| 23 | VPP | power_in | High-voltage supply, recommended 50V to 250V; the output may not switch below the minimum VPP. |-| 24 | VPP | power_in | High-voltage supply, recommended 50V to 250V; the output may not switch below the minimum VPP. |+| 15 | HVOUT1 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 16 | HVOUT2 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 17 | HVOUT3 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 18 | HVOUT4 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 19 | HVOUT5 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 20 | HVOUT6 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 21 | HVOUT7 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 22 | HVOUT8 | output | High-voltage push-pull output; it may not switch below the minimum VPP of 50 V. |+| 23 | VPP | power_in | High-voltage supply, recommended operating range 50 V to 250 V. |+| 24 | VPP | power_in | High-voltage supply, recommended operating range 50 V to 250 V. |  ## Key specifications @@ -48,18 +48,17 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| Logic Supply Voltage | VDD | 4.5 | 5 | 5.5 | V |  | 4 |-| High-Voltage Supply Voltage | VPP | 50 |  | 250 | V | Note 1 | 4 |-| Low-Level Input Voltage | VIL | 0 |  | 0.9 | V |  | 4 |-| Operating Junction Temperature | TJ | -40 |  | 85 | °C |  | 4 |-| Logic Supply Voltage | VDD | -0.5 |  | 6 | V |  | 4 |-| High-Voltage Supply | VPP |  |  | 275 | V |  | 4 |-| Logic Input Levels |  | -0.5 |  |  | V |  | 4 |+| Logic Supply Voltage (absolute maximum) | VDD | -0.5 |  | 6 | V |  | 4 |+| Logic Input Levels (absolute maximum, lower limit) |  | -0.5 |  |  | V |  | 4 | | Ground Current |  |  |  | 0.3 | A | Note 1 | 4 | | High-Voltage Supply Current |  |  |  | 0.25 | A | Note 1 | 4 | | Maximum Junction Temperature | TJ(MAX) |  |  | 125 | °C |  | 4 | | Storage Temperature | TS | -65 |  | 150 | °C |  | 4 | | Continuous Total Power Dissipation, 24-lead SOW |  |  |  | 750 | mW | Note 2 | 4 |+| Logic Supply Voltage | VDD | 4.5 | 5 | 5.5 | V |  | 4 |+| High-Voltage Supply Voltage | VPP | 50 |  | 250 | V | Note 1 | 4 |+| Low-Level Input Voltage | VIL | 0 |  | 0.9 | V |  | 4 |+| Operating Junction Temperature | TJ | -40 |  | 85 | °C |  | 4 | | VDD Supply Current | IDD |  |  | 4 | mA | fCLK = 8 MHz, LE = Low | 5 | | Quiescent VDD Supply Current | IDDQ |  |  | 0.1 | mA | All VIN = VDD | 5 | | Quiescent VDD Supply Current | IDDQ |  |  | 2 | mA | All VIN = 0V | 5 |@@ -67,10 +66,10 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries | Quiescent VPP Supply Voltage | IPPQ |  |  | 100 | µA | VPP = 240V, outputs are static | 5 | | High-Level Logic Input Current | IIH |  |  | 10 | µA | VIH = VDD | 5 | | Low-Level Logic Input Current | IIL |  |  | -10 | µA | VIL = 0V | 5 |-| Low-Level Logic Input Current, inputs with pull-up resistors | IIL |  |  | -350 | µA | VIL = 0V, for inputs with pull-up resistors | 5 |+| Low-Level Logic Input Current (inputs with pull-up resistors) | IIL |  |  | -350 | µA | VIL = 0V, for inputs with pull-up resistors | 5 | | High-Level Output HVOUT | VOH | 140 |  |  | V | VPP = 200V, IHVOUT = -20 mA | 5 |-| Data Out (Low-Level Output) | VOL |  |  | 1 | V | IDOUT = -0.1 mA | 5 | | Low-Level Output HVOUT | VOL |  |  | 60 | V | VDD = 4.5V, IHVOUT = 20 mA | 5 |+| Low-Level Output Data Out | VOL |  |  | 1 | V | IDOUT = -0.1 mA | 5 | | Clock Frequency | fCLK | 0 |  | 8 | MHz |  | 5 | | Clock Width High and Low | tWL, tWH | 62 |  |  | ns |  | 5 | | Data Set-Up Time before Clock Rises | tSU | 15 |  |  | ns |  | 5 |@@ -86,7 +85,10 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries | Output Short-Circuit Detection | tSD |  |  | 500 | ns | CL = 15 pF, short to output fall of SHORT | 5 | | Output Short-Circuit Clear | tSC |  |  | 3000 | ns | Short clear to output rise of SHORT | 5 | | Output High-Z State | tHI-Z |  |  | 500 | ns |  | 5 |-| Thermal resistance, junction to ambient, 24-lead SOW | θJA |  | 44 |  | °C/W |  | 6 |+| Operating Junction Temperature (temperature specifications) | TJ | -40 |  | 85 | °C |  | 6 |+| Maximum Junction Temperature (temperature specifications) | TJ(MAX) |  |  | 125 | °C |  | 6 |+| Storage Temperature (temperature specifications) | TS | -65 |  | 150 | °C |  | 6 |+| Thermal Resistance, Junction to Ambient, 24-lead SOW | JA |  | 44 |  | °C/W |  | 6 |  ## CAD (KiCad official) @@ -99,7 +101,7 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Microchip Tech datasheet](docs/hv513wg-g-datasheet.pdf) (18 pp, sha256 `5548f5efe1a70740`, retrieved 2026-11-12, tier: manufacturer)+- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/HV513-8-Channel-Serial-to-Parallel-Converter-with-High-Voltage-Push-Pull-Outputs-Polarity-Hi-Z-and-Short-Circuit-Detect-Data-Sheet.pdf) (18 pp, sha256 `5548f5efe1a70740`, retrieved 2026-11-13, tier: manufacturer) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0). 
package.json+30−31
@@ -1,6 +1,6 @@ {   "slug": "hv513wg-g",-  "version": "0.1.1",+  "version": "0.1.2",   "type": "component",   "description": "Microchip Tech Registers, SOIC-24-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -28,8 +28,7 @@     "viewers/symbol.html",     "viewers/footprint.html",     "hv513wg-g-hero.glb",-    "hv513wg-g-hero.overlay.json",-    "hv513wg-g-etched.glb"+    "hv513wg-g-hero.overlay.json"   ],   "component": {     "mpn": "HV513WG-G",@@ -38,12 +37,12 @@     "pin_count": 24,     "category": "Logic ICs",     "subcategory": "Registers",-    "datasheet": "https://datasheet.lcsc.com/datasheet/pdf/883e10431043329bbc4eb9583f5220fa.pdf",+    "datasheet": "https://ww1.microchip.com/downloads/en/DeviceDoc/HV513-8-Channel-Serial-to-Parallel-Converter-with-High-Voltage-Push-Pull-Outputs-Polarity-Hi-Z-and-Short-Circuit-Detect-Data-Sheet.pdf",     "parts": {       "symbol": "hv513wg-g.kicad_sym",       "footprint": "hv513wg-g.kicad_mod",       "model_3d": "hv513wg-g-hero.glb",-      "model_3d_plain": "hv513wg-g-etched.glb",+      "model_3d_plain": "hv513wg-g.glb",       "model_3d_step": "hv513wg-g-etched.step",       "model_3d_step_plain": "hv513wg-g.step",       "lbr": "hv513wg-g.lbr"@@ -54,7 +53,7 @@       "mouser": "689-HV513WG-G"     },     "distributor_check": {-      "checked_at": "2026-11-12T07:58:33Z",+      "checked_at": "2026-11-13T00:38:17Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "HV513WG-GTR-ND",@@ -76,49 +75,49 @@         "number": "2",         "name": "VDD",         "type": "power_in",-        "description": "Logic supply voltage, recommended 4.5V to 5.5V (typ. 5V)."+        "description": "Logic supply voltage, recommended operating range 4.5 V to 5.5 V (5 V typical)."       },       {         "number": "3",         "name": "DOUT",         "type": "output",-        "description": "Data output buffer for cascading to the next HV513; VOH is VDD-1V minimum at 0.1 mA and VOL is 1V maximum at 0.1 mA."+        "description": "Data output buffer provided for cascading to the next HV513 DIN."       },       {         "number": "4",         "name": "BL",         "type": "input",-        "description": "Blanking input with internal 20 kΩ pull-up; a logic low sets all HVOUTs low."+        "description": "Blanking input; a logic low sets all HVOUT outputs low, and the pin has an internal 20 kΩ pull-up resistor."       },       {         "number": "5",         "name": "POL",         "type": "input",-        "description": "Active-low polarity input logic with internal 20 kΩ pull-up resistor."+        "description": "Polarity bar input logic, with an internal 20 kΩ pull-up resistor."       },       {         "number": "6",         "name": "CLK",         "type": "input",-        "description": "Clock input; shift register shifts data on the low-to-high transition, up to 8 MHz at VDD = 5V."+        "description": "Clock input; the shift register shifts data on the rising edge, with clock frequency 0 to 8 MHz."       },       {         "number": "7",         "name": "LE",         "type": "input",-        "description": "Active-low latch enable input with internal 20 kΩ pull-up; the latch stores data when LE is low and transfers the shift register to the latch when high."+        "description": "Latch enable bar input logic; data transfers from the shift register to the latch when LE is high and is stored when LE is low, with an internal 20 kΩ pull-up resistor."       },       {         "number": "8",         "name": "SHORT",         "type": "output",-        "description": "Short-circuit detect output that goes to logic 0 if an output does not reach its required state; it pulses low during normal output transitions."+        "description": "Short-circuit detect output; it goes low when an output does not reach its required state."       },       {         "number": "9",         "name": "Hi-Z",         "type": "input",-        "description": "High-impedance control input with internal 20 kΩ pull-up; a logic low sets all outputs to a high-impedance state."+        "description": "High-impedance control; a logic low sets all outputs to a high-impedance state, with an internal 20 kΩ pull-up resistor."       },       {         "number": "10",@@ -154,61 +153,61 @@         "number": "15",         "name": "HVOUT1",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "16",         "name": "HVOUT2",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "17",         "name": "HVOUT3",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "18",         "name": "HVOUT4",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "19",         "name": "HVOUT5",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "20",         "name": "HVOUT6",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "21",         "name": "HVOUT7",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "22",         "name": "HVOUT8",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "23",         "name": "VPP",         "type": "power_in",-        "description": "High-voltage supply, recommended 50V to 250V; the output may not switch below the minimum VPP."+        "description": "High-voltage supply, recommended operating range 50 V to 250 V."       },       {         "number": "24",         "name": "VPP",         "type": "power_in",-        "description": "High-voltage supply, recommended 50V to 250V; the output may not switch below the minimum VPP."+        "description": "High-voltage supply, recommended operating range 50 V to 250 V."       }     ],     "provenance": {@@ -222,14 +221,14 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: Datasheet lists these pins as no connection (NC) in the 24-lead SOW table; typed as unconnected.; Datasheet does not state whether SHORT is push-pull or open-drain; typed as output based on its logi; DOUT limits are given only as VOH/VOL at ±0.1 mA; VDD–1V and 1V values are quoted from the DC table."+          "extractor flagged: The datasheet calls this package 24-lead SOW (Wide Body, WG), not SOIC-24-300mil. It cites JEDEC MS-; Pin 1, pin 12 are marked NC (no connection) in Table 2-2; they are reported as unconnected and shoul; Table 2-2 gives the pin list only; the datasheet does not state a per-pin electrical limit for DOUT,"         ],         "pages_sent": 18,-        "cost_usd": 0.0738,-        "at": "2026-11-12T07:58:04"+        "cost_usd": 0.0759,+        "at": "2026-11-13T00:38:02"       },       "datasheet": {-        "url": "https://datasheet.lcsc.com/datasheet/pdf/883e10431043329bbc4eb9583f5220fa.pdf",+        "url": "https://ww1.microchip.com/downloads/en/DeviceDoc/HV513-8-Channel-Serial-to-Parallel-Converter-with-High-Voltage-Push-Pull-Outputs-Polarity-Hi-Z-and-Short-Circuit-Detect-Data-Sheet.pdf",         "pages": 18,         "sha256": "5548f5efe1a70740",         "source_tier": "mfr"@@ -263,7 +262,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "4b0d20f82f5b0124fecfe11c941274a3c865a30f7baee8b8fadd7df55972d4cd",-        "checked": "2026-11-12",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -281,8 +280,8 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "b89cc7034c99e176a1cfb3b8000ff2e63268dabaa384b8ab578b30cc87f1b8f2",-        "checked": "2026-11-12",+        "sha256": "e37d09f10437dde98c49c9c3cd7191114a22d07aa6fe8e0478464a6b21e70059",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],
page.json+33−32
@@ -4,7 +4,7 @@   "slug": "hv513wg-g",   "title": "HV513WG-G",   "brief": "Microchip Tech Registers, SOIC-24-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.1",+  "version": "0.1.2",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -20,12 +20,12 @@     "pin_count": 24,     "category": "Logic ICs",     "subcategory": "Registers",-    "datasheet": "https://datasheet.lcsc.com/datasheet/pdf/883e10431043329bbc4eb9583f5220fa.pdf",+    "datasheet": "https://ww1.microchip.com/downloads/en/DeviceDoc/HV513-8-Channel-Serial-to-Parallel-Converter-with-High-Voltage-Push-Pull-Outputs-Polarity-Hi-Z-and-Short-Circuit-Detect-Data-Sheet.pdf",     "parts": {       "symbol": "hv513wg-g.kicad_sym",       "footprint": "hv513wg-g.kicad_mod",       "model_3d": "hv513wg-g-hero.glb",-      "model_3d_plain": "hv513wg-g-etched.glb",+      "model_3d_plain": "hv513wg-g.glb",       "model_3d_step": "hv513wg-g-etched.step",       "model_3d_step_plain": "hv513wg-g.step",       "lbr": "hv513wg-g.lbr"@@ -36,7 +36,7 @@       "mouser": "689-HV513WG-G"     },     "distributor_check": {-      "checked_at": "2026-11-12T07:58:33Z",+      "checked_at": "2026-11-13T00:38:17Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "HV513WG-GTR-ND",@@ -58,49 +58,49 @@         "number": "2",         "name": "VDD",         "type": "power_in",-        "description": "Logic supply voltage, recommended 4.5V to 5.5V (typ. 5V)."+        "description": "Logic supply voltage, recommended operating range 4.5 V to 5.5 V (5 V typical)."       },       {         "number": "3",         "name": "DOUT",         "type": "output",-        "description": "Data output buffer for cascading to the next HV513; VOH is VDD-1V minimum at 0.1 mA and VOL is 1V maximum at 0.1 mA."+        "description": "Data output buffer provided for cascading to the next HV513 DIN."       },       {         "number": "4",         "name": "BL",         "type": "input",-        "description": "Blanking input with internal 20 kΩ pull-up; a logic low sets all HVOUTs low."+        "description": "Blanking input; a logic low sets all HVOUT outputs low, and the pin has an internal 20 kΩ pull-up resistor."       },       {         "number": "5",         "name": "POL",         "type": "input",-        "description": "Active-low polarity input logic with internal 20 kΩ pull-up resistor."+        "description": "Polarity bar input logic, with an internal 20 kΩ pull-up resistor."       },       {         "number": "6",         "name": "CLK",         "type": "input",-        "description": "Clock input; shift register shifts data on the low-to-high transition, up to 8 MHz at VDD = 5V."+        "description": "Clock input; the shift register shifts data on the rising edge, with clock frequency 0 to 8 MHz."       },       {         "number": "7",         "name": "LE",         "type": "input",-        "description": "Active-low latch enable input with internal 20 kΩ pull-up; the latch stores data when LE is low and transfers the shift register to the latch when high."+        "description": "Latch enable bar input logic; data transfers from the shift register to the latch when LE is high and is stored when LE is low, with an internal 20 kΩ pull-up resistor."       },       {         "number": "8",         "name": "SHORT",         "type": "output",-        "description": "Short-circuit detect output that goes to logic 0 if an output does not reach its required state; it pulses low during normal output transitions."+        "description": "Short-circuit detect output; it goes low when an output does not reach its required state."       },       {         "number": "9",         "name": "Hi-Z",         "type": "input",-        "description": "High-impedance control input with internal 20 kΩ pull-up; a logic low sets all outputs to a high-impedance state."+        "description": "High-impedance control; a logic low sets all outputs to a high-impedance state, with an internal 20 kΩ pull-up resistor."       },       {         "number": "10",@@ -136,61 +136,61 @@         "number": "15",         "name": "HVOUT1",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "16",         "name": "HVOUT2",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "17",         "name": "HVOUT3",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "18",         "name": "HVOUT4",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "19",         "name": "HVOUT5",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "20",         "name": "HVOUT6",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "21",         "name": "HVOUT7",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "22",         "name": "HVOUT8",         "type": "output",-        "description": "High-voltage push-pull output; with VPP = 200V and 20 mA source it sits at 140V minimum high, and with VDD = 4.5V and 20 mA sink it is 60V maximum low."+        "description": "High-voltage push-pull output; it may not switch below the minimum VPP of 50 V."       },       {         "number": "23",         "name": "VPP",         "type": "power_in",-        "description": "High-voltage supply, recommended 50V to 250V; the output may not switch below the minimum VPP."+        "description": "High-voltage supply, recommended operating range 50 V to 250 V."       },       {         "number": "24",         "name": "VPP",         "type": "power_in",-        "description": "High-voltage supply, recommended 50V to 250V; the output may not switch below the minimum VPP."+        "description": "High-voltage supply, recommended operating range 50 V to 250 V."       }     ],     "provenance": {@@ -204,14 +204,14 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: Datasheet lists these pins as no connection (NC) in the 24-lead SOW table; typed as unconnected.; Datasheet does not state whether SHORT is push-pull or open-drain; typed as output based on its logi; DOUT limits are given only as VOH/VOL at ±0.1 mA; VDD–1V and 1V values are quoted from the DC table."+          "extractor flagged: The datasheet calls this package 24-lead SOW (Wide Body, WG), not SOIC-24-300mil. It cites JEDEC MS-; Pin 1, pin 12 are marked NC (no connection) in Table 2-2; they are reported as unconnected and shoul; Table 2-2 gives the pin list only; the datasheet does not state a per-pin electrical limit for DOUT,"         ],         "pages_sent": 18,-        "cost_usd": 0.0738,-        "at": "2026-11-12T07:58:04"+        "cost_usd": 0.0759,+        "at": "2026-11-13T00:38:02"       },       "datasheet": {-        "url": "https://datasheet.lcsc.com/datasheet/pdf/883e10431043329bbc4eb9583f5220fa.pdf",+        "url": "https://ww1.microchip.com/downloads/en/DeviceDoc/HV513-8-Channel-Serial-to-Parallel-Converter-with-High-Voltage-Push-Pull-Outputs-Polarity-Hi-Z-and-Short-Circuit-Detect-Data-Sheet.pdf",         "pages": 18,         "sha256": "5548f5efe1a70740",         "source_tier": "mfr"@@ -245,7 +245,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "4b0d20f82f5b0124fecfe11c941274a3c865a30f7baee8b8fadd7df55972d4cd",-        "checked": "2026-11-12",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -263,8 +263,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "b89cc7034c99e176a1cfb3b8000ff2e63268dabaa384b8ab578b30cc87f1b8f2",-        "checked": "2026-11-12",+        "sha256": "e37d09f10437dde98c49c9c3cd7191114a22d07aa6fe8e0478464a6b21e70059",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],@@ -834,10 +834,11 @@     "viewers/symbol.html",     "viewers/footprint.html",     "hv513wg-g-hero.glb",-    "hv513wg-g-hero.overlay.json",-    "hv513wg-g-etched.glb"+    "hv513wg-g-hero.overlay.json"   ],   "visibility": {     "public": true-  }+  },+  "description": "Microchip Tech Registers, SOIC-24-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file