component
FT245RL-REEL
Public Made by Adomby adom
FTDI USB Converters, SSOP-28-208mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
FT245RL-REEL
FTDI · USB Converters · SSOP-28-208mil
FT245RL-REEL from FTDI, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D0 | bidirectional | FIFO data bus bit 0 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 2 | D4 | bidirectional | FIFO data bus bit 4 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 3 | D2 | bidirectional | FIFO data bus bit 2 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 4 | VCCIO | power_in | +1.8V to +5.25V supply to the FIFO interface group pins; connect to 3V3OUT for 3.3V output levels or to VCC for 5V CMOS output levels, or supply an external +1.8V to +2.8V source from the same source as VCC. |
| 5 | D1 | bidirectional | FIFO data bus bit 1 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 6 | D7 | bidirectional | FIFO data bus bit 7 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 7 | GND | power_in | Device ground supply pin. |
| 8 | NC | unconnected | No internal connection. |
| 9 | D5 | bidirectional | FIFO data bus bit 5 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 10 | D6 | bidirectional | FIFO data bus bit 6 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 11 | D3 | bidirectional | FIFO data bus bit 3 of the 8-bit D0...D7 parallel FIFO interface, powered from the VCCIO domain (+1.8V to +5.25V). |
| 12 | PWREN# | output | Goes low after USB configuration and high during USB suspend, intended to drive a P-channel logic-level MOSFET power switch for external logic, with a 10kΩ pull-up to VCCIO recommended. |
| 13 | RD# | input | Enables the current FIFO data byte on D0...D7 when low, and fetches the next receive FIFO byte on a high-to-low transition. |
| 14 | WR | input | Writes the data byte on D0...D7 into the transmit FIFO buffer on a high-to-low transition. |
| 15 | USBDP | bidirectional | USB data signal plus with internal series resistor and 1.5kΩ pull-up to 3.3V. |
| 16 | USBDM | bidirectional | USB data signal minus with internal series resistor. |
| 17 | 3V3OUT | power_out | +3.3V output from the integrated LDO regulator, to be decoupled with 100nF to ground, which can supply up to 50mA to external logic and can be used to supply VCCIO. |
| 18 | GND | power_in | Device ground supply pin. |
| 19 | RESET# | input | Active-low reset input that may be driven by an external device, and may be left unconnected or pulled up to VCC if not used. |
| 20 | VCC | power_in | +3.3V to +5.25V supply to the device core; a minimum of +4.0V is required when using the internal clock generator. |
| 21 | GND | power_in | Device ground supply pin. |
| 22 | TXE# | output | When high, data must not be written to the FIFO; when low, data can be written by strobing WR high then low, and the pin is tri-state during reset. |
| 23 | RXF# | output | When high, no data may be read from the FIFO; when low, data is available to read by strobing RD# low then high, and the pin is tri-state during reset. |
| 24 | NC | unconnected | No internal connection. |
| 25 | AGND | power_in | Device analogue ground supply for the internal clock multiplier. |
| 26 | TEST | input | Puts the device into IC test mode; must be tied to GND for normal operation, otherwise the device will appear to fail. |
| 27 | OSCI | input | Input to the 12MHz oscillator cell, optional and may be left unconnected for normal operation. |
| 28 | OSCO | output | Output from the 12MHz oscillator cell, optional and may be left unconnected for normal operation when the internal oscillator is used. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FTDI |
| Package | SSOP-28-208mil |
| Category | Interface |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -65 | 150 | °C | 17 | |||
| Ambient Temperature (Power Applied) | -40 | 85 | °C | 17 | |||
| VCC Supply Voltage | VCC | -0.5 | 6 | V | 17 | ||
| DC Input Voltage, USBDP and USBDM | -0.5 | 3.8 | V | 17 | |||
| DC Input Voltage, High Impedance Bidirectionals | -0.5 | V | 17 | ||||
| DC Input Voltage, All Other Inputs | -0.5 | V | 17 | ||||
| DC Output Current, Outputs | 24 | mA | 17 | ||||
| Floor Life (Out of Bag) | 168 | Hours | At Factory Ambient (30°C / 60% Relative Humidity) | 17 | |||
| VCC Operating Supply Voltage | VCC1 | 4 | 5.25 | V | Using Internal Oscillator | 18 | |
| VCC Operating Supply Voltage | VCC1 | 3.3 | 5.25 | V | Using External Crystal | 18 | |
| VCCIO Operating Supply Voltage | VCC2 | 1.8 | 5.25 | V | 18 | ||
| Operating Supply Current, USB Suspend | Icc2 | 50 | 70 | 100 | μA | USB Suspend | 18 |
| 3.3V regulator output | 3V3 | 3 | 3.3 | 3.6 | V | 18 | |
| FIFO I/O Output Voltage High (VCCIO=+5.0V, Standard Drive) | Voh | 3.2 | 4.1 | 4.9 | V | VCCIO=+5.0V, standard drive; I source = 2mA | 18 |
| FIFO I/O Output Voltage Low (VCCIO=+5.0V, Standard Drive) | Vol | 0.3 | 0.4 | 0.6 | V | VCCIO=+5.0V, standard drive; I sink = 2mA | 18 |
| FIFO I/O Input Switching Threshold (VCCIO=+5.0V, Standard Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+5.0V, standard drive | 18 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+5.0V, Standard Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+5.0V, standard drive | 18 |
| FIFO I/O Output Voltage High (VCCIO=+3.3V, Standard Drive) | Voh | 2.2 | 2.7 | 3.2 | V | VCCIO=+3.3V, standard drive; I source = 1mA | 18 |
| FIFO I/O Output Voltage Low (VCCIO=+3.3V, Standard Drive) | Vol | 0.3 | 0.4 | 0.5 | V | VCCIO=+3.3V, standard drive; I sink = 2mA | 18 |
| FIFO I/O Input Switching Threshold (VCCIO=+3.3V, Standard Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+3.3V, standard drive | 18 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+3.3V, Standard Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+3.3V, standard drive | 18 |
| FIFO I/O Output Voltage High (VCCIO=+2.8V, Standard Drive) | Voh | 2.1 | 2.6 | 2.8 | V | VCCIO=+2.8V, standard drive; I source = 1mA | 19 |
| FIFO I/O Output Voltage Low (VCCIO=+2.8V, Standard Drive) | Vol | 0.3 | 0.4 | 0.5 | V | VCCIO=+2.8V, standard drive; I sink = 2mA | 19 |
| FIFO I/O Input Switching Threshold (VCCIO=+2.8V, Standard Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+2.8V, standard drive | 19 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+2.8V, Standard Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+2.8V, standard drive | 19 |
| FIFO I/O Output Voltage High (VCCIO=+1.8V, Standard Drive) | Voh | 1.32 | 1.62 | 1.8 | V | VCCIO=+1.8V, standard drive; I source = 0.2mA | 19 |
| FIFO I/O Output Voltage Low (VCCIO=+1.8V, Standard Drive) | Vol | 0.06 | 0.1 | 0.18 | V | VCCIO=+1.8V, standard drive; I sink = 0.5mA | 19 |
| FIFO I/O Input Switching Threshold (VCCIO=+1.8V, Standard Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+1.8V, standard drive | 19 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+1.8V, Standard Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+1.8V, standard drive | 19 |
| FIFO I/O Output Voltage High (VCCIO=+5.0V, High Drive) | Voh | 3.2 | 4.1 | 4.9 | V | VCCIO=+5.0V, high drive; I source = 6mA | 19 |
| FIFO I/O Output Voltage Low (VCCIO=+5.0V, High Drive) | Vol | 0.3 | 0.4 | 0.6 | V | VCCIO=+5.0V, high drive; I sink = 6mA | 19 |
| FIFO I/O Input Switching Threshold (VCCIO=+5.0V, High Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+5.0V, high drive | 19 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+5.0V, High Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+5.0V, high drive | 19 |
| FIFO I/O Output Voltage High (VCCIO=+3.3V, High Drive) | Voh | 2.2 | 2.8 | 3.2 | V | VCCIO=+3.3V, high drive; I source = 3mA | 19 |
| FIFO I/O Output Voltage Low (VCCIO=+3.3V, High Drive) | Vol | 0.3 | 0.4 | 0.6 | V | VCCIO=+3.3V, high drive; I sink = 8mA | 19 |
| FIFO I/O Input Switching Threshold (VCCIO=+3.3V, High Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+3.3V, high drive | 19 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+3.3V, High Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+3.3V, high drive | 19 |
| FIFO I/O Output Voltage High (VCCIO=+2.8V, High Drive) | Voh | 2.1 | 2.6 | 2.8 | V | VCCIO=+2.8V, high drive; I source = 3mA | 20 |
| FIFO I/O Output Voltage Low (VCCIO=+2.8V, High Drive) | Vol | 0.3 | 0.4 | 0.5 | V | VCCIO=+2.8V, high drive; I sink = 8mA | 20 |
| FIFO I/O Input Switching Threshold (VCCIO=+2.8V, High Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+2.8V, high drive | 20 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+2.8V, High Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+2.8V, high drive | 20 |
| FIFO I/O Output Voltage High (VCCIO=+1.8V, High Drive) | Voh | 1.35 | 1.67 | 1.8 | V | VCCIO=+1.8V, high drive; I source = 0.4mA | 20 |
| FIFO I/O Output Voltage Low (VCCIO=+1.8V, High Drive) | Vol | 0.12 | 0.18 | 0.35 | V | VCCIO=+1.8V, high drive; I sink = 3mA | 20 |
| FIFO I/O Input Switching Threshold (VCCIO=+1.8V, High Drive) | Vin | 1 | 1.2 | 1.5 | V | VCCIO=+1.8V, high drive | 20 |
| FIFO I/O Input Switching Hysteresis (VCCIO=+1.8V, High Drive) | VHys | 20 | 25 | 30 | mV | VCCIO=+1.8V, high drive | 20 |
| RESET# and TEST Input Switching Threshold | Vin | 1.3 | 1.6 | 1.9 | V | 20 | |
| RESET# and TEST Input Switching Hysteresis | VHys | 50 | 55 | 60 | mV | 20 | |
| I/O Pins Static Output (Low) | UVol | 0 | 0.3 | V | RI = 1.5kΩ to 3V3OUT (D+); RI = 15kΩ to GND (D-) | 21 | |
| Driver Output Impedance | UDrvZ | 26 | 29 | 44 | Ohms | See Note 1 | 21 |
| Internal Clock Frequency of Operation | 11.98 | 12 | 12.02 | MHz | 21 | ||
| Internal Clock Period | 83.19 | 83.33 | 83.47 | ns | 21 | ||
| Internal Clock Duty Cycle | 45 | 50 | 55 | % | 21 | ||
| OSCI, OSCO Output Voltage High | Voh | 2.1 | 2.8 | 3.2 | V | I source = 3mA; see Note 1 | 21 |
| OSCI, OSCO Output Voltage Low | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 8mA; see Note 1 | 21 |
| OSCI, OSCO Input Switching Threshold | Vin | 1 | 1.2 | 1.5 | V | see Note 1 | 21 |
| Operating Supply Current, Normal Operation | Icc1 | 15 | mA | Normal Operation | 18 |
CAD (KiCad official)
- Symbol:
FT245RL-REEL - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
- 3D model files:
ft245rl-reel-etched.step/ft245rl-reel-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft245rl-reel.step/ft245rl-reel.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FTDI datasheet (37 pp, sha256
a84e5efedfeb9a07, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).