main
Ray
Initial commit: component/drv8847rter
80bd03d
DRV8847RTER
Texas Instruments · Stepper Motor Driver · WQFN-16-EP(3x3)
DRV8847RTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ISEN12 | output | Full-bridge 12 current sensing output. Connect this pin to current-sensing resistor for full-bridge 12, or to GND if current regulation is not needed. |
| 2 | OUT2 | output | Half-bridge output 2 for motor phase control. |
| 3 | OUT4 | output | Half-bridge output 4 for motor phase control. |
| 4 | ISEN34 | output | Full-bridge 34 current sensing output. Connect this pin to current-sensing resistor for full-bridge 34, or to GND if current regulation is not needed. |
| 5 | OUT3 | output | Half-bridge output 3 for motor phase control. |
| 6 | nFAULT | tri_state | Fault indication pin pulled to logic low under fault, overtemp, or UVLO conditions; open-drain output requiring external pull-up resistor. |
| 7 | IN3 | input | Half-bridge input 3 for PWM gate drive control. |
| 8 | IN4 | input | Half-bridge input 4 for PWM gate drive control. |
| 9 | TRQ | input | Torque current scalar input; pull low for 100% torque or high for 50% torque scaling of output current. |
| 10 | VM | power_in | Motor power supply input; bypass to ground using 0.1µF ceramic and 10µF minimum capacitors rated at VM voltage. |
| 11 | GND | power_in | Device ground reference. Ground the GND pin and exposed thermal pad for proper thermal and electrical performance. |
| 12 | MODE | input | Three-state pin for bridge configuration selection: grounded for 4-pin mode, high for 2-pin mode, high for parallel mode, or floating for independent bridge mode. |
| 13 | IN2 | input | Half-bridge input 2 for PWM gate drive control. |
| 14 | IN1 | input | Half-bridge input 1 for PWM gate drive control. |
| 15 | nSLEEP | input | Sleep mode control input; set high to enable device operation, set low to enter low-power sleep mode with 1.7µA quiescent current. |
| 16 | OUT1 | output | Half-bridge output 1 for motor phase control. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16-EP(3x3) |
| Category | Motor Driver ICs |
| Pins | 17 |
CAD (KiCad official)
- Symbol:
DRV8847RTER - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
drv8847rter-etched.step/drv8847rter-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);drv8847rter.step/drv8847rter.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (86 pp, sha256
d437440025a3c724, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# DRV8847RTER
**Texas Instruments** · Stepper Motor Driver · WQFN-16-EP(3x3)
DRV8847RTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ISEN12 | output | Full-bridge 12 current sensing output. Connect this pin to current-sensing resistor for full-bridge 12, or to GND if current regulation is not needed. |
| 2 | OUT2 | output | Half-bridge output 2 for motor phase control. |
| 3 | OUT4 | output | Half-bridge output 4 for motor phase control. |
| 4 | ISEN34 | output | Full-bridge 34 current sensing output. Connect this pin to current-sensing resistor for full-bridge 34, or to GND if current regulation is not needed. |
| 5 | OUT3 | output | Half-bridge output 3 for motor phase control. |
| 6 | nFAULT | tri_state | Fault indication pin pulled to logic low under fault, overtemp, or UVLO conditions; open-drain output requiring external pull-up resistor. |
| 7 | IN3 | input | Half-bridge input 3 for PWM gate drive control. |
| 8 | IN4 | input | Half-bridge input 4 for PWM gate drive control. |
| 9 | TRQ | input | Torque current scalar input; pull low for 100% torque or high for 50% torque scaling of output current. |
| 10 | VM | power_in | Motor power supply input; bypass to ground using 0.1µF ceramic and 10µF minimum capacitors rated at VM voltage. |
| 11 | GND | power_in | Device ground reference. Ground the GND pin and exposed thermal pad for proper thermal and electrical performance. |
| 12 | MODE | input | Three-state pin for bridge configuration selection: grounded for 4-pin mode, high for 2-pin mode, high for parallel mode, or floating for independent bridge mode. |
| 13 | IN2 | input | Half-bridge input 2 for PWM gate drive control. |
| 14 | IN1 | input | Half-bridge input 1 for PWM gate drive control. |
| 15 | nSLEEP | input | Sleep mode control input; set high to enable device operation, set low to enter low-power sleep mode with 1.7µA quiescent current. |
| 16 | OUT1 | output | Half-bridge output 1 for motor phase control. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16-EP(3x3) |
| Category | Motor Driver ICs |
| Pins | 17 |
## CAD (KiCad official)
- Symbol: `DRV8847RTER`
- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`
- 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `drv8847rter-etched.step` / `drv8847rter-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `drv8847rter.step` / `drv8847rter.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/drv8847) (86 pp, sha256 `d437440025a3c724`, retrieved 2026-09-23, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/drv8847rter-datasheet.pdf)