← Commit history

Initial commit: component/drv8847rter

Ray ·80bd03d8b0 ·
2 files changed +252
README.mdadded+54
@@ -0,0 +1,54 @@+# DRV8847RTER++**Texas Instruments** · Stepper Motor Driver · WQFN-16-EP(3x3)++DRV8847RTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | ISEN12 | output | Full-bridge 12 current sensing output. Connect this pin to current-sensing resistor for full-bridge 12, or to GND if current regulation is not needed. |+| 2 | OUT2 | output | Half-bridge output 2 for motor phase control. |+| 3 | OUT4 | output | Half-bridge output 4 for motor phase control. |+| 4 | ISEN34 | output | Full-bridge 34 current sensing output. Connect this pin to current-sensing resistor for full-bridge 34, or to GND if current regulation is not needed. |+| 5 | OUT3 | output | Half-bridge output 3 for motor phase control. |+| 6 | nFAULT | tri_state | Fault indication pin pulled to logic low under fault, overtemp, or UVLO conditions; open-drain output requiring external pull-up resistor. |+| 7 | IN3 | input | Half-bridge input 3 for PWM gate drive control. |+| 8 | IN4 | input | Half-bridge input 4 for PWM gate drive control. |+| 9 | TRQ | input | Torque current scalar input; pull low for 100% torque or high for 50% torque scaling of output current. |+| 10 | VM | power_in | Motor power supply input; bypass to ground using 0.1µF ceramic and 10µF minimum capacitors rated at VM voltage. |+| 11 | GND | power_in | Device ground reference. Ground the GND pin and exposed thermal pad for proper thermal and electrical performance. |+| 12 | MODE | input | Three-state pin for bridge configuration selection: grounded for 4-pin mode, high for 2-pin mode, high for parallel mode, or floating for independent bridge mode. |+| 13 | IN2 | input | Half-bridge input 2 for PWM gate drive control. |+| 14 | IN1 | input | Half-bridge input 1 for PWM gate drive control. |+| 15 | nSLEEP | input | Sleep mode control input; set high to enable device operation, set low to enter low-power sleep mode with 1.7µA quiescent current. |+| 16 | OUT1 | output | Half-bridge output 1 for motor phase control. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WQFN-16-EP(3x3) |+| Category | Motor Driver ICs |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `DRV8847RTER`+- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`+- 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `drv8847rter-etched.step` / `drv8847rter-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `drv8847rter.step` / `drv8847rter.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/drv8847) (86 pp, sha256 `d437440025a3c724`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/drv8847rter-datasheet.pdf)
page.jsonadded+198
@@ -0,0 +1,198 @@+{+  "slug": "drv8847rter",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Stepper Motor Driver, WQFN-16-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "motor driver ics",+    "drv8847rter",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "drv8847rter.kicad_sym",+    "drv8847rter.kicad_mod",+    "drv8847rter.glb",+    "drv8847rter.step",+    "drv8847rter.lbr",+    "docs/hero.png",+    "docs/drv8847rter-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "DRV8847RTER",+    "manufacturer": "Texas Instruments",+    "package": "WQFN-16-EP(3x3)",+    "pin_count": 17,+    "category": "Motor Driver ICs",+    "subcategory": "Stepper Motor Driver",+    "datasheet": "https://www.ti.com/cn/lit/gpn/drv8847",+    "parts": {+      "symbol": "drv8847rter.kicad_sym",+      "footprint": "drv8847rter.kicad_mod",+      "model_3d": "drv8847rter-etched.glb",+      "model_3d_plain": "drv8847rter.glb",+      "model_3d_step": "drv8847rter-etched.step",+      "model_3d_step_plain": "drv8847rter.step",+      "lbr": "drv8847rter.lbr"+    },+    "distributor_links": {+      "lcsc": "C2872056"+    },+    "pins": [+      {+        "number": "1",+        "name": "ISEN12",+        "type": "output",+        "description": "Full-bridge 12 current sensing output. Connect this pin to current-sensing resistor for full-bridge 12, or to GND if current regulation is not needed."+      },+      {+        "number": "2",+        "name": "OUT2",+        "type": "output",+        "description": "Half-bridge output 2 for motor phase control."+      },+      {+        "number": "3",+        "name": "OUT4",+        "type": "output",+        "description": "Half-bridge output 4 for motor phase control."+      },+      {+        "number": "4",+        "name": "ISEN34",+        "type": "output",+        "description": "Full-bridge 34 current sensing output. Connect this pin to current-sensing resistor for full-bridge 34, or to GND if current regulation is not needed."+      },+      {+        "number": "5",+        "name": "OUT3",+        "type": "output",+        "description": "Half-bridge output 3 for motor phase control."+      },+      {+        "number": "6",+        "name": "nFAULT",+        "type": "tri_state",+        "description": "Fault indication pin pulled to logic low under fault, overtemp, or UVLO conditions; open-drain output requiring external pull-up resistor."+      },+      {+        "number": "7",+        "name": "IN3",+        "type": "input",+        "description": "Half-bridge input 3 for PWM gate drive control."+      },+      {+        "number": "8",+        "name": "IN4",+        "type": "input",+        "description": "Half-bridge input 4 for PWM gate drive control."+      },+      {+        "number": "9",+        "name": "TRQ",+        "type": "input",+        "description": "Torque current scalar input; pull low for 100% torque or high for 50% torque scaling of output current."+      },+      {+        "number": "10",+        "name": "VM",+        "type": "power_in",+        "description": "Motor power supply input; bypass to ground using 0.1µF ceramic and 10µF minimum capacitors rated at VM voltage."+      },+      {+        "number": "11",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground reference. Ground the GND pin and exposed thermal pad for proper thermal and electrical performance."+      },+      {+        "number": "12",+        "name": "MODE",+        "type": "input",+        "description": "Three-state pin for bridge configuration selection: grounded for 4-pin mode, high for 2-pin mode, high for parallel mode, or floating for independent bridge mode."+      },+      {+        "number": "13",+        "name": "IN2",+        "type": "input",+        "description": "Half-bridge input 2 for PWM gate drive control."+      },+      {+        "number": "14",+        "name": "IN1",+        "type": "input",+        "description": "Half-bridge input 1 for PWM gate drive control."+      },+      {+        "number": "15",+        "name": "nSLEEP",+        "type": "input",+        "description": "Sleep mode control input; set high to enable device operation, set low to enter low-power sleep mode with 1.7µA quiescent current."+      },+      {+        "number": "16",+        "name": "OUT1",+        "type": "output",+        "description": "Half-bridge output 1 for motor phase control."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Table 5-1 shows '—' for MODE (pin 14) and TRQ (pin 11) in WQFN column, suggesting these pins might n; DRV88471 WQFN variant (Figure 5-5, Table 5-2) shows pins 9 and 12 as NC (no connect) instead of TRQ ; The RTE package suffix denotes WQFN with exposed thermal pad. Ensure thermal pad is properly soldere",+          "exposed pad 17 added from the footprint"+        ],+        "pages_sent": 86,+        "cost_usd": 0.997,+        "at": "2026-09-23T02:26:05"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/drv8847",+        "pages": 86,+        "sha256": "d437440025a3c724",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file