Generated by kicad-footprint-generator · KiCad file format 20260206
ADM691AARWZ-REEL
Analog Devices · Monitors & Reset Circuits · SOIC-16-300mil
ADM691AARWZ-REEL from Analog Devices, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBATT | power_in | Backup battery input for an external battery or capacitor (operating range 0 to 5.5 V); connect to ground if no backup battery is used. |
| 2 | VOUT | power_out | Output to which VCC or VBATT is internally switched, whichever is at the higher potential, supplying up to 250 mA from VCC; connect to VCC if no backup battery is used. |
| 3 | VCC | power_in | +5 V power supply input (4.75 V to 5.5 V for ADM691A/ADM800L, 4.5 V to 5.5 V for ADM693A/ADM800M). |
| 4 | GND | power_in | 0 V ground reference for all signals. |
| 5 | BATT ON | output | Logic output that goes high when VOUT is switched to VBATT and low when switched to VCC; can drive the base (via a resistor) of an external PNP transistor to raise output current above 250 mA. |
| 6 | LOW LINE | output | Logic output that goes low when VCC falls below the reset threshold and returns high as soon as VCC rises above it. |
| 7 | OSC IN | input | Oscillator input: with OSC SEL high or floating, low selects 100 ms and floating selects 1.6 s watchdog timeout; with OSC SEL low it takes an external clock or capacitor to GND setting reset and watchdog timing. |
| 8 | OSC SEL | input | Oscillator select input: floating or high selects the internal oscillator, low enables the external OSC IN; has a 10 µA internal pullup. |
| 9 | PFI | input | Noninverting power fail comparator input with 1.25 V threshold (PFO goes low when PFI is below 1.25 V); connect to GND or VOUT when not used. |
| 10 | PFO | output | Power fail comparator output that goes low when PFI is less than 1.25 V. |
| 11 | WDI | input | Three-level watchdog input: RESET pulses low and WDO goes low if WDI stays high or low longer than the timeout period; watchdog is disabled if WDI is floating or driven to midsupply. |
| 12 | CEOUT | output | Chip enable output that goes low only when CEIN is low and VCC is above the reset threshold; held high when VCC is below the threshold (stays low for 15 µs or until CEIN goes high if CEIN was low at reset assertion). |
| 13 | CEIN | input | Chip enable input to the CE gating circuit; connect to GND or VOUT if not used. |
| 14 | WDO | output | Watchdog logic output that goes low if WDI remains high or low longer than the watchdog timeout period and is set high by the next WDI transition. |
| 15 | ~{RESET} | output | Active-low reset output that goes low if VCC falls below the reset threshold and stays low for 200 ms typ after VCC rises above it. |
| 16 | RESET | output | Active-high reset output, the inverse (complement) of the active-low RESET output, described as open-drain. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOIC-16-300mil |
| Category | Power Management |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC, VBATT Operating Voltage Range | 0 | 5.5 | V | 2 | |||
| Recommended VCC Supply Range (ADM691A, ADM800L) | VCC | 4.75 | 5.5 | V | ADM691A, ADM800L | 2 | |
| Operating Temperature Range (Industrial, A Version) | TA | -40 | 85 | °C | 3 | ||
| Storage Temperature Range | -65 | 150 | °C | 3 | |||
| VCC Voltage | VCC | -0.3 | 6 | V | 3 | ||
| VBATT Voltage | VBATT | -0.3 | 6 | V | 3 | ||
| All Other Inputs Voltage (lower limit) | -0.3 | V | upper limit printed as VOUT + 0.5 V | 3 | |||
| VCC (Peak) Input Current | 1000 | mA | 3 | ||||
| VCC (Continuous) Input Current | 250 | mA | 3 | ||||
| VBATT (Peak) Input Current | 250 | mA | 3 | ||||
| VBATT (Continuous) Input Current | 25 | mA | 3 | ||||
| GND, BATT ON Input Current | 100 | mA | 3 | ||||
| Digital Output Current | 25 | mA | 3 | ||||
| Power Dissipation, R-16 Wide SOIC | 762 | mW | 3 | ||||
| Thermal Impedance θJA, R-16 Wide SOIC | θJA | 110 | °C/W | 3 | |||
| VCC to VOUT Output Resistance | 0.8 | 1.2 | Ω | VCC = 4.5 V | 2 | ||
| Supply Current (Excludes IOUT) | 70 | 100 | µA | VCC > (VBATT, 1 V) | 2 | ||
| Supply Current in Battery Backup (Excludes IOUT) | 0.04 | 1 | µA | VCC < (VBATT, 1.2 V), VBATT = 2.8 V | 2 | ||
| Battery Standby Current (+ = Discharge,, = Charge) | -0.1 | 0.02 | µA | (VBATT +0.2 V) < VCC, TA = +25°C | 2 | ||
| Battery Standby Current (+ = Discharge,, = Charge) | -1 | 0.02 | µA | (VBATT +0.2 V) < VCC | 2 | ||
| BATT ON Output Voltage Low | 0.1 | 0.4 | V | ISINK = 3.2 mA | 2 | ||
| BATT ON Output Voltage Low | 0.7 | 1.5 | V | ISINK = 25 mA | 2 | ||
| BATT ON Output Short Circuit Current | 1 | 15 | 100 | µA | Source Current | 2 | |
| Reset Voltage Threshold | 4.5 | 4.65 | 4.75 | V | ADM691A, ADM800L | 2 | |
| RESET Output Voltage | 0.004 | 0.3 | V | ISINK = 50 µA, VCC = 1 V, VBATT = 0 V | 2 | ||
| RESET Output Voltage | 0.1 | 0.4 | V | ISINK = 3.2 mA, VCC = 4.25 V | 2 | ||
| RESET Output Voltage (high) | 3.5 | V | ISOURCE = 1.6 mA, VCC = 5 V | 2 | |||
| RESET Output Short Circuit Current | 7 | 20 | mA | 2 | |||
| RESET Output Voltage Low | 0.1 | 0.4 | V | ISINK = 3.2 mA | 2 | ||
| Reset Timeout Period, Internal Oscillator | 140 | 200 | 280 | ms | Power Up | 2 | |
| Watchdog Timeout Period, Internal Oscillator (Long Period) | 1 | 1.6 | 2.25 | s | Long Period | 2 | |
| Watchdog Timeout Period, Internal Oscillator (Short Period) | 70 | 100 | 140 | ms | Short Period | 2 | |
| Minimum WDI Input Pulse Width | 100 | ns | VIL = 0.4, VIH = 0.75 × VCC | 2 | |||
| LOW LINE Output Voltage | 0.4 | V | ISINK = 3.2 mA, VCC = 4.25 V | 2 | |||
| LOW LINE Output Voltage (high) | 3.5 | V | ISOURCE = 1 µA, VCC = 5 V | 2 | |||
| LOW LINE Short Circuit Source Current | 1 | 15 | 100 | µA | 2 | ||
| WDO Output Voltage | 0.4 | V | ISINK = 3.2 mA, VCC = 4.25 V | 2 | |||
| WDO Output Voltage (high) | 3.5 | V | ISOURCE = 500 µA, VCC = 5 V | 2 | |||
| WDO Short Circuit Source Current | 3 | 10 | mA | 2 | |||
| WDI Input Threshold, Logic Low | 0.8 | V | 2 | ||||
| WDI Input Current | -50 | -10 | µA | WDI = 0 V | 2 | ||
| WDI Input Current | 20 | 50 | µA | WDI = VOUT | 2 | ||
| PFI Input Threshold (ADM69xA) | 1.2 | 1.25 | 1.3 | V | VCC = 5 V | 2 | |
| PFI Input Current | -25 | 25 | nA | 2 | |||
| PFO Output Voltage (low) | 0.4 | V | ISINK = 3.2 mA | 2 | |||
| PFO Output Voltage (high) | 3.5 | V | ISOURCE = 1 µA | 2 | |||
| PFO Short Circuit Source Current | 1 | 15 | 100 | µA | 2 | ||
| CEIN Leakage Current | -1 | 0.005 | 1 | µA | Disable Mode | 3 | |
| CEIN to CEOUT Resistance | 40 | 150 | Ω | Enable Mode | 3 | ||
| CEOUT Short-Circuit Current | 0.1 | 0.75 | 2 | mA | Disable Mode, CEOUT = 0 V | 3 | |
| CEOUT Output Voltage (high) | 3.5 | V | VCC = 5 V, IOUT = -100 µA | 3 | |||
| CEOUT Output Voltage (high) | 2.7 | V | VCC = 0 V, VBATT = 2.8 V, IOUT = 1 µA | 3 | |||
| OSC IN Input Current | -5 | 0.1 | 5 | µA | OSC SEL = 0 V | 3 | |
| OSC IN Input Pullup Current | 10 | 100 | µA | OSC SEL = VOUT or Floating | 3 | ||
| OSC SEL Input Pullup Current | 10 | 100 | µA | OSC SEL = 0 V | 3 | ||
| OSC IN Frequency Range | 500 | kHz | OSC SEL = 0 V | 3 | |||
| Battery Switchover Hysteresis | 60 | mV | 2 | ||||
| VCC to RESET Delay | 80 | µs | Power Down | 2 |
CAD (KiCad official)
- Symbol:
ADM691AARWZ-REEL - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
adm691aarwz-etched.step/adm691aarwz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adm691aarwz.step/adm691aarwz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (12 pp, sha256
21aaacfd42c57a27, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).