main
History Download
Ray Publish 0.1.0 7a97126

ADM691AARWZ-REEL

Analog Devices · Monitors & Reset Circuits · SOIC-16-300mil

ADM691AARWZ-REEL from Analog Devices, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBATT power_in Backup battery input for an external battery or capacitor (operating range 0 to 5.5 V); connect to ground if no backup battery is used.
2 VOUT power_out Output to which VCC or VBATT is internally switched, whichever is at the higher potential, supplying up to 250 mA from VCC; connect to VCC if no backup battery is used.
3 VCC power_in +5 V power supply input (4.75 V to 5.5 V for ADM691A/ADM800L, 4.5 V to 5.5 V for ADM693A/ADM800M).
4 GND power_in 0 V ground reference for all signals.
5 BATT ON output Logic output that goes high when VOUT is switched to VBATT and low when switched to VCC; can drive the base (via a resistor) of an external PNP transistor to raise output current above 250 mA.
6 LOW LINE output Logic output that goes low when VCC falls below the reset threshold and returns high as soon as VCC rises above it.
7 OSC IN input Oscillator input: with OSC SEL high or floating, low selects 100 ms and floating selects 1.6 s watchdog timeout; with OSC SEL low it takes an external clock or capacitor to GND setting reset and watchdog timing.
8 OSC SEL input Oscillator select input: floating or high selects the internal oscillator, low enables the external OSC IN; has a 10 µA internal pullup.
9 PFI input Noninverting power fail comparator input with 1.25 V threshold (PFO goes low when PFI is below 1.25 V); connect to GND or VOUT when not used.
10 PFO output Power fail comparator output that goes low when PFI is less than 1.25 V.
11 WDI input Three-level watchdog input: RESET pulses low and WDO goes low if WDI stays high or low longer than the timeout period; watchdog is disabled if WDI is floating or driven to midsupply.
12 CEOUT output Chip enable output that goes low only when CEIN is low and VCC is above the reset threshold; held high when VCC is below the threshold (stays low for 15 µs or until CEIN goes high if CEIN was low at reset assertion).
13 CEIN input Chip enable input to the CE gating circuit; connect to GND or VOUT if not used.
14 WDO output Watchdog logic output that goes low if WDI remains high or low longer than the watchdog timeout period and is set high by the next WDI transition.
15 ~{RESET} output Active-low reset output that goes low if VCC falls below the reset threshold and stays low for 200 ms typ after VCC rises above it.
16 RESET output Active-high reset output, the inverse (complement) of the active-low RESET output, described as open-drain.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package SOIC-16-300mil
Category Power Management
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC, VBATT Operating Voltage Range 0 5.5 V 2
Recommended VCC Supply Range (ADM691A, ADM800L) VCC 4.75 5.5 V ADM691A, ADM800L 2
Operating Temperature Range (Industrial, A Version) TA -40 85 °C 3
Storage Temperature Range -65 150 °C 3
VCC Voltage VCC -0.3 6 V 3
VBATT Voltage VBATT -0.3 6 V 3
All Other Inputs Voltage (lower limit) -0.3 V upper limit printed as VOUT + 0.5 V 3
VCC (Peak) Input Current 1000 mA 3
VCC (Continuous) Input Current 250 mA 3
VBATT (Peak) Input Current 250 mA 3
VBATT (Continuous) Input Current 25 mA 3
GND, BATT ON Input Current 100 mA 3
Digital Output Current 25 mA 3
Power Dissipation, R-16 Wide SOIC 762 mW 3
Thermal Impedance θJA, R-16 Wide SOIC θJA 110 °C/W 3
VCC to VOUT Output Resistance 0.8 1.2 Ω VCC = 4.5 V 2
Supply Current (Excludes IOUT) 70 100 µA VCC > (VBATT, 1 V) 2
Supply Current in Battery Backup (Excludes IOUT) 0.04 1 µA VCC < (VBATT, 1.2 V), VBATT = 2.8 V 2
Battery Standby Current (+ = Discharge,, = Charge) -0.1 0.02 µA (VBATT +0.2 V) < VCC, TA = +25°C 2
Battery Standby Current (+ = Discharge,, = Charge) -1 0.02 µA (VBATT +0.2 V) < VCC 2
BATT ON Output Voltage Low 0.1 0.4 V ISINK = 3.2 mA 2
BATT ON Output Voltage Low 0.7 1.5 V ISINK = 25 mA 2
BATT ON Output Short Circuit Current 1 15 100 µA Source Current 2
Reset Voltage Threshold 4.5 4.65 4.75 V ADM691A, ADM800L 2
RESET Output Voltage 0.004 0.3 V ISINK = 50 µA, VCC = 1 V, VBATT = 0 V 2
RESET Output Voltage 0.1 0.4 V ISINK = 3.2 mA, VCC = 4.25 V 2
RESET Output Voltage (high) 3.5 V ISOURCE = 1.6 mA, VCC = 5 V 2
RESET Output Short Circuit Current 7 20 mA 2
RESET Output Voltage Low 0.1 0.4 V ISINK = 3.2 mA 2
Reset Timeout Period, Internal Oscillator 140 200 280 ms Power Up 2
Watchdog Timeout Period, Internal Oscillator (Long Period) 1 1.6 2.25 s Long Period 2
Watchdog Timeout Period, Internal Oscillator (Short Period) 70 100 140 ms Short Period 2
Minimum WDI Input Pulse Width 100 ns VIL = 0.4, VIH = 0.75 × VCC 2
LOW LINE Output Voltage 0.4 V ISINK = 3.2 mA, VCC = 4.25 V 2
LOW LINE Output Voltage (high) 3.5 V ISOURCE = 1 µA, VCC = 5 V 2
LOW LINE Short Circuit Source Current 1 15 100 µA 2
WDO Output Voltage 0.4 V ISINK = 3.2 mA, VCC = 4.25 V 2
WDO Output Voltage (high) 3.5 V ISOURCE = 500 µA, VCC = 5 V 2
WDO Short Circuit Source Current 3 10 mA 2
WDI Input Threshold, Logic Low 0.8 V 2
WDI Input Current -50 -10 µA WDI = 0 V 2
WDI Input Current 20 50 µA WDI = VOUT 2
PFI Input Threshold (ADM69xA) 1.2 1.25 1.3 V VCC = 5 V 2
PFI Input Current -25 25 nA 2
PFO Output Voltage (low) 0.4 V ISINK = 3.2 mA 2
PFO Output Voltage (high) 3.5 V ISOURCE = 1 µA 2
PFO Short Circuit Source Current 1 15 100 µA 2
CEIN Leakage Current -1 0.005 1 µA Disable Mode 3
CEIN to CEOUT Resistance 40 150 Ω Enable Mode 3
CEOUT Short-Circuit Current 0.1 0.75 2 mA Disable Mode, CEOUT = 0 V 3
CEOUT Output Voltage (high) 3.5 V VCC = 5 V, IOUT = -100 µA 3
CEOUT Output Voltage (high) 2.7 V VCC = 0 V, VBATT = 2.8 V, IOUT = 1 µA 3
OSC IN Input Current -5 0.1 5 µA OSC SEL = 0 V 3
OSC IN Input Pullup Current 10 100 µA OSC SEL = VOUT or Floating 3
OSC SEL Input Pullup Current 10 100 µA OSC SEL = 0 V 3
OSC IN Frequency Range 500 kHz OSC SEL = 0 V 3
Battery Switchover Hysteresis 60 mV 2
VCC to RESET Delay 80 µs Power Down 2

CAD (KiCad official)

  • Symbol: ADM691AARWZ-REEL
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: adm691aarwz-etched.step / adm691aarwz-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); adm691aarwz.step / adm691aarwz.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (12 pp, sha256 21aaacfd42c57a27, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF