component
A6211GLJTR-T
Public Made by Adomby adom
Allegro MicroSystems LLC LED Drivers, SOIC-8-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.2
9c87d06
A6211GLJTR-T
Allegro MicroSystems LLC · LED Drivers · SOIC-8-EP
A6211GLJTR-T from Allegro MicroSystems LLC, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Supply voltage input, specified from 6 to 48 V with an absolute maximum of -0.3 to 50 V, and it also sets the on-time through the RON resistor to the TON pin. |
| 2 | TON | passive | Regulator on-time setting resistor terminal, where RON is connected between VIN and TON to program the switching frequency (fSW = 1 / [k × (RON + RINT)] with k = 0.0139 and RINT = 5 kΩ internal). |
| 3 | EN | input | Logic input for enable and PWM dimming, with VIH minimum 1.8 V and VIL maximum 0.4 V, a high-voltage tolerant input that needs a 1 kΩ series resistor if it is driven above VIN. |
| 4 | CS | input | Drive output current sense feedback, where the average CS voltage is regulated at VCSREG = 200 mV typical (187.5 to 210 mV) across the LED current sense resistor, with an absolute maximum of -0.3 to 7 V. |
| 5 | VCC | power_out | Internal linear regulator output regulated at 5.1 to 5.7 V for 0 mA < ICC < 5 mA, with an absolute maximum of -0.3 to 7 V to GND, and it is not designed to drive an external load. |
| 6 | GND | power_in | Ground terminal for the device, which is also the reference for the exposed pad connection. |
| 7 | BOOT | passive | DMOS gate driver bootstrap terminal, where the bootstrap capacitor C4 is placed near this pin, with VBOOT rated from -0.3 to VIN + 8 V. |
| 8 | SW | output | Switched output terminal driving the inductor, with switching voltage rated from -1.5 to VIN + 0.3 V and buck switch current limit of 3.0 to 5.0 A. |
| 9 | PAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems LLC |
| Package | SOIC-8-EP |
| Category | LED Drivers |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Supply Voltage | VIN | 6 | 48 | V | TA = 25°C | 4 | |
| Buck Switch Current Limit Threshold | ISWLIM | 3 | 4 | 5 | A | 4 | |
| Buck Switch On-Resistance | RDS(on) | 0.25 | 0.4 | Ω | VBOOT = VIN + 4.3 V, TA = 25°C, ISW = 1 A | 4 | |
| VIN Pin Shutdown Current | IINSD | 1 | 10 | µA | EN shorted to GND | 4 | |
| BOOT Undervoltage Lockout Threshold | VBOOTUV | 1.7 | 2.9 | 4.3 | V | VBOOT to VSW increasing | 4 |
| Switching Minimum Off-Time | tOFFmin | 110 | 150 | ns | VCS = 0 V | 4 | |
| Switching Minimum On-Time | tONmin | 110 | 150 | ns | 4 | ||
| Selected On-Time | tON | 800 | 1000 | 1200 | ns | VIN = 24 V, VOUT = 12 V, RON = 137 kΩ | 4 |
| Load Current Sense Regulation Threshold | VCSREG | 187.5 | 200 | 210 | mV | VCS decreasing, SW turns on | 4 |
| VCC Regulated Output | VCC | 5.1 | 5.4 | 5.7 | V | 0 mA < ICC < 5 mA, VIN > 6 V | 4 |
| VCC Current Limit | ICCLIM | 5 | 20 | mA | VIN = 24 V, VCC = 0 V | 4 | |
| Logic High Voltage | VIH | 1.8 | V | VEN increasing | 4 | ||
| Logic Low Voltage | VIL | 0.4 | V | VEN decreasing | 4 | ||
| Maximum PWM Dimming Off-Time | tPWML | 10 | 17 | ms | Measured while EN = low, during dimming control, and internal references are powered-on | 4 | |
| Supply Voltage | VIN | -0.3 | 50 | V | 2 | ||
| Bootstrap Drive Voltage | VBOOT | -0.3 | V | Printed as VIN +8 V; upper limit is not a fixed number | 2 | ||
| Switching Voltage | VSW | -1.5 | V | Printed as VIN +0.3 V; upper limit is not a fixed number | 2 | ||
| Linear Regulator Terminal | VCC | -0.3 | 7 | V | VCC to GND | 2 | |
| Enable and TON Voltage | VEN, VTON | -0.3 | V | Printed as VIN +0.3 V; upper limit is not a fixed number | 2 | ||
| Current Sense Voltage | VCS | -0.3 | 7 | V | 2 | ||
| Operating Ambient Temperature | TA | -40 | 105 | °C | G temperature range | 2 | |
| Maximum Junction Temperature | TJ(max) | 150 | °C | 2 | |||
| Storage Temperature | Tstg | -55 | 150 | °C | 2 | ||
| Package Thermal Resistance (Junction to Ambient), 4-layer PCB | RθJA | 35 | °C/W | On 4-layer PCB based on JEDEC standard | 2 | ||
| Package Thermal Resistance (Junction to Ambient), 2-layer PCB | RθJA | 62 | °C/W | On 2-layer generic test PCB with 0.8 in.2 of copper area each side | 2 | ||
| Package Thermal Resistance (Junction to Pad) | RθJP | 2 | °C/W | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | It is lead (Pb) free, with 100% matte-tin leadframe plating. A6211-DS, Rev. 5 | 1 |
CAD (KiCad official)
- Symbol:
A6211GLJTR-T - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files:
a6211gljtr-t-etched.step/a6211gljtr-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);a6211gljtr-t.step/a6211gljtr-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Allegro MicroSystems LLC datasheet (18 pp, sha256
48373dd80f837b74, retrieved 2026-11-13, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# A6211GLJTR-T
**Allegro MicroSystems LLC** · LED Drivers · SOIC-8-EP
A6211GLJTR-T from Allegro MicroSystems LLC, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Supply voltage input, specified from 6 to 48 V with an absolute maximum of -0.3 to 50 V, and it also sets the on-time through the RON resistor to the TON pin. |
| 2 | TON | passive | Regulator on-time setting resistor terminal, where RON is connected between VIN and TON to program the switching frequency (fSW = 1 / [k × (RON + RINT)] with k = 0.0139 and RINT = 5 kΩ internal). |
| 3 | EN | input | Logic input for enable and PWM dimming, with VIH minimum 1.8 V and VIL maximum 0.4 V, a high-voltage tolerant input that needs a 1 kΩ series resistor if it is driven above VIN. |
| 4 | CS | input | Drive output current sense feedback, where the average CS voltage is regulated at VCSREG = 200 mV typical (187.5 to 210 mV) across the LED current sense resistor, with an absolute maximum of -0.3 to 7 V. |
| 5 | VCC | power_out | Internal linear regulator output regulated at 5.1 to 5.7 V for 0 mA < ICC < 5 mA, with an absolute maximum of -0.3 to 7 V to GND, and it is not designed to drive an external load. |
| 6 | GND | power_in | Ground terminal for the device, which is also the reference for the exposed pad connection. |
| 7 | BOOT | passive | DMOS gate driver bootstrap terminal, where the bootstrap capacitor C4 is placed near this pin, with VBOOT rated from -0.3 to VIN + 8 V. |
| 8 | SW | output | Switched output terminal driving the inductor, with switching voltage rated from -1.5 to VIN + 0.3 V and buck switch current limit of 3.0 to 5.0 A. |
| 9 | PAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems LLC |
| Package | SOIC-8-EP |
| Category | LED Drivers |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Supply Voltage | VIN | 6 | | 48 | V | TA = 25°C | 4 |
| Buck Switch Current Limit Threshold | ISWLIM | 3 | 4 | 5 | A | | 4 |
| Buck Switch On-Resistance | RDS(on) | | 0.25 | 0.4 | Ω | VBOOT = VIN + 4.3 V, TA = 25°C, ISW = 1 A | 4 |
| VIN Pin Shutdown Current | IINSD | | 1 | 10 | µA | EN shorted to GND | 4 |
| BOOT Undervoltage Lockout Threshold | VBOOTUV | 1.7 | 2.9 | 4.3 | V | VBOOT to VSW increasing | 4 |
| Switching Minimum Off-Time | tOFFmin | | 110 | 150 | ns | VCS = 0 V | 4 |
| Switching Minimum On-Time | tONmin | | 110 | 150 | ns | | 4 |
| Selected On-Time | tON | 800 | 1000 | 1200 | ns | VIN = 24 V, VOUT = 12 V, RON = 137 kΩ | 4 |
| Load Current Sense Regulation Threshold | VCSREG | 187.5 | 200 | 210 | mV | VCS decreasing, SW turns on | 4 |
| VCC Regulated Output | VCC | 5.1 | 5.4 | 5.7 | V | 0 mA < ICC < 5 mA, VIN > 6 V | 4 |
| VCC Current Limit | ICCLIM | 5 | 20 | | mA | VIN = 24 V, VCC = 0 V | 4 |
| Logic High Voltage | VIH | 1.8 | | | V | VEN increasing | 4 |
| Logic Low Voltage | VIL | | | 0.4 | V | VEN decreasing | 4 |
| Maximum PWM Dimming Off-Time | tPWML | 10 | 17 | | ms | Measured while EN = low, during dimming control, and internal references are powered-on | 4 |
| Supply Voltage | VIN | -0.3 | | 50 | V | | 2 |
| Bootstrap Drive Voltage | VBOOT | -0.3 | | | V | Printed as VIN +8 V; upper limit is not a fixed number | 2 |
| Switching Voltage | VSW | -1.5 | | | V | Printed as VIN +0.3 V; upper limit is not a fixed number | 2 |
| Linear Regulator Terminal | VCC | -0.3 | | 7 | V | VCC to GND | 2 |
| Enable and TON Voltage | VEN, VTON | -0.3 | | | V | Printed as VIN +0.3 V; upper limit is not a fixed number | 2 |
| Current Sense Voltage | VCS | -0.3 | | 7 | V | | 2 |
| Operating Ambient Temperature | TA | -40 | | 105 | °C | G temperature range | 2 |
| Maximum Junction Temperature | TJ(max) | | | 150 | °C | | 2 |
| Storage Temperature | Tstg | -55 | | 150 | °C | | 2 |
| Package Thermal Resistance (Junction to Ambient), 4-layer PCB | RθJA | | 35 | | °C/W | On 4-layer PCB based on JEDEC standard | 2 |
| Package Thermal Resistance (Junction to Ambient), 2-layer PCB | RθJA | | 62 | | °C/W | On 2-layer generic test PCB with 0.8 in.2 of copper area each side | 2 |
| Package Thermal Resistance (Junction to Pad) | RθJP | | 2 | | °C/W | | 2 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | It is lead (Pb) free, with 100% matte-tin leadframe plating. A6211-DS, Rev. 5 | 1 |
## CAD (KiCad official)
- Symbol: `A6211GLJTR-T`
- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm`
- 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files: `a6211gljtr-t-etched.step` / `a6211gljtr-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `a6211gljtr-t.step` / `a6211gljtr-t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Allegro MicroSystems LLC datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586199868038004736) (18 pp, sha256 `48373dd80f837b74`, retrieved 2026-11-13, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/a6211gljtr-t-datasheet.pdf)